One of our clients just installed a new security system and they need to be able to view the cameras from outside the network. According to the vendor, we should only need ports 81 and 2000 forwarded to the internal DVR on both TCP and UDP. They really aren't much troubleshoot the network config.
I am trying to setup Internet based CCTV system on a router that has a VPN network in place. Am i able to forward the Media and Web Ports to the router without interfering with the current VPN settings.
I have a Cisco home rack lab which is behind my ASA 5505. I use my ASA to connect to the internet. My situation is I travel a lot for work, and I am unable to do my labbing practice. I am pretty new to ASA and would like to do a port forwarding to access my access server which is connected to my Cisco routers and switches.My network topology is this: (internet)-------(ASA 5505)----------(3550)-------(CM32 Access Server)----------(Cisco Rack) This is how I setup my remote access:
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
I have a Linksys WRT610N wireless system with WPA-PSK security and this works fine with several computers but now one computer detects the wireless security as WEP and can thus not connect to the router. I have tried to manually connect to the router with correct security WPA-Personal (TKIP) and correct password but then the computer says "settings saved on this computer for the network do not match the requirements of the network".How can I get the computer to detect the correct security? The computer is running Windows 7 home premium.
how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
Region : UnitedKingdom Model : TD-W8970 Hardware Version : V1 Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
I want to create a Counter Strike Server and need to open some ports for that.The Problem: I cannot seem to open the ports for gaming.The Modem Setup: My Firewall is disabled.My guess is that, this is the area with the problem. I guess my modem is not forwarding onwards.The Problem: I tried checking my ports with websites like URL etc.It cannot access my port.
I have a links wireless system, I am trying to make this a secure connection. I have gon into the property settings and everytime I try to set the security to wpa2 or even wpa it I lose my internet connectivety. I can't get the security key needed.
I have Wi-Fi on my smartphone and I want to set up another lap-top and it is asking for a security key, where do I find it ?I already have one lap-top set up !
I have a DSL-524B from D-Link. My problem is, whenever I Port Forward port 80 to my comp's IP to host a web server, all the other computers connected to the router are unable to access the Internet. So, I set up no-ip to use port 8080, but, this exposes my ip and even when masking, if you look at the HTML code, you get the ip.I need to know how to open up port 80 without restricting Internet access to only my comp, or any other work around.
I have an older D-Link DGL-4300 wireless router, I've purchased a wireless home security system and can't seem to get the 2 connected. I've tried resetting the router & modem (powering down & waiting from 1-5 minutes), and my router just won't read the port that I've plugged the security system ethernet cable into.I think the problem is my firewall but I don't know how to set it to allow the router to read the port that I've plugged into, or it could be the firewall that my anti-wirus has or possibly both.My equipment is Comcast cable, router (as noted above) and a D-Link DCM-202 modem, Windows XP 3, and Norton anti-virus. Now I also have my phone through Comcast and it has it's own modem.
I keep getting a pop-up message from my firewall ( Sygate personal -free ) telling me that NT Kernel and system has been blocked. I checked the box to say don't show this message again, it still shows it every time. minutes in between. It freezes my pc and screws up any typing i'm doing at the time. According to the application list it is checked to allow and running.It is not listed in Task Manager.
A N600 Router Model F9J1102v1 router first installed in July 2012 with WPA-PSK, MAC Address Filtering and "Self Healing" enabled would not allow a new PC to connect via an RJ45 port. Belkin support ask for the unit to be reset to factory settings which is done and the Security system re-enabled again. Valid MAC Addresses start to be added and midway a PC is discovered in the Network without its MAC address added. Closer scrutiny reveals that another unknown device has also found a way into the router and that the 'Block' option on the MAC list is also failing to work. Anyone think of what one should do with this security shambles other than turn the thing off quick?
I'm building a security camera system,which can connect to internet to be viewed from away.The camera receiver connects to the modem with a Cat 5 ethernet cable,which results in a cable running across the room. My modem is a wireless type,but the camera receiver only has cable support it seems.
Is there a device that I can use to get rid of the Cat5 cable in this scenario?
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
I want to know which is the port used by my system on accessing a particular URL.Suppose the URL is ip_address:9081/abc.Is the software port 9081 of my system is being used to access the URL? How can I identify it? Is there any command to identify the used port for a particular URL?
I have a 3750 switch stack running version 12.2(53)SE2 IPBASEK9-M. I have dot1x configured on the switch and have a Windows 7 PC connected with 802.1x configured on the interface. I see the EAPoL start message from the PC, but I don't see any RADIUS packets from the switch to the RADIUS server. I have a simple dot1x config just to try to get it working prior to adding additional features such as guest-vlan...
Config and debug file attached.
I don't know if the ip dhcp snooping and arp inspection configuration is causing an issue with this or not. I see the EAPoL packet received on the switch as seen in the debug attachment, but I still never see the RADIUS packet. I did set both to trust on the interface but still the same outcome. I can't disable it since it is a production switch with a test interface.
I finally got my Cisco Pix 501 working on my network and everything is working great! However, I do host game servers on occasion and I have a 24/7 FTP server up and as of now, I can't connect to it because the PIX is blocking the ports!I have zero experience with Cisco, so I need step-by-step instructions on what commands to enter to get this thing working!
I am very confused now. I got my 5505 for home (basic) and loaded up 8.4(1) fresh. From the inside interface I can reach the internet no problem but I am having issues trying to get my port forwarding to work with torrent. inside host is 10.100.130.5 port is 26883, I have been trying to configure this forever.
I finally got my Cisco Pix 501 working on my network and everything is working great! However, I do host game servers on occasion and I have a 24/7 FTP server up and as of now, I can't connect to it because the PIX is blocking the ports!
We have the above router for a small business and I want to configure VPN to port forward to the server so it can handle the VPN traffic through Routing and Remote Access.I have configured port forwarding on SMTP, RWW and other protocols successfully but VPN will not work.Within the built in web interface on the Cisco it advised that if I want to configure VPN I need to use Cisco Config Pro. I have had a look through this software but it looked to only support the router as the VPN gateway rather than port forwarding to a server.
I have recently purchased a Cisco 871 router. In the GUI from the installed software, I have been able to configure which ports are forwarded to a specified IP address within my local area network. This seems to output a configuration line like this:
However, I can only do this one port at a time. Is there a function or command that I can use to specify a range of ports? For example, I would like to forward tcp ports 1000-2300 to the IP address 192.168.1.123
I was at a friend's office today trying to get the IP cameras working but forwarding the ports seems not to work with his current modem from ATT (a Westwell F90 or something). Would the workaround for this be purchasing a third party modem instead that supports port forwarding and stop leasing the Westwell F90 from ATT?
edit: the modem is hooked up to a DI-524 from D-Link and i already forwarded different ports to see if it was specifically port 80, 1024 etc
I've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
