how to perform port security or mac access-list on LAN ports of router 861 or 881.There are commands access-list 700-799 , but I don't know how to apply that access list on configured vlan or particular port.
View 1 RepliesI am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
View 12 Replies View Relatedi configurated Ipsec vpn at asa 5510.
my inside ip 192.168.10.156
my public ip: 85.x.x.x
my peer ip : 62.x.x.x
the project is that:the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
my inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.i do that way but i can not test it.
interface Ethernet0/0
nameif outside
security-level 0
ip address 85.x.x.x.106 255.255.255.248 standby 85.132.71.107
!
[code]....
I am trying to allow telnet to port 551 but i couldn't get it to work.I am using a cisco 1720 router running on IOS 12.2.I am using the below commands to set the access list to allow access to port 551 using remote telnet to the Cisco router.hostname R1!interface ethernet0ip access-group 102 in!access-list 102 permit tcp any any eq 551.After i enter the above command the router will disconnect me and i will not be able to connect to it for awhile. Once the router is up i am still unable to telnet to port 551.
View 14 Replies View RelatedI was reviewing some old configs at work today and noticed somthing weird in the access-lists. What is this?
View 6 Replies View RelatedI have a layer 3 switch, 3550.I have several vlans on there just for playing around with. One of the vlans, has a vonage linksys box attached to it with a UK number attached. From time to time telemarketers call at 03:00 in the morning, this as I'm sure you can imagine is not much fun. The linksys box gets 192.168.3.3 as it's ip.The switch is connected to a non cisco router at 192.168.0.1
interface FastEthernet0/24
no switchport
ip address 192.168.0.2 255.255.255.0
I was thinking a time based access list would work best I have tried several variations but the phone still rings. I have tried access-list 1 deny host 192.168.3.3 permit ..... and more extensive lists but the phone still rings. I have not applied the time-range yet, so that's not the problem.I have applied the list to the vlan interface and to fa0/24 but it's not working.
I want to block the sql port access of my server to all except few of my ip addresses while access list on Cisco Router IOS how do i do that.
View 3 Replies View RelatedI configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
I need to know the maximum number of MAC addresses that can be entered in to the MAC security filter list on the AP541N.I know it has a maximum number of 200 concurrent users, however the documentation does not specifiy whether this also applies to the MAC filter.
I have used wireless acces points in the past that allow hundreds of users but only allow 64 MAC addresses, so this is very important.
What are the list require for setting up Data Center for either University or Government?
View 4 Replies View RelatedI'm using LMS 4.0.1, migrating data from 3.2. When I select My menu, My dashboards, Functional (or any other view) I can get a list of non deployed port lets.
View 2 Replies View RelatedAm I able to use an SSL cert in the proxy list for the same VIP but on a different port?
View 1 Replies View RelatedI'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies View RelatedWhy is my WRT54g router only showing the 1st LED port is lit, and not the rest when I have changed or added a device to the 2nd,3rd,4th port? It is also stopping my ability to stream,view youtube etc. When I disconnect the router from my cable provided modem, everything works fine?
View 2 Replies View RelatedIf i fully populate all switch port (Cisco 3750 series) with 100 filter list on each port is it recommendable.
View 4 Replies View RelatedHow to implement mac access-list in 881 and 892 router ? As you now that we can get additional switch-port in the same router but I can't see the function in this router. I guess the switch port must function like the catalyst 2960 switch.
View 3 Replies View RelatedI'm creating an access-list that will contain all networks and host that will be redistribute into EIGRP.Till now, this access-list contains 72 entries but this number can increase anytime.
I'm using a 3750-x layer 3 switch, and I'm wondering how big this access-list can be, regarding CPU and memory utilization and performance.
we installed a cisco router in a school with two vlans (VLAN 1 & VLAN 2) VLAN 1 is for teachers and Admin and VLAN 2 is for students. We want so that VLAN 2 shouldn't be able to access any device in VLAN 1 but VLAN 1 should be able to access all devices in VLAN 1 & 2
VLAN 1 192.168.11.0/24
VLAN 2 192.168.12.0/24
I am using VLAN interfaces. I know we have to use some access lists but if i apply
access-list 100 permit ip 192.168.10.0 0.0.255 any
access-list 100 deny ip 192.168.12.0 0.0.0.255 192.168.10.0 0.0.0.255
With this access list two subnets can not access each other. How these access list should look likes ?
Creating an Access Control List
View 2 Replies View Relatedso far i also knew that if u assign an access-list to an interface:
for example:
int vlan1
ip access-group 150 in
and the access-list does not exist in the configuration it will block everything meaning it will be an implicit deny empty access-list but lately i've noticed on new routers that its different,if i assign an acl to an interface where the acl doesnt exist in the configuration it acts as permit all,
this is a project and my configred file:I can't config access list according to the project.
View 19 Replies View RelatedHow to apply access list on Vlans ?
my Scenario is
13 Vlans in cisco 3560 switch (Vlan 10,20,30........ 130)
vlan 10 ---- ip range 192.168.10.0/24 interface vlan 10 ip add : 192.168.10.1
vlan 20 ---- ip range 192.168.20.0/24 interface vlan 20 ip add : 192.168.20.1
here i want to block vlan 10 access to vlan 20 i created extended access list deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
and applied in interface vlan 10 as out now i cant able to access any host in vlan 20 (host 192.168.20.1) but i can able ping vlan 20's gateway 192.168.20.1
I have a question about access-lists on ASA: (5520 running 8.4)Often I want to permit all traffic from networks behind an interface (let's say DMZ in this example) to Internet, but NOT to internal networks. Then I first configure a Deny from DMZ to all internal network and then a Permit to ANY. If I forget the first Deny I will allow all traffic also to my internal networks. Is it possible to configure an access-list that permit all traffic from a network to all networks that are reachable via a given interface? In this example: Permit all traffic from DMZ to all networks that are reachable via the Outside-interface? This should permit traffic to Internet and deny traffic to internal networks in one statement.If I specify the outside-interface as the destination only traffic to the interface itself will be allowed.
View 1 Replies View RelatedI reported a really strange issue on a Cisco Router 3945. Here below info about release software used: [code] Please look at a brief extract of router running configuration file: [code] It’s an easy configuration of Extended ACL and the application on an Ethernet interface. The expected result is:
- The interface works properly (because access list is permitting every kind of data traffic in input)
- Checking “show access-list 180”, the counter of matched packets increments for all the packets that are forwarded inside the fa0/0/1.
But actually the Fastethernet 0/0/1 drops all the packets as if all the packets don’t match with access list (And this behavior is really incredible). The interface couldn't be used anymore because any kind of data traffic is denied.
I want to block access of some clients from the vlan1 to acces internet blocking their MAC address. How can i do this?
I have tring this way:
access-list 700 deny mac address 0000.0000.0000
access-list 700 permit 0000.0000.0000 ffff.ffff.ffff
int fa00
bridge-group 1 {input-address-list 700 output-address-list 700}
but it's not working .
I am having a problem getting this to work and I have always done it with 2 Static ip address. but now this company changed to 1 and I am doing something wrong.
I have comcast with 1 static IP, I have a local LAN with 6 host and 1 server that does Mail and remote access and web traffic.
I need a config that allows me to use 1 static ip on the outside interface of the PIX and allow with an ACL 7 ports open to the server and allow all the local host out to the internet.
I'm new to this forum and Cisco in general but I feel it may be very resourceful to me as I am a new network administrator fresh out of school for a local credit unionHere's my situation:We need to limit access to one of our servers to only 3 workstations used by our IT department. The server is on a Cisco 3560G on port 17, which is the interface I'm trying to apply a standard, basic ACL to, which looks like this:
View 10 Replies View RelatedI've been working on an application recently that practice ACL configuration, and since finishing I figured it should be put on the internet as there wasnt much more work to do to make it suitable for a website. It allows you to practice both standard and extended ACL configuration by generating a random number of ACL actions for you to configure, and provides the correct config to compare yours against to see if you were correct. It also emulates a router at a very basic level to allow practice when there is no equipment available.
View 9 Replies View RelatedI have an extended acl on my VLAN interface in bound and it is working like I need it to, securing one side of my network from the other allowing only what I want from my desktops to my servers. The acls look something like this:
vlan70 -----> inbound acl (allows 80/443) ---> vlan100
I need vlan100 to have access to something on vlan70 now and I cannot get it to work. My question is would this work?
vlan70 -----> inbound acl (allows 80/443) ---> vlan100
vlan100 <----- outbound acl (allows 9100) <---- vlan70
Traffic is initiated from vlan100 not from vlan70 then back through so an established rule does not work. Also there are many more ports open in my inbound acl but this is simplified for ease of reading.I want to make sure if I place both an inbound and outbound rule on my vlan and that it is in the right place, both on the same vlan.
I have a router in front of a few firewalls on an internet link. All traffic from the inside network must go through one of the firewalls to get out through the router and similarly there is a dmz on one of the firewalls.I am trying to make sure the router is fully hardened.Should I apply an access list on the outside interface of the router along with the access list for management access?
View 11 Replies View RelatedI have a sip gateway (AS5400) that is used to connect sip providers to our internal voice network.Internal gateway (10.1.1.2 LAN) -- SIP trunk -- AS5400 (10.1.1.3 LAN/ 8.23.23.43 WAN) -- SIP trunk -- Internet SIP Provider We encountered the following problem :A SIP call from internal gateway to the sip provider could establish but was muted on our side (sip provider could hear us)On the WAN interface of the AS5400, there is a ACL that filter traffic IN coming from SIP Provider
interface GigabitEthernet0/0
ip address 8.23.23.43 255.255.255.224
ip access-group 101 in
I log the deny on this ACL and I saw some udp packets denied with LAN addresses !*Mar 3 15:24:44.001: %SEC-6-IPACCESSLOGP: list 101 denied udp 10.1.1.3(0) -> 10.1.1.2 (0), 1 packet I did not bind anything on the sip config.When I changed the ACLs, calls went well.Why do I see LAN packets on the WAN interface ?
I am trying to create a user restriction to allow one user to access only two networks (10.192.3.0 and 10.192.5.0) I have range of networks but I want to permit only two networks for limited user and full access for the admins. I know this was possible with ACS 3.3 but I am not too sure if this is also applicable with ACS 5.2.
View 1 Replies View RelatedI'm configuring Control Plane Police in a Catalyst 6509. This equipment is using IS-IS like its IGP routing protocol, and iBGP. In order to make CoPP work Im classifying the traffic entering the control plane like CRITICAL, IMPORTANT, NORMAL, UNDESIRABLE and DEFAULT. Obviously routing protocol traffic must be classified like CRITICAL. Doing so is easy to BGP because it runs over TCP/IP and I can configure the following access list to classify BGP:
ip access-list extended CP-CRITICAL-IN
remark #### CONTROL PLANE CRITICAL TRAFFIC INBOUND ####
remark #### ROUTING TRAFFIC - BGP ####
permit tcp host [BGP neighbor addr] eq bgp host [local BGP addr]
permit tcp host [BGP neighbor addr] host [local BGP addr] eq bgp
deny ip any any
But IS-IS is also a CRITICAL traffic, but IS-IS doesn't run over TCP/IP, rather it exchange its own PDUs. So, how do I classify IS-IS traffic with an access list?