Cisco Security :: C2911 - Enable SSL VPN License

Jul 3, 2012

i had installed the SSL_VPN to the router C2911, running on IOS 15.0 But i couldn't see the SSL_VPN enable while i do show license feature? i did reload the router several time and accept the end user agreement.
 
attach the
01. show license feature
02. show license detail

View 1 Replies


ADVERTISEMENT

Cisco WAN :: C2911 Failed License Install

Feb 17, 2012

I have few licenses to be installed in my c2911/k9 router but there were errors while installing the license. [code]

View 5 Replies View Related

Cisco Firewall :: Difference Of VPN Plus License And Security Plus License ASA 5520

Oct 16, 2012

What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.

View 1 Replies View Related

Cisco WAN :: Specific License In Order To Enable NBAR2 In ISRG2 892 With IOS

Aug 22, 2012

I was wondering to understand if there is an specific license in order to enable NBAR2 in my ISRG2 892 with IOS 15.2(3)T. If not, what is the basic license I need to have for NBAR2 ?

View 5 Replies View Related

Cisco Switching/Routing :: Catalyst 3850 - Additional License To Enable Controller Functionality?

Feb 10, 2013

Based on what i am reading on the Catalyst 3850 datasheet, the controller functionality comes by default if i have a IP Base of IP Services license on the switch. Is this correct or do i need additional license to enable the controller functionality?What capabilities does below license provide ?
 
LIC-CT3850-UPG (Primary upgrade license SKU for Cisco 3850 wireless controller)

View 1 Replies View Related

Cisco Security :: 880 NPE / How To Change License

Mar 26, 2012

i have cisco 880 with NPE licence, but i need encryption on this device. I change IOS to c880data-universalk9-mz.151-3.T1.bin, but i still have NPE License and only Evalution without NPE. How  can i have permanent license?
 
show license all
 
License Store: Primary License Storage
 StoreIndex: 0   Feature: advsecurity_npe                   Version: 1.0
License Type: Permanent
License State: Active, Not in Use

[code]....

View 3 Replies View Related

Cisco VPN :: ASA 5510 - Security Plus License

Aug 21, 2012

We’ve ordered ASA 5510 with security plus license as below description: 

ASA5510-K8
ASA 5510 Appliance with SW,   5FE, DES
L-ASA5510-SEC-PL=
ASA 5510 Security Plus License   w/ HA, GE, more VLANs + conns
 
The license details on the appliance shows as the below,
Fail over                        : Enabled 
Encryption-DES                  : Enabled 
Encryption-3DES-AES             : Disabled
Security Contexts                : Default 
GTP/GPRS                        : Disabled
Any Connect Premium Peers      : Default 
Other VPN Peers                 : Default 
Advanced Endpoint Assessment    : Disabled
Any Connect for Mobile            : Disabled
Any Connect for Cisco VPN Phone  : Disabled
Shared License                  : Disabled
UC Phone Proxy Sessions          : Default 
Total UC Proxy Sessions          : Default 
Any Connect Essentials            : Disabled
Bot net Traffic Filter            : Disabled
Inter company Media Engine        : Disabled 
  
I’ve noticed that the 3DES is disabled, do I need to order another license to use 3DES or not ?Also, I need 2 ~ 5 branches to connect simultaneously and have VPN access on their laptops to the main branch via vpn software, which VPN software I should use and is our license enough or I should order another license.

View 3 Replies View Related

Cisco Firewall :: Do Need Security Plus License To Do HA With Two 5520

Mar 7, 2011

Do I need the security plus license to do HA with two 5520's?I was told by our purchasing department that the 5520 was supposed to be able to do HA out of the box, but when I look I see only the VPN + license.  Does that mean I can download the security plus license?  Or do I even need it on the 5520.

View 2 Replies View Related

Cisco Firewall :: Security Plus License For ASA5505

Jul 2, 2012

I have Cisco ASA5505 8.2(5) connected with Cisco 5520 8.2(1) via IPSEC tunnel, I was able to SSH from the inside 5520 to inside IP of the asa5505. but I after I upgrade the license to security plus at 5505 I lost the SSH and ASDM to inside IP of 5505 from the inside network of the 5520. however I still can use SSH and ASDM on outside IP of 5505.
 
I did a lot of testing to make it work but I couldn't I added SSH 0.0.0.0/0 inside and outside also I added acl on both interfaces. when I did a trace on the outside interface from the private network of 5520 to 5505 inside IP I got IPSEC spoofed by the way that trace only works with security plus because I try to test on all my other firewalls 8.2(5) it shows nothing and all my firewalls can accessed from the private network 5520 except the one with the security plus!

View 11 Replies View Related

Cisco WAN :: 1921 - IOS Upgrade With Security License?

Nov 4, 2011

I have a Cisco 1921 ISR Router with Security License running software version 15.0. I want to upgrade the router to 15.1. But I don't want to lose the security license that came with the router. When I look at the IOS downloads page on Cisco, all I see is universal images for all versions of 15.1.
 
My question is - where is the security license stored? In the IOS or programmed in somewhere else of the router? If I upgrade my router to one of the newer 15.1 universal images, will I lose my security license?

View 2 Replies View Related

Cisco VPN :: 2911 - VPN License / Security Pack

Sep 25, 2012

We are designing a solution for our customer, they plan to connect 5 site to their main office, on the main office, they use CISCO2911, branch use CISCO1921, so my question is:
 
1, If I want to use IPSec VPN connect branch and main office, apart from the router, I only need to buy the Security pack, like SL-19-SEC-K9/SL-29-SEC-K9, no need to buy SL-19-DATA-K9/SL-29-DATA-K9, am I right? 

2, If I want to use SSL VPN connect branch and main office, apart from the router and SL-19-SEC-K9/SL-29-SEC-K9, I only need to buy L-FL-SSLVPN10-K9 for CISCO2911 in main office, no need to buy L-FL-SSLVPN10-K9 for branch as each CISCO1921 has two default SSL license?

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Security Plus License Upgrade?

Apr 19, 2012

We want to upgrade one of our Cisco 5505 with Security Plus license. what is the difference between L-ASA5505-SEC-PL and ASA5505-SEC-PL upgrade licenses?

View 1 Replies View Related

Cisco Firewall :: Security Context License On 5550

Dec 9, 2012

 I need your support for upgrading the Security context license on 5550, at present we have 5 Security context license installed in ASA but we want it to increased till 10 conctexts. I want to understand if we need to get addtional 5 Security context license or 10.     

View 5 Replies View Related

Cisco WAN :: Upgrade License 1941-K9 From IPBase To Security

Oct 25, 2011

I would like to Upgrade license Cisco 1941-K9 from ipbase to security

View 5 Replies View Related

Cisco Firewall :: ASA 5510 - Difference Between CSC-10-PLUS And Security Plus License

Mar 3, 2011

I have ASA 5510. Is there any difference between CSC-10-PLUS license and Security Plus License...

View 3 Replies View Related

Cisco Switching/Routing :: Router 1941 Security License?

Mar 12, 2013

I have a cisco router 1941 and i have uploaded before evaluation license , now i have already bought cisco security license .I have already installed on cisco router , but the problem the router is still using  the evaluation license not the new license .
 
RSP#sh flash:
-#- --length-- -----date/time------ path
1     55088360 Oct 10 2012 06:04:10 +00:00 c1900-universalk9-mz.SPA.151-4.M4.bin
2         2903 Feb 4 2013 12:23:32 +00:00 cpconfig-19xx.cfg

[Code].....

View 19 Replies View Related

Cisco Security :: ASA 5545 - 8.6 - Active / Standby - License Upgrade

Feb 4, 2013

We are planning to upgrade the ASA license in an A/S pair by adding the ASA5500-SC-20= license. The ASA is 5545 and runs 8.6. According to documentation, after 8.3 version, the ASAs can share a license features and do not require the same license on both boxes. I run a test in GNS3 with 8.4(2) images and I saw that by adding the 'activation-key' command only on the primary unit did the job as the 'show activation-key' output shows. In order to be 100% sure would like to verify the following:

Putting the activation-key only on the primary unit is enough and there is no need to do anything elseIn case the primary unit is standby, again we have to put the actication-key command on the primary unit (I am asking this because the 'activation-key' command is not listed under the commands that are not replicated to the other unitk, but doesn't make sense to be replicated since the activation-key is 'tied' with the S/N of the device).

View 4 Replies View Related

Cisco Security :: Remove License Previously Installed On ASA 5510?

Nov 15, 2010

I'm currently reconfiguring an ASA5510 installation to a HA setup with a second 5510. The old 5510 has an "AnyConnect for Mobile" license which isn't being used. So we upgrade that one to a SecPlus License to enable failover posibilities and we bought a new 5510 also with a SecPlus license. When I'm trying to enable failover I get the message that my mate hasn't got the "AnyConnect for Mobile" license. I know for failover both devices must be exactly the same (at first i thougth that the AnyConnect license would be lost when upgrading to SecPlus). So now I'm wondering and searching for solutions to remove the AnyConnect license (because we don't use it).

View 7 Replies View Related

Cisco Firewall :: Security Context License Requirement - ASA5520

Jan 14, 2013

A simple question - I have ASA 5520s and was wondering what license is required to create multiple (more than default 2) security contexts.

The ASA already have ASA 5520 VPN Plus license.
 
Software Version 8.4(1)

View 2 Replies View Related

Cisco Firewall :: Adding Second Subnet On ASA 5505 With Security Plus License

Jan 31, 2012

We recently upgraded a ASA 5505 with the security plus license to allow us to add a second subnet, but are having a few problems configuring the second subnet.  The original subnet we have configured 10.1.1.0 is able to access the internet without any problems.  However the new subnet 10.1.5.0 is unable to access the internet and when we ran a trace packet the nat config nat (inside) 1 0.0.0.0 0.0.0.0 is showing as the rule that drops the packet.
 
Additionally we have not been able to get the 2 subnets to talk to each other even though same-security-traffic permit inter-interface is configured.  How to configure the subnet 10.1.5.0 to access the internet or to get the subnets to communicate.  Below is a streamlined version of our current config.

!interface Vlan1nameif insidesecurity-level 100ip address 10.1.1.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 66.66.66.66 255.255.255.240 ospf cost 10!interface Vlan13nameif corporatesecurity-level 100ip

[Code].....

View 15 Replies View Related

Cisco Firewall :: ASA 5505 Security License And Vlans Supported?

May 18, 2013

I am buying ASA 5505 with security  license. It says it can support 20 vlans does it support 20 vlans by allowing to create subinterfaces? As it has 8 physical ports only?

View 3 Replies View Related

Cisco Firewall :: ASA 5510 With Security Plus License Lost Contexts

Jan 28, 2013

I have a ASA 5510 with Security Plus License and when I looked at the devices a few days ago I had 2 contexts, however after configuring the Mgm port as a regular port the contexts show 0, why?  I can not find any post on the internet where this issue has happen:  here is the output from show ver:

Cisco Adaptive Security Appliance Software Version 7.0(8)
Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"

[Code]......

View 3 Replies View Related

Cisco Switching/Routing :: License Upgrade In 2900 For Security K9 Feature?

Dec 18, 2012

i have 2921 router with base license . i want to upgrade to it to security k9 feature or want to enable it. i have license file with product activation key. how should i do it. if any body have screen shot file

View 1 Replies View Related

Cisco Firewall :: ASA5510 Security Context License Transfer To Another Device

Apr 30, 2012

Is it possivble to have 10 security licenses, license to a Cisco 5510 and have them transfeered to a Cisco5520?    

View 1 Replies View Related

Enable Security On DLink Dir 615?

Aug 8, 2011

my dir615 is unsecured how do i make it secure

View 1 Replies View Related

How To Enable Wireless Security

May 18, 2011

I have new modell bendlex small modem. i want to enable security i configure wap personal but i canot access my modem i am using windows 7. what about TIK and AES anything related to configure security..

View 1 Replies View Related

Enable Security On Dir 615 D-link?

Sep 4, 2011

I have D-Link wireless N Home Router.How do i enable security on DIR-615

View 1 Replies View Related

Cisco :: Re-enable A Port After A Security Violation?

Sep 23, 2011

I'm using packet tracer, I enabled port security on fa0/18 and set it to shut down when a violation occurred, I set it to only allow 1 mac address, so I tested it by plugging in another PC and the port shut down so the security was working, however when I plug the old pc back into the port it still stays shut down, how do I activate it again.

FastEthernet0/18 is down, line protocol is down (err-disabled)

View 3 Replies View Related

Cisco :: Enable Port Security In Switches?

Jul 2, 2012

I have applied port security in one cisco switch and i have enabled port security in one port.I have applied port security as sticky and applied "restrict" on violation of the portsecurity.Now i have connected a PC to that switch port. Later i have connected another PC. The packets got dropped. But when i connected the original PC again, the packets flow started again.So, i have a doubt. Will the packet flow get establish, when the original PC is connected again to a port which is applied with port security violation "Restrict"?

View 2 Replies View Related

Cisco Security :: How To Enable Netflow On ASA 5540

Sep 3, 2008

How to enable Netflow on the ASA5540

View 10 Replies View Related

Cisco WAN :: C2911 - USBFlash Not Working?

May 3, 2013

I tried to copy my conf file to a USBflash drive but I cannot initialize the USBflash drive.It asks me to format the USBflash, but when I say "yes" it gives an error.
 
Feb 21 11:18:40.799: %USBFLASH-5-CHANGE: usbflash1 has been inserted!
Feb 21 11:19:00.803: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values in partition table or boot sector.  Device needs formatting before use!
yourname#fort
yourname#for
yourname#format usb

[code]...

When I connect it to a 2811 its working perfectly
 
OOHQ_GWVO_01#sh usbflash0:No files on device
2116747264 bytes available (0 bytes used)
OOHQ_GWVO_01#dir usbflOOHQ_GWVO_01#dir usbflash0:Directory of usbflash0:/
No files in directory
2116747264 bytes total (2116747264 bytes free)OOHQ_GWVO_01#

View 1 Replies View Related

Cisco WAN :: USBFlash Not Working C2911

Feb 20, 2012

I tried to copy my conf file to a USBflash drive but I cannot initialize the USBflash drive.
 
It asks me to format the USBflash, but when I say "yes" it gives an error.
 
Feb 21 11:18:40.799: %USBFLASH-5-CHANGE: usbflash1 has been inserted!
Feb 21 11:19:00.803: %USBFLASH-4-FORMAT: usbflash1 contains unexpected values in partition table or boot sector.  Device needs formatting before use!

[Code].....

View 3 Replies View Related

Cisco Firewall :: Update License Content Security And Control Info ASA 5510

Mar 20, 2013

I have to upgrade to an ASA 5510 CSC, and the new license is generated, the file you sent me licensing, only seen this:Activation Code not required for this renewal. Please go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date (BASE: 09/04/2014, PLUS: 09/04/2014).This means that what I have not make any upgrades or license charge in the ASA? Does the automatic update is made?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved