Cisco WAN :: 1921 - IOS Upgrade With Security License?

Nov 4, 2011

I have a Cisco 1921 ISR Router with Security License running software version 15.0. I want to upgrade the router to 15.1. But I don't want to lose the security license that came with the router. When I look at the IOS downloads page on Cisco, all I see is universal images for all versions of 15.1.
 
My question is - where is the security license stored? In the IOS or programmed in somewhere else of the router? If I upgrade my router to one of the newer 15.1 universal images, will I lose my security license?

View 2 Replies


ADVERTISEMENT

Cisco Firewall :: ASA 5505 Security Plus License Upgrade?

Apr 19, 2012

We want to upgrade one of our Cisco 5505 with Security Plus license. what is the difference between L-ASA5505-SEC-PL and ASA5505-SEC-PL upgrade licenses?

View 1 Replies View Related

Cisco WAN :: Upgrade License 1941-K9 From IPBase To Security

Oct 25, 2011

I would like to Upgrade license Cisco 1941-K9 from ipbase to security

View 5 Replies View Related

Cisco Security :: ASA 5545 - 8.6 - Active / Standby - License Upgrade

Feb 4, 2013

We are planning to upgrade the ASA license in an A/S pair by adding the ASA5500-SC-20= license. The ASA is 5545 and runs 8.6. According to documentation, after 8.3 version, the ASAs can share a license features and do not require the same license on both boxes. I run a test in GNS3 with 8.4(2) images and I saw that by adding the 'activation-key' command only on the primary unit did the job as the 'show activation-key' output shows. In order to be 100% sure would like to verify the following:

Putting the activation-key only on the primary unit is enough and there is no need to do anything elseIn case the primary unit is standby, again we have to put the actication-key command on the primary unit (I am asking this because the 'activation-key' command is not listed under the commands that are not replicated to the other unitk, but doesn't make sense to be replicated since the activation-key is 'tied' with the S/N of the device).

View 4 Replies View Related

Cisco Switching/Routing :: License Upgrade In 2900 For Security K9 Feature?

Dec 18, 2012

i have 2921 router with base license . i want to upgrade to it to security k9 feature or want to enable it. i have license file with product activation key. how should i do it. if any body have screen shot file

View 1 Replies View Related

Cisco Firewall :: Difference Of VPN Plus License And Security Plus License ASA 5520

Oct 16, 2012

What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.

View 1 Replies View Related

Cisco VPN :: 1921 - Converting PAK Into A License

Sep 6, 2011

I have purchased a PAK for my 2 cisco 1921 routers .I would like to to configure IP SEC or SSL for VPN connectivity on the routers. How do i convert the PAK into a license?

View 1 Replies View Related

Cisco WAN :: Install License On 1921 With USB

May 12, 2013

how install a .lic file onto the new Cisco ISR G2 1921?
 
I know how to install via tftp, however I need to know how to install from USB.

View 4 Replies View Related

Cisco WAN :: 1921 License Is Showing Active But Not In Use

Apr 16, 2011

i purchased 1921 with ipbase license , then i installed security 60 days trial license in it.the license is showing active but not in use and in the sh version also is not showing.then i used some command like boot using security bundle then i restarted the router , after that i am getting the following the message "loadprog bad file magic number 0x0 boot cannot load flash".then i tried to upload from tftpdnld using rommon mode then i am getting following error "Interface GE 0 link down TFTP: Operation terminated prematurely in rommon mode".

View 2 Replies View Related

Cisco WAN :: After Installing Data License In 1921 Router It Does Not Show?

Dec 13, 2011

i installed Data license(Evalutation) initally it took the license after reload, when i enter sh lic command the out put shows that Data license is installed and valid for...
 
But when i run sh ver command it only shws ipbase license and not the data license

View 1 Replies View Related

Cisco WAN :: 1921 - Special License To Utilize Balancer / Failover Feature?

Apr 21, 2013

Lately we have been comsidering an upgrade in our organization involving a 1921 router. The main role it will play is a load balancer/failover between 2 connections from 2 different ISPs. what additions are required to be added to this piece of equipment to make the configuration work. Im researching the matter now and it seems an extra card whould be purchased in addition to the router. Also, i cant seem to find much information on the available licenses to go with the router. will i need a special license to utilize the balancer/failover feature? (ip base, data, SEC).

View 2 Replies View Related

Cisco WAN :: 1921 IOS Upgrade Failing

Mar 31, 2013

Any issues upgrading the IOS on a 921 router.How can i create a certificate for the new IOS? I've never had to do this for other IOS 15 upgrade?I've confirmed the IOS is not corrupt and if i upgrade the router in ROMMON the router boots correctly.

View 1 Replies View Related

Cisco WAN :: Possible To Upgrade 1921 Router

May 3, 2013

I am really stuck with router requirement for one of our client. I need 891 SEC router. I think this comes with advanced IP services. What I have is 1921, with IP Base. can I upgrade 1921, so it will become alternative to 891 SEC.

View 1 Replies View Related

Cisco Switching/Routing :: Upgrade IOS From 1921 ISR?

Dec 18, 2012

How I can upgrade the iOS from CISCO 1921 ISR? Without losing my configurations.

View 3 Replies View Related

Cisco VPN :: Upgrade SSL License For ASA5540?

Apr 2, 2013

I have ASA5540 with 1000 SSL-VPN License, then I would like upgrade from 1000 to 2000. Which part I have to add between
 
L-ASA-SSL-1000= 
L-ASA-SSL-1K-2500= 
ASA5500-SSL-1000=

View 1 Replies View Related

Cisco :: WCS V.7.0.230.0 To NCS 1.1 Upgrade Not Accepting License?

Nov 15, 2012

We are currently preforming the upgrade from WCS v.7.0.230.0 no NCS 1.1. When we select the Lic file we get an error message "Unable to add any license without an NCS (L-NCS-1.0-K9) license." The file name is WCSUPG20121115142018448.lic.

View 2 Replies View Related

Cisco VPN :: 5505 - SSL License Upgrade?

Aug 11, 2011

My client is having a 5505 which supports 2 SSL peers as per now and we want an upgrade . I had a look into GPL and I was confused with two of the following part numbers . Which one should I go for as both of these look same for me and there is a huge difference in price .
 
ASA5500-SSL-10
ASA 5500 SSL VPN 10  Premium User License
ASA-AC-E-5505
AnyConnect Essentials VPN License - ASA 5505 (25 Users)

View 4 Replies View Related

Cisco Firewall :: Unable To Upgrade Pix-525 FO License?

Feb 10, 2012

Not  abe to upgrade the IOS image PIx7.0  from earlier version 6.3   in  to my old Pix-525 FO(Secondary unit) license box .
 
Is it possible to upgrade without Primary unit (Unrestricted License)  ?

View 6 Replies View Related

Cisco Firewall :: Upgrade License On ASA 5510?

Oct 12, 2011

I have a two ASA HA and I'd like to upgrade the license to ASA5500-SSL-250. I need to know if i have to purchase one license (ASA5500-SSL-250) for the Active unit and one license  (ASA5500-SSL-250) for the standby unit.

View 3 Replies View Related

Cisco Firewall :: ASA5505-SW-10-UL - How To Upgrade License

May 10, 2011

I want to confirm if the upgrade license (ASA5505-SW-10-UL=) is backward compactible with PIX 501 firewall device? though pix 501is end of life bit i want to verify if the upgrade license for asa5505 will work with it?

View 4 Replies View Related

Cisco Firewall :: ASA 5505 License Upgrade

Dec 17, 2012

I have a Cisco ASA 5505 device with basic (default) license, currently all my reirections, VPN's, VLAN's(3 Vlan's) etc are configured on the same and are working fine.Now i need to upgrade my basic license to "Security Plus" for some additional features, if i upgrade it directley is there any complications in present rules, below is my doubhts
 
1. if i upgrade, did it change any of my present configurations ?
2. is there any name change or property changes for VLAN's or VPN's
3. did it affect the firewall functions
4. If anything goes wrong, can i restore it in to my old state using my previous dump.

View 1 Replies View Related

Cisco :: LMS 4.0 To 4.1 Upgrade License - Install 4.1 Directly?

Nov 21, 2011

We face following situation: Currently LMS 3.2 is installed. We order a 3.x to 4.0.1 upgrade license, in the meantime 4.1 is launched. So, we ordered the free of charge 4.0 to 4.1 minor upgrade license. Now we have a 3.x to 4.0 upgrade license and the 4.0 to 4.1 minor upgrade license and don't know how to proceed.
 
Is it now possible to install 4.1 from scratch directly and use the 4.0 to 4.1 upgrade license to register it? Of course we want to avoid to install 4.0 as an extra step...

View 3 Replies View Related

Cisco VPN :: ASA5510 - License To Upgrade From 2 To 250 Users

May 21, 2013

i have bought the below licenses for the ASA5510 to upgrade from 2 to 250 users and yet i can give access to 2 users only.
 
L-ASA-AC-M-5510=
L-ASA-AC-E-5510=
 
Kindly find attached the "show version"

View 6 Replies View Related

Cisco Wireless :: 5508 With 50 AP License Upgrade From 7.0.220 To 7.4

Mar 13, 2013

5508 W LAN controller with 50 AP License upgrade from 7.0.220 to 7.4 is it will effect to the license and configuration? Because the license came pre- installed. 

View 1 Replies View Related

Cisco Security :: 880 NPE / How To Change License

Mar 26, 2012

i have cisco 880 with NPE licence, but i need encryption on this device. I change IOS to c880data-universalk9-mz.151-3.T1.bin, but i still have NPE License and only Evalution without NPE. How  can i have permanent license?
 
show license all
 
License Store: Primary License Storage
 StoreIndex: 0   Feature: advsecurity_npe                   Version: 1.0
License Type: Permanent
License State: Active, Not in Use

[code]....

View 3 Replies View Related

Cisco VPN :: ASA 5510 - Security Plus License

Aug 21, 2012

We’ve ordered ASA 5510 with security plus license as below description: 

ASA5510-K8
ASA 5510 Appliance with SW,   5FE, DES
L-ASA5510-SEC-PL=
ASA 5510 Security Plus License   w/ HA, GE, more VLANs + conns
 
The license details on the appliance shows as the below,
Fail over                        : Enabled 
Encryption-DES                  : Enabled 
Encryption-3DES-AES             : Disabled
Security Contexts                : Default 
GTP/GPRS                        : Disabled
Any Connect Premium Peers      : Default 
Other VPN Peers                 : Default 
Advanced Endpoint Assessment    : Disabled
Any Connect for Mobile            : Disabled
Any Connect for Cisco VPN Phone  : Disabled
Shared License                  : Disabled
UC Phone Proxy Sessions          : Default 
Total UC Proxy Sessions          : Default 
Any Connect Essentials            : Disabled
Bot net Traffic Filter            : Disabled
Inter company Media Engine        : Disabled 
  
I’ve noticed that the 3DES is disabled, do I need to order another license to use 3DES or not ?Also, I need 2 ~ 5 branches to connect simultaneously and have VPN access on their laptops to the main branch via vpn software, which VPN software I should use and is our license enough or I should order another license.

View 3 Replies View Related

Cisco Firewall :: ASA 5512 - Cannot Connect To VPN After License Upgrade

May 1, 2013

I am having an issue where I can't connect to VPN after upgrading the license. The license upgraded is related to AnyConnect VPN. I noticed from the newly upgraded license, the Encryption-3DES-AES is disabled whereas previously it was enabled.
 
ASA 5512-K9
Version 8.6(1)2

View 2 Replies View Related

Cisco WAN :: ASR1001 Upgrade - License Module Command

Oct 4, 2011

I'm trying to upgrade an asr1001 (r1) from asr1001-universal.03.02.00.S.151-1.S.bin to asr1001-universalk9.03.02.00.S.151-1.S.bin. i've put in the boot system flash asr1001-universalk9.03.02.00.S.151-1.S.bin command and reloaded but the box keeps loading first image the configuration register is 0x2102. i've tried the license module command to enable adv enterprise but it made no difference so i removed it again. my license is now;
 
License Package Information for Module:'asr1001'
Module name   Image level      Priority  Configured  Valid license   
asr1001            adv enterprise      1          NO           adv enterprise   adv ip services  2  NO adv ip services ip base  3   NO  ip base

View 2 Replies View Related

Cisco Firewall :: 6500 - Upgrade Context License

May 3, 2011

I have a firewall module in a Switch Catalyst 6500. I wan to  upgrade its context capacity to a greater capacity. When I looked it in the Dynamic configuration, it send me following number parts:
 
FR-SVC-FWM-VC-T1=
FR-SVC-FWM-UPGR1=
 
The first one is the license to have 20 context and the next one is upgrade from 20 context to 50 context. My problem is that I haven't could find a service support contract associate them.I want to know if they have or not service contract, because I can´t find them.

View 1 Replies View Related

Cisco Firewall :: Do Need Security Plus License To Do HA With Two 5520

Mar 7, 2011

Do I need the security plus license to do HA with two 5520's?I was told by our purchasing department that the 5520 was supposed to be able to do HA out of the box, but when I look I see only the VPN + license.  Does that mean I can download the security plus license?  Or do I even need it on the 5520.

View 2 Replies View Related

Cisco Firewall :: Security Plus License For ASA5505

Jul 2, 2012

I have Cisco ASA5505 8.2(5) connected with Cisco 5520 8.2(1) via IPSEC tunnel, I was able to SSH from the inside 5520 to inside IP of the asa5505. but I after I upgrade the license to security plus at 5505 I lost the SSH and ASDM to inside IP of 5505 from the inside network of the 5520. however I still can use SSH and ASDM on outside IP of 5505.
 
I did a lot of testing to make it work but I couldn't I added SSH 0.0.0.0/0 inside and outside also I added acl on both interfaces. when I did a trace on the outside interface from the private network of 5520 to 5505 inside IP I got IPSEC spoofed by the way that trace only works with security plus because I try to test on all my other firewalls 8.2(5) it shows nothing and all my firewalls can accessed from the private network 5520 except the one with the security plus!

View 11 Replies View Related

Cisco Security :: C2911 - Enable SSL VPN License

Jul 3, 2012

i had installed the SSL_VPN to the router C2911, running on IOS 15.0 But i couldn't see the SSL_VPN enable while i do show license feature? i did reload the router several time and accept the end user agreement.
 
attach the
01. show license feature
02. show license detail

View 1 Replies View Related

Cisco VPN :: 2911 - VPN License / Security Pack

Sep 25, 2012

We are designing a solution for our customer, they plan to connect 5 site to their main office, on the main office, they use CISCO2911, branch use CISCO1921, so my question is:
 
1, If I want to use IPSec VPN connect branch and main office, apart from the router, I only need to buy the Security pack, like SL-19-SEC-K9/SL-29-SEC-K9, no need to buy SL-19-DATA-K9/SL-29-DATA-K9, am I right? 

2, If I want to use SSL VPN connect branch and main office, apart from the router and SL-19-SEC-K9/SL-29-SEC-K9, I only need to buy L-FL-SSLVPN10-K9 for CISCO2911 in main office, no need to buy L-FL-SSLVPN10-K9 for branch as each CISCO1921 has two default SSL license?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved