i have bought the below licenses for the ASA5510 to upgrade from 2 to 250 users and yet i can give access to 2 users only.
L-ASA-AC-M-5510=
L-ASA-AC-E-5510=
Kindly find attached the "show version"
I´m trying to upgrade a Customer's ASA 5505 base license from 10 to 50 users (ASA5505-SW-10-50=). But the reseller sent a ASA5505-SW-50-UL= license instead. I tried to register that license and the following messaged appeared.
Wrong Sku(s) 'ASA5505-SW-50-UL=' for 'ASA5505-K8' : Device contains following licenses 'ASA5505-SW-10,ASA5500-ENCR-K9'
Serial Number = JMX1235Z0TZ
same platform type as the failed serial number. An upgrade request is not allowed. open a Service Request using the TAC Service Request Tool at [URL].As an alternative you may also call our main Technical Assistance Center at 800-553-2447.Sincerely,Cisco Systems Licensing.
I tried to contact TAC for assistance but It's not possible because that kind of service is outside the parameters of the service contracts associated with my cisco.com profile.
I have 10 user license for Cisco ASA, i have to use this ASA for client connectivity. Can i do NAT of more than 10 users with this license? What i understand is NO.
But as per Below explaination looks like, i can if i am not doing default routing? Actually i just need to add a specific Route towards client DMZ interface on my ASA, no default route, so can i use more than 10 concurrent sessions with this license?
i have CSC-SSM-20 i want to renew the license to support 750 users for 3 years if i have base license only also if i have base and plus?
View 1 Replies View RelatedI have a customer that has an asa5505 who purchased the ASA5500-SSL-25 license.He is now going to replace/upgrade to a 5510.Can he just install the license on the new ASA, providing that he gets some trade-in on the 5505.Does he have to purchase it all over again.
View 1 Replies View RelatedCurrently we have a CISCO 3020 VPN Concentrator to terminate Lan-to-Lan tunnels and have our mobile workers connect via CISCO VPN client (300 users-employees and contractors-). Since this device is coming to an EOL this year we purchased a CISCO 5520 (below are the current licenses on it)
The licensing seems rather complicated, therefore this is my question:
- What VPN solution do you recommend for our users and contractors? it is my understanding the CISCO VPN client does not work with ASA 5500 series devices
- Is there a license needed to deploy VPN solutions for our remote users(employees/contractors)?
I have setup ASA5510 in failover mode. I am planning to use this setup for clientless SSL VPN and have following questions.
1. Do I have to license both firewalls for SSL VPNs? These licenses are very expensive and why would I have to purchase it for secondary when I am not using it?
2. SSL vertificate for the firewall it self. Do I have to acquire one or two to ensure users don't get annoying message about self signed certificate? Cisco doesn't seem to have this discussion in any documents. However I found following URL discussing from somebody's experience. What's official statement from Cisco on this matter? [URL]
we have a customer with a ASA 5510 with a CSC module in it. The device tells us the Base license has expired. The new license has been renewed - after - the grace period. The Trendmicro site tells us the Base license is valid until 21 october 2013 but the CSC refuses to acknowledge this. The module is able to fetch updates form the Internet so it does not look like a connection problem to me (it also has a plus license which is also valid till far into 2013 and that one works).Is it possible that the current license key is "dead" and the CSC expects a new license key because the grace period was expired?
View 1 Replies View RelatedIs it possivble to have 10 security licenses, license to a Cisco 5510 and have them transfeered to a Cisco5520?
View 1 Replies View RelatedGetting the following alarm from my ISE:Cause:Base License Enforcement Details: Base concurrent users exceed license allowable count.Currently only using 1656 out of 2000 base licenses so I'm not sure what the issue is. Running 1.1.2.145 patch 3.
View 1 Replies View RelatedWe have a high availability pair of ASA 5510's in Data Centre where we have configured remote access to allow users log in via SSL VPN, now we want to add further security to our environment we are adding endpoint assessment licenses...the question I have would I need two sets of the license ASA-ADV-END-SEC ?
I learned the hardway before with ASA SSL VPN licenses breaking other failover pair as it needed identical licenses on both units! Will I need 2 separate license sets to keep my firewalls in a HA pair?
Web clients are receiving login failed messages and VPN clients are getting disconnected by host messages. I am able to ping the server from the ASA5510. Users authenticate in AD. I am not sure if the problem is on the server or the ASA.
View 1 Replies View RelatedI want to set-up a HA for ASA5510. I wanted to design the network to achieve HA. I am attaching the present set-up of the network. At present, I have 2 ISPs connections terminating in ASA5510. The configuration is done for failover in ASA5510.I have another ASA5510 and want to use it for HA. I needed to know the design for the set-up. I want a stateless failover since the amount of traffic is less. I don't have any ISP routers in the present network. I suppose I need 2 routers for HA and couple of switches. One more question is that, as there are SSL VPN users, is there any way for the users to not get disconnected when one device fails.
View 5 Replies View RelatedI have ASA5540 with 1000 SSL-VPN License, then I would like upgrade from 1000 to 2000. Which part I have to add between
L-ASA-SSL-1000=
L-ASA-SSL-1K-2500=
ASA5500-SSL-1000=
We are currently preforming the upgrade from WCS v.7.0.230.0 no NCS 1.1. When we select the Lic file we get an error message "Unable to add any license without an NCS (L-NCS-1.0-K9) license." The file name is WCSUPG20121115142018448.lic.
View 2 Replies View RelatedMy client is having a 5505 which supports 2 SSL peers as per now and we want an upgrade . I had a look into GPL and I was confused with two of the following part numbers . Which one should I go for as both of these look same for me and there is a huge difference in price .
ASA5500-SSL-10
ASA 5500 SSL VPN 10 Premium User License
ASA-AC-E-5505
AnyConnect Essentials VPN License - ASA 5505 (25 Users)
Not abe to upgrade the IOS image PIx7.0 from earlier version 6.3 in to my old Pix-525 FO(Secondary unit) license box .
Is it possible to upgrade without Primary unit (Unrestricted License) ?
I have a two ASA HA and I'd like to upgrade the license to ASA5500-SSL-250. I need to know if i have to purchase one license (ASA5500-SSL-250) for the Active unit and one license (ASA5500-SSL-250) for the standby unit.
View 3 Replies View RelatedI want to confirm if the upgrade license (ASA5505-SW-10-UL=) is backward compactible with PIX 501 firewall device? though pix 501is end of life bit i want to verify if the upgrade license for asa5505 will work with it?
View 4 Replies View RelatedI have a Cisco ASA 5505 device with basic (default) license, currently all my reirections, VPN's, VLAN's(3 Vlan's) etc are configured on the same and are working fine.Now i need to upgrade my basic license to "Security Plus" for some additional features, if i upgrade it directley is there any complications in present rules, below is my doubhts
1. if i upgrade, did it change any of my present configurations ?
2. is there any name change or property changes for VLAN's or VPN's
3. did it affect the firewall functions
4. If anything goes wrong, can i restore it in to my old state using my previous dump.
I have a Cisco 1921 ISR Router with Security License running software version 15.0. I want to upgrade the router to 15.1. But I don't want to lose the security license that came with the router. When I look at the IOS downloads page on Cisco, all I see is universal images for all versions of 15.1.
My question is - where is the security license stored? In the IOS or programmed in somewhere else of the router? If I upgrade my router to one of the newer 15.1 universal images, will I lose my security license?
We face following situation: Currently LMS 3.2 is installed. We order a 3.x to 4.0.1 upgrade license, in the meantime 4.1 is launched. So, we ordered the free of charge 4.0 to 4.1 minor upgrade license. Now we have a 3.x to 4.0 upgrade license and the 4.0 to 4.1 minor upgrade license and don't know how to proceed.
Is it now possible to install 4.1 from scratch directly and use the 4.0 to 4.1 upgrade license to register it? Of course we want to avoid to install 4.0 as an extra step...
5508 W LAN controller with 50 AP License upgrade from 7.0.220 to 7.4 is it will effect to the license and configuration? Because the license came pre- installed.
View 1 Replies View RelatedWe want to upgrade one of our Cisco 5505 with Security Plus license. what is the difference between L-ASA5505-SEC-PL and ASA5505-SEC-PL upgrade licenses?
View 1 Replies View RelatedI am having an issue where I can't connect to VPN after upgrading the license. The license upgraded is related to AnyConnect VPN. I noticed from the newly upgraded license, the Encryption-3DES-AES is disabled whereas previously it was enabled.
ASA 5512-K9
Version 8.6(1)2
I would like to Upgrade license Cisco 1941-K9 from ipbase to security
View 5 Replies View RelatedI'm trying to upgrade an asr1001 (r1) from asr1001-universal.03.02.00.S.151-1.S.bin to asr1001-universalk9.03.02.00.S.151-1.S.bin. i've put in the boot system flash asr1001-universalk9.03.02.00.S.151-1.S.bin command and reloaded but the box keeps loading first image the configuration register is 0x2102. i've tried the license module command to enable adv enterprise but it made no difference so i removed it again. my license is now;
License Package Information for Module:'asr1001'
Module name Image level Priority Configured Valid license
asr1001 adv enterprise 1 NO adv enterprise adv ip services 2 NO adv ip services ip base 3 NO ip base
I have a firewall module in a Switch Catalyst 6500. I wan to upgrade its context capacity to a greater capacity. When I looked it in the Dynamic configuration, it send me following number parts:
FR-SVC-FWM-VC-T1=
FR-SVC-FWM-UPGR1=
The first one is the license to have 20 context and the next one is upgrade from 20 context to 50 context. My problem is that I haven't could find a service support contract associate them.I want to know if they have or not service contract, because I can´t find them.
We are planning to upgrade the ASA license in an A/S pair by adding the ASA5500-SC-20= license. The ASA is 5545 and runs 8.6. According to documentation, after 8.3 version, the ASAs can share a license features and do not require the same license on both boxes. I run a test in GNS3 with 8.4(2) images and I saw that by adding the 'activation-key' command only on the primary unit did the job as the 'show activation-key' output shows. In order to be 100% sure would like to verify the following:
Putting the activation-key only on the primary unit is enough and there is no need to do anything elseIn case the primary unit is standby, again we have to put the actication-key command on the primary unit (I am asking this because the 'activation-key' command is not listed under the commands that are not replicated to the other unitk, but doesn't make sense to be replicated since the activation-key is 'tied' with the S/N of the device).
Would like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies View RelatedI'm planning to upgrade Cisco ASA 8.2 to an anyconnect essentials and mobile license. Are there any concerns with some users continuing to utilize the cisco vpn IPSEC client while others migrate to the Anyconnect? I just want to make sure when I upgrade the license that there will not be an immediate requirment to have all users switch to Anyconnect immediately.
View 2 Replies View RelatedI have two 3750x in a stack running c3750e-universalk9-mz.122-55.SE3.bin with License Level: ipservices?I am planning to upgrade to c3750e-universalk9-mz.122-58.SE2.bin will this keep my ipservices licence or revert back to IPbase
View 3 Replies View RelatedI recently added a 3750X-24P-L into a stack of 3750V2 switches. I did so by getting the temporary upgrade license from LAN Base to IP Services; I added the switch no problem. I now have the permanent license and I was wondering if I could install the permanent license without having to remove the switch from the stack. I tried a license install but that failed. The switch is not currently the master but I figured I might promote it and then try the install.
View 4 Replies View Related