I want to know which is the port used by my system on accessing a particular URL.Suppose the URL is ip_address:9081/abc.Is the software port 9081 of my system is being used to access the URL? How can I identify it? Is there any command to identify the used port for a particular URL?
View 1 RepliesI'm new to networking and was looking for some assistance. First off im using packet tracer to diagram my senario as I will be receiving my equipment next week to deploy.
Hardware to be used:
1. 2 catalyst 3560 switches
2. all connect to a sonic wall router
I have two companies that work in the same office space. I need to keep these companies seperate on their own vlan. They will however need to share the phone system.(Packet tracer file uploaded to give those who have the time to see what I put together.) [code]
I am trying to setup Internet based CCTV system on a router that has a VPN network in place. Am i able to forward the Media and Web Ports to the router without interfering with the current VPN settings.
View 4 Replies View RelatedOne of our clients just installed a new security system and they need to be able to view the cameras from outside the network. According to the vendor, we should only need ports 81 and 2000 forwarded to the internal DVR on both TCP and UDP. They really aren't much troubleshoot the network config.
ASA Version 7.2(4)
!
hostname ciscoasa
domain-name ********
enable password ******** encrypted
passwd ******** encrypted
[code].....
I've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies View RelatedWhat key sequence to go into ROMMON mode from the console port for VSS system with 2 VS-S720-10G?
View 3 Replies View RelatedRecently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies View RelatedI have setup a network of 5 windows xp systems. All the systems can access one another except for one system which cannot access any other system although it can see the other systems in the workgroup. It can ping to all the systems.The error message is \computer is not accessible. You might not have permission to access this network resource. Contact the administrators of this server to find out if you have access permissions. Th server service is not started.But i checked that the service is running on all the systems.
View 7 Replies View RelatedActually i have a small network of 4 and 5 computers. i am sharing internet via lan not ICS.there are some computer showing me in my network places coz i am using windows 7 and the other computers have same window. i can ping their computers by name and by ip add, which is assigned by DHCP. i can see thir MAC address. can i access their computer i mean their data or something else. i don't know that this is the right place to share such information or not.
View 14 Replies View Relatedi have server 2008 machine..how can i access windows 7 as client system?
View 1 Replies View Relatedi can ping the other system but i can not access tthat system.. error message shows that path does not found.
View 6 Replies View RelatedA I went over to a friend's house to fix some problems with his computer. He has a Windows XP Home Edition desktop. I used System Restore to fix some kinks with it, and now the computer has no Internet access, and I have no idea how to get it back. I tried reversing the System Restore and turning it off, but that's not working. They said that the connection was fine, but that the computer could not read the modem.
View 1 Replies View RelatedIs there any way we can assign or access multiple system with 1 public ip to save public ip's.
View 5 Replies View RelatedHow can i access a cd rom from another machine in a wireless network while both machine using ubuntu linux
View 1 Replies View RelatedI am trying to connect to my office PCs via VPN and/or RDP. The office uses Qwest DSL and has a dynamic IP address. I use DynDNS.org to keep the DNS updated with the WAN address of the router. However, any attempt to access the network fails. I have tried remote management access (I enabled it on the router) but that fails. I forwarded RDP ports on the router to one of the PCs but can't connect to it. I also set up a VPN server but cannot connect to it either. Something tells me that all requests to myoffice.homeip.net are not getting to my modem/router. I have even tried the IP associated with the name (Yes, I did check that it is correct!) but nothing works there either.
View 1 Replies View RelatedMy task is to plan out on how to setup a WiFi Access System in our college.There are more than 3000 users which include students, faculty, etc.Area is spread across almost 1 acre of land area.
Q1. How do I go about setting up a system where MAC based WiFi Access system is achieved?
Q2. What equipment will be needed, like routers, access points, etc.?
Q3. How many Access Points will be required, and which will be the best in terms of cost, range, speed and performance.
Q4. Which would be the best equipment for this?
Q5. User management solution?
I'm having trouble accessing system files from my XP machine through my Windows 7 network. This is the error that I get: "Network Error Windows cannot access \xpusercwindows
You do not have permission to access \xpusercwindows. Contact your network administrator to request access."
I'm admin on both systems(home). Even after searching online, I still haven't come across a solution to my problem.
how do i browse network systems drive without having local admin password
View 1 Replies View RelatedI need to extend the wireless range over what I have using an E2000. Can I use a WAP610N in repeater mode? If not can I use a WAP54G knowing that there will be a performance loss? Is there another option to add additional coverage to the existing wireless network?
View 2 Replies View RelatedIn my log I have the message: "Access denied to wireless system with MAC address 0020008E971E". When I checked the vendor for this MAC, it shows Lexmark international inc, which fact make me feel something is wrong. My first thought was that somebody trying to break into my net but I am close to accept that the owner of Lexmark WiFi printer without an idea in networking, just tried to connect it to his network and after failing to do that, it's wired and wireless features are still on. But still could this be bug or something? I am posting some logs when I first discovered the problem and after I granted access to the device with the MAC address 0020008E971E. I forgot to tell you, that before I decided to post here I did firmware upgrade from Hardware version A3 1.10 to 1.35NA (I bought it from US) with factory default restore. The result was absolutely the same - the messages kept coming "Access denied to wireless system with MAC address 0020008E971E". So I granted access to that MAC and checked the logs again. There is a line in the log that stated "primary:"
View 7 Replies View RelatedI have a netwokr in which users are getting ip address from DHCP server that is window server.i want to block some users to access interent by using their device mac address.i have these devices in my network...
2921 cisco cme router
cisco 2960 switches
cisco 892 cisco internet router
internet ADSL that cnnected with cisco 892...
wireless AP 1142...
i have no firewall or any asa...how can i block some users for accessing internet but they can access internal network...for file sharing and prinitng,...
Just started using our ASA 5505 v8.2 (1) Trying to configure the ASA appliance to allow access into an internal resource (i.e want to be able to RDP into a system behind the ASA from the internet).I have used a static NAT:
static (inside,outside) 100.100.100.2 192.168.1.28 netmask 255.255.255.255
access-list OUTSIDE extended permit tcp any host 100.100.100.2 eq 3389
When I view the logs it is reporting the following:Inbound TCP connection denied from 206.100.100.1 (external IP) to 100.100.100.2 /3389 flags SYN on interface outside.Been pulling my hair out with this one as I believe I have everything configured correctly.
I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
View 12 Replies View RelatedI have Dell Inspiron 15 3520 laptop bought in December 2012 with Windows 8 Pro. It was working fine until two days ago. I am unable to obtain DHCP lease either through wireless or wired network. After troubleshooting, I found DHCP service is not running and try to restart but of no avail.I ran sfc /scannow and the results are OK.
View 2 Replies View RelatedI have a 3750g connected to a "core" switch stack of 7 other 3750g's via 2 GigE ports in a trunk. This is currently in a switchport mode access port- channel so only the default vlan data is sent over. Now we have a need due to physical location of these switches, to allow vlan20 (DMZ) from this 3750g to the switch stack. I will configure a few ports on the switch stack for vlan20 and they need to be able to talk to the stand alone 3750g.To do this I will change the port channel on both endpoints to
-switchport trunk ecapsulation dot1q
-switchport mode dynamic desirable
also making the appropriate change on the interfaces belonging to this trunk.My question is, now that its a trunk port that carries multiple VLANs, how much is the bandwidth reduced on that 2gbps link?I have a very active VLAN (10) on the stand alone switch, but on the core I'm not going to be assigning VLAN 10 to any ports. So does traffic from VLAN10 even come across the trunk (wasting bandwidth) if no ports on the core side are assigned to it? I really just need vlan 1 and 20 (for now).
I want to create a Counter Strike Server and need to open some ports for that.The Problem: I cannot seem to open the ports for gaming.The Modem Setup: My Firewall is disabled.My guess is that, this is the area with the problem. I guess my modem is not forwarding onwards.The Problem: I tried checking my ports with websites like URL etc.It cannot access my port.
View 1 Replies View RelatedI'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies View RelatedI am trying to allow telnet to port 551 but i couldn't get it to work.I am using a cisco 1720 router running on IOS 12.2.I am using the below commands to set the access list to allow access to port 551 using remote telnet to the Cisco router.hostname R1!interface ethernet0ip access-group 102 in!access-list 102 permit tcp any any eq 551.After i enter the above command the router will disconnect me and i will not be able to connect to it for awhile. Once the router is up i am still unable to telnet to port 551.
View 14 Replies View RelatedI was reviewing some old configs at work today and noticed somthing weird in the access-lists. What is this?
View 6 Replies View Relatedrecently my brother has blocked some ports on our home router because he thinks i play too much video games. ( i actually dont play a lot ! ). He says there are alternative ways to make it work again and challenges me to figure out how to change the ports back to normal but he would not give me the access to the router, meaning i dont know the Login and password for it. Plus I am not allowed to reset the router to factory settings. For about three days I have been looking up ways to change the ports on my router through my computer but nothing has worked so far. I have a gaming tournament coming up and I really need to practice with my team but i cant get access to it.below is my system's information,
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: AMD A6-3400M APU with Radeon(tm) HD Graphics, AMD64 Family 18 Model 1 Stepping 0
Processor Count: 4
RAM: 3560 Mb
Graphics Card: AMD Radeon(TM) HD 6520G, 512 Mb
Hard Drives: C: Total - 468745 MB, Free - 420932 MB;
Motherboard: ASUSTeK Computer Inc., K53Z
Antivirus: None
I connect to switch Access Point, configure port on switch which vlan work on this port. But after reboot AP my config for this port delete and have other config where vlan 1 untagged, and allow all other vlan. But in my cinfig allow 3vlan: untagged 100, and tagged 113, 999.
View 1 Replies View RelatedI already configured my LAN connection to only have an IP address, and a subnet mask, leaving default gateway blank
View 3 Replies View RelatedI got one request from one of the user to allow his ip to access one public using port www, this needs to be allowed in Cisco PIX, if the below command is correct for this.
Source host : 10.84.11.1
Destination IP : 203.126.112.131
Port : www
access-list acl_outbound permit tcp host 10.84.11.1 host 203.126.112.131 eq www