I'm using packet tracer, I enabled port security on fa0/18 and set it to shut down when a violation occurred, I set it to only allow 1 mac address, so I tested it by plugging in another PC and the port shut down so the security was working, however when I plug the old pc back into the port it still stays shut down, how do I activate it again.
FastEthernet0/18 is down, line protocol is down (err-disabled)
My group has recently started configuring traps on our switches to alert us of issues as they arise vs. waiting for the Helpdesk to receive user complaints and then responding.We have successfully configured the 2950 and 2960 switches to alert us when a port-security violation happens. However, the 3750 switches refuse to fire the port-security violation traps. The 3750's will fire an errdisable trap when the port goes down though.
Here is one of the port configurations:
interface FastEthernet1/0/45
switchport access vlan 5
switchport mode access
switchport port-security
switchport port-security mac-address sticky
[code].....
And here is the output of the port-security debug:
2522070: Oct 21 16:37:04: %LINK-3-UPDOWN: Interface FastEthernet1/0/45, changed state to down
2522089: Oct 21 16:37:05: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa1/0/45, putting Fa1/0/45 in err-disable state
2522100: Oct 21 16:37:05: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0012.3f07.95d3 on port FastEthernet1/0/45.
All of the 3750's are running C3750-IPBASEK9-M, Version 12.2(53) SE2. Wireshark also shows the errdisable traps, but no other traps so I've ruled out the traps being missed. All of the switches have been reloaded and power cycled.
I have applied port security in one cisco switch and i have enabled port security in one port.I have applied port security as sticky and applied "restrict" on violation of the portsecurity.Now i have connected a PC to that switch port. Later i have connected another PC. The packets got dropped. But when i connected the original PC again, the packets flow started again.So, i have a doubt. Will the packet flow get establish, when the original PC is connected again to a port which is applied with port security violation "Restrict"?
View 2 Replies View RelatedWLC 4404 is configured as Anchor controller, the MAC violation are captured by Controller. the Violated MAC are deleted manually through GUI, but when tried deleting through CLI using command
>Config exclusionlist delete <mac address>
we get error message as error deleting user <mac address>
I need a WCS report that will actually give me the top n Wireless Access points that have too many clients trying to authenticte to them.We have some serious capacity issue in meeting rooms but we need a ball park figure of how many WAPs might be affected.
I know I can interogate the WCS to drill down and find out that WAPs are exceeding their threshold I just need to have a decent report generated.I have searched the reports from WCS 6.0.202.0 and cannot seem to find anything that suits.
my dir615 is unsecured how do i make it secure
View 1 Replies View RelatedI have new modell bendlex small modem. i want to enable security i configure wap personal but i canot access my modem i am using windows 7. what about TIK and AES anything related to configure security..
View 1 Replies View RelatedI have D-Link wireless N Home Router.How do i enable security on DIR-615
View 1 Replies View Relatedmy firewall log is full of entries listing policy violations rejections. These look like traffic from LAN to WAN that is being rejected, right? [code]Noted that most of the rejections are in the 40,000-60,000 port range.
-new RV042G
-WAN 1 set to 10.x
-LAN 192.168.1.1
Action Interface SourceInterface Source Destination Time
1. Allow All Traffic [1] LAN Any Any Always
2. Deny All Traffic [1] WAN1 Any Any Always
3. Deny All Traffic [1] WAN2 Any Any Always
Have tried re-flashing firmware to current version (was already on it), disabled SPI, disabling Denial of Service, all no change.Also noted another issue with logging; bug? When the router was brand new out of box and again after firmware flash:
* the "All" drop down of System Log was BLANK, not logging any entries although other drop downs such as "System Log and Firewall Log were
* email alerts were not being triggered for log entries
* clear log button appears to resolve the issue after which the ALL shows all entries now
i had installed the SSL_VPN to the router C2911, running on IOS 15.0 But i couldn't see the SSL_VPN enable while i do show license feature? i did reload the router several time and accept the end user agreement.
attach the
01. show license feature
02. show license detail
How to enable Netflow on the ASA5540
View 10 Replies View RelatedInherited a Linksys 2.4ghz 802.11b wireless router and although I have added apassword, it sti ll shows security disabled when using it. And yes, I still have typing issues?
View 3 Replies View Relatedenable security with linksys e1000. it has a password key before but it automatically disabled.
View 1 Replies View RelatedHow to enable security mode on DLINK wireless router DIR-615, after having it installed in "unsercured mode"?
View 1 Replies View RelatedI just purchased a new laptop and because I didn't remember my router password I reset it. although I do have internet connection it is not secured. I ran the original program which came with the router way back and that isn't working either.
View 1 Replies View RelatedHow do I enable the Security Mode on a Dling 615 wireless router?
View 1 Replies View RelatedHow do i enable security for my wireless WRTP54G?I
View 1 Replies View RelatedI have ASA 5585 with SSP20. I want to enable same security level subinterfaces (routed mode) to communicate with each other.
I have put below command at global level but somehow it is not happening.
hostname(config)# same-security-traffic permit inter-interface
Do I also need to check for NATing or some other things apart from above command?
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies View RelatedSo, I have this router at home a WRT150N. I put in access restrictions so my siblings won't stray onto unwanted pages.I enabled SPI Firewall Protection and what do you know, it worked. The next day though, we didn't have an internet connection.I checked everything with the modem (power cycles, etc.) and then I tried the router. Upon disabling SPI Firewall Protection, the internet connection came back.I tested it yet again, to see if it really was the SPI. Enabled and bam, no internet access again. I made sure to select "Allow" in the Access Restrictions for "Internet access during selected days and hours" making sure also that "Everyday" and "24 Hours" are selected.Now my question is, what do I need to do in order to enable my Access Restrictions without having to lose internet connection via the SPI Firewall?
View 2 Replies View RelatedI am switching out our old WRVS4400 router to the Cisco 891. Having a problem configuring the Cisco 891 router. I changed the V LAN port on the 891 from 10.10.10.1 to 192.168.2.1 and the ip address saves but when I try to rediscover it through the CCP to the new Ip address 192.168.2.1 I get the message discovery failed.
The sub net mask I used is 255.255.255.0 The only thing connected to the 891 router is our linksys 48 port switch which is SL248G and my laptop is connected to the switch. The port its connected to is FE LAN 0 . How do discover the 891 so I can do further configuration and to enable the FE8 port for using it for our internet connection?
I've installed version 4.8.02.0010 of the VPN client onto a Dell Latitude D820 laptop. When I attempt to connect, I get this message. There are no firewalls running (I disabled the Windows XP firewall) and I'm running under Service Pack 2 with all of the latest security patches from Microsoft.
I even tried un-installing the client and using an older version (4.8.00.0440) and it reports a similar error in the Log file.
I'd prefer to NOT have to wipe the laptop and reinstall the O/S if I don't have to. This is the only laptop that I've experienced this problem with but it's also the first Dell Latitude D820 that I've attempted to install the client on.
Is there a problem with the Dell Latitudes and the VPN Client? Is there another way around this other than a wipe and re-install?
how do i enable port forwarding on the CLI for ASA 5510. outside subnet is 192.168.1.0/27. when i try to ping another IP with that range i can't access.
View 37 Replies View RelatedI am trying to configure a 3750 48 port switch and having trouble with getting it to see the sfp. I just want to set up the router with a pretty basic set up since I am using it for a ping test between 2 buildings, via fiber. How I can enable the sfp port?
View 3 Replies View Relatedi want to enable a port 7000 and 514 on my cisco 851w router. using the command-line?
View 1 Replies View Relatedi want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View RelatedHow do i enable my desktop computer to recognise my wireless router using the ethernet port
View 2 Replies View Relatedhow to enable protection path in GSR 12404 router Gigi interface connected to mux port. Like we configure APS group for POS interfaces.
View 1 Replies View RelatedOne of our clients just installed a new security system and they need to be able to view the cameras from outside the network. According to the vendor, we should only need ports 81 and 2000 forwarded to the internal DVR on both TCP and UDP. They really aren't much troubleshoot the network config.
ASA Version 7.2(4)
!
hostname ciscoasa
domain-name ********
enable password ******** encrypted
passwd ******** encrypted
[code].....
I was wondering if there is a workaround to have a mac access-list bond to a port security violation action our need is the following: we have a range of 10 mac addresses that can use any port on the 3750, we only want to allow those ones yet we also need to tak action if a denied mac appears on any port of the switch.the only work around I found is to basically go into a port-rage mode and list all the allowed mac addresses under all the ports of the switch. I would also add to that a port violation action. did not test it but should work. problem is, it would be a huge config.I did read that we can create a mac access list and then bind that mac to physical ports wich will actually simplify our solution yet I did not find a way to bind the mac list with a port violation action.
View 1 Replies View RelatedI have installed CSA on windows 7 with rule to block rpc port 135.But when i am scannig this host, this port is still opened.I changed OS to Win Vista,Win7 x86, but there is no changes.Is it possible to block port 135 using CSA on windows 7?
View 2 Replies View RelatedWas wondering how to set port security on the 881. I have all the FE ports shutdown except one and want to limit that port to one specific MAC address.
View 7 Replies View Relatedhow to perform port security or mac access-list on LAN ports of router 861 or 881.There are commands access-list 700-799 , but I don't know how to apply that access list on configured vlan or particular port.
View 1 Replies View Related