i have 2921 router with base license . i want to upgrade to it to security k9 feature or want to enable it. i have license file with product activation key. how should i do it. if any body have screen shot file
View 1 RepliesThe model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies View RelatedWould like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies View RelatedI have two 3750x in a stack running c3750e-universalk9-mz.122-55.SE3.bin with License Level: ipservices?I am planning to upgrade to c3750e-universalk9-mz.122-58.SE2.bin will this keep my ipservices licence or revert back to IPbase
View 3 Replies View RelatedI recently added a 3750X-24P-L into a stack of 3750V2 switches. I did so by getting the temporary upgrade license from LAN Base to IP Services; I added the switch no problem. I now have the permanent license and I was wondering if I could install the permanent license without having to remove the switch from the stack. I tried a license install but that failed. The switch is not currently the master but I figured I might promote it and then try the install.
View 4 Replies View RelatedI have a Cisco 1921 ISR Router with Security License running software version 15.0. I want to upgrade the router to 15.1. But I don't want to lose the security license that came with the router. When I look at the IOS downloads page on Cisco, all I see is universal images for all versions of 15.1.
My question is - where is the security license stored? In the IOS or programmed in somewhere else of the router? If I upgrade my router to one of the newer 15.1 universal images, will I lose my security license?
I have a cisco router 1941 and i have uploaded before evaluation license , now i have already bought cisco security license .I have already installed on cisco router , but the problem the router is still using the evaluation license not the new license .
RSP#sh flash:
-#- --length-- -----date/time------ path
1 55088360 Oct 10 2012 06:04:10 +00:00 c1900-universalk9-mz.SPA.151-4.M4.bin
2 2903 Feb 4 2013 12:23:32 +00:00 cpconfig-19xx.cfg
[Code].....
We want to upgrade one of our Cisco 5505 with Security Plus license. what is the difference between L-ASA5505-SEC-PL and ASA5505-SEC-PL upgrade licenses?
View 1 Replies View RelatedI would like to Upgrade license Cisco 1941-K9 from ipbase to security
View 5 Replies View RelatedWe are planning to upgrade the ASA license in an A/S pair by adding the ASA5500-SC-20= license. The ASA is 5545 and runs 8.6. According to documentation, after 8.3 version, the ASAs can share a license features and do not require the same license on both boxes. I run a test in GNS3 with 8.4(2) images and I saw that by adding the 'activation-key' command only on the primary unit did the job as the 'show activation-key' output shows. In order to be 100% sure would like to verify the following:
Putting the activation-key only on the primary unit is enough and there is no need to do anything elseIn case the primary unit is standby, again we have to put the actication-key command on the primary unit (I am asking this because the 'activation-key' command is not listed under the commands that are not replicated to the other unitk, but doesn't make sense to be replicated since the activation-key is 'tied' with the S/N of the device).
I have a Cisco 2921 router running c2900-universalk9-mz.SPA.150-1.M4.bin.Its licensed for ipbase, ipbasek9, Permanent and uc,uck9,Permanent (I'm using the router as a voice gateway),I'm looking to update the IOS to c2900-universalk9-mz.SPA.150-1.M5.bin as I'm told it has a fix for some DSP problems.So the question is, do I need to obtain a new license key to apply this update or am I covered by the existing license on the router.
View 3 Replies View RelatedI have a brand new 2901 and I'm trying to work out what licence features I have. The output of show licence shows I have ipbasek9 feature and datak9 as EvalRightToUse feature. Is BGP included in the base feature? What will happen when the datak9 evaluation period expires?
View 1 Replies View RelatedWhat's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI have recently purchased 2 x 1941 routers with 2 L-SL-19-SEC-K9= and 2 L-FL-SSLVPN10-K9= licenses. I've installed the licenses through Cisco Configuration Pro ver 2.5 and installation did not generate any errors. After saving config and reloading the device, on the License dashboard, the deploy status for the SSL VPN is "Not deployed" and I have no way of deploying it. The state also says "Active, Not in use". I have tried reinstalling the license via command line but get error "license duplicate - already installed" suggesting the installation was OK. The sec license deployed without any issues. Is there any way to manually deploy this SSL_VPN license?
View 4 Replies View RelatedI have installed Cisco Prime Infrastructure 1.2 separately from LMS4.2. LMS4.2 is in production. I just want to run PI1.2 in parallel with LMS4.2 before migrating to PI1.2. Currently I have LifeCycle permanent license. Why don't I have the assurance lfeature set license. it is running in evaluation mode.
View 6 Replies View RelatedI have installed Cisco Prime Infrastructure 1.2 separately from LMS4.2. LMS4.2 is in production. I just want to run PI1.2 in parallel with LMS4.2 before migrating to PI1.2. Currently I have LifeCycle permanent license. Why don't I have the assurance lfeature set license. it is running in evaluation mode.
View 1 Replies View RelatedLately we have been comsidering an upgrade in our organization involving a 1921 router. The main role it will play is a load balancer/failover between 2 connections from 2 different ISPs. what additions are required to be added to this piece of equipment to make the configuration work. Im researching the matter now and it seems an extra card whould be purchased in addition to the router. Also, i cant seem to find much information on the available licenses to go with the router. will i need a special license to utilize the balancer/failover feature? (ip base, data, SEC).
View 2 Replies View RelatedI have an ASR1001 installed and I want to implement the firewall feature set.The current license level is IPbase and I have the firewall feature installed. The firewall feature shows acive, Not in use. I have tried to activate it without success. My question is: do I need to get a license for advipservices or adventerprise to activate the firewall feature set?
View 5 Replies View RelatedI've problem with IP SLA probes between two different routers.2900 (c2900-universalk9_npe-mz.SPA.151-4.M4.bin) here is set "ip sla responder" only and 2800 (c2800nm-advipservicesk9-mz.124-24.T2.bin) here is set two type of tests "udp-jitter" and "icmp-jitter" - temporary, used to check for availability of 2900 router.As a result, I've what udp-jitter doesn't work at the same time icmp-jitter test is OK.Here are the settings of IP SLA tests
ip sla 281
icmp-jitter 172.25.28.1 source-ip 192.168.28.6 num-packets 100
tos 128
frequency 120
ip sla schedule 281 life forever start-time after 00:05:45
[code]...
I have bought DRAM MEM-2900-2Gb for 2921, and received the following error...
Validation failed for DIMM0
*****System halted*****
%SPD info: DIMM0: Invalid DIMM type (only UDIMMs are supported)
I am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
one of our switches (WS-C2960G-24TC-L). When I try to turn on the lanbase-routing feature using sdm prefer lanbase-routing, it gives me an error (Unknown command). I tried "sdm prefer ?", and lanbase-routing wasn't there (only qos, default and dual IPv4 & IPv6). The switch is running on image C2960-LANBASEK9-M version 12.2(50)SE5.We have another switch (WS-C2960S-24TS-L), running on image C2960S-UNIVERSALK9-M version 12.2(55)SE5, and I can enable lanbase-routing feature. If I upgrade the WS-C2960G-24TC-L to version 12.2(55)SE5, will it be able to do inter-vlan routing? Or is the switch itself totally limited to VLAN configuration only?
View 4 Replies View RelatedCisco C2960S IOS:12.2(55)SE5
Cisco C3560X IOS: 12.2(55)SE3
The 3560 switch is serving as an access and distribution layer switch. End devices are connected to it and it also implements IP routing via SVI and L3 ports.Auto qos voice cisco-phone has been implemented on applicable access layer ports. SRND4 is being used.
2960:
mls qos map policed-dscp 0 10 18 24 46 to 8
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue output cos-map queue 1 threshold 3 4 5
mls qos srr-queue output cos-map queue 2 threshold 1 2
mls qos srr-queue output cos-map queue 2 threshold 2 3
mls qos srr-queue output cos-map queue 2 threshold 3 6 7
[code].....
Question 1:Why is the auto qos generated policed-dscp map different on these two switches?The Cisco Smart Business Architecture LAN configuration files guide [URL] does not specifically use the 3560 in their examples, they use the 3750 but it's my assumption that the same techniques, configs apply with regard to my specific feature questions. When using a 3750 in the Access layer, the guide shows (page 15) the same auto qos generated policed-dscp map configuration that is on my 2960. The SBA LAN config guide shows that when using a 3750 as a Distribution layer switch (page 26), the policed-dscp map configuration is the same that I see on my 3560.In the configuration guide for the 3750 distro switch, there is no auto qos applied as there are no access ports, so the mls qos commands are manually input. Since my 3560 does have access ports, auto qos generated the mls qos commands, and the results are the same be it following the guide and manually entering (per distro switch guidelines) or using auto qos. This leads to question 2...
Question 2:Why is the mls qos map policed-dscp configuration different depending on use as an access vs. distribution switch?
Question 3: On the 3560, access ports that have "auto qos voice cisco-phone" applied are put into queue-set 2 (output). Queue-set 2 (output) uses default values (not configured). Is this correct and desirable? If so, why? The 2960 has all ports in queue-set 1, regardless of being an access device port or a trunk port connected to the 3560 (as per the SBA LAN config guide EgressQOS macro commands). The 3560 trunk ports are all also configured to use queue-set 1 (output), again as per the SBA LAN config guide EgressQOS marco commands.
I have a few old 2600 routers (2621, different IOS's) which I'm now replacing for new one's from the 2900 series (2901, Version 15.1(4)M4).In my configuration I have two IP addresses in my LAN interface and I have HSRP configured within the secondary IP subnet range. It would be something like this:
interface GigabitEthernet0/1
ip address 172.x.x.x x.x.x.x secondary
ip address 10.z.z.z z.z.z.z
[Code].....
Now, in the new 2900 routers, my interface configuration hasn't changed however I can see that the hello packets are now sent with the source within the respective HSRP IP subnet so I had to edit my acl for that:
permit udp 172.x.x.x x.x.x.x host 224.0.0.2 eq 1985
Is there a way I can force the HSRP to work as it previously did in the old IOS's?
I have a 2900 router at branch office. This router has a 4 port switch card and two gigabyte ports. The gigabyte port is use for wan connection and the 4 port switch card is use for lan connection. I have two separate networks on my lan side. (network 1 and network 2)
I have assigned port 0,1 of the switch card to vlan1 for network 1 Ports 2,3 of the switch card is assigned vlan 20 for network 2
My problem is I would like to applied a bandwidth restriction for all data coming out from vlan20 capping same to 384 kb.
Note I do not want use QOS because this will only kickin when saturation occurs,
how to change the Baud Rate on Cisco 2900 SW utilizing ROMON ?
View 8 Replies View RelatedI know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
we ordered a data e-delivery PAK L-SL-29-DATA-K9= (FOR A 2900 SERIES ROUTER) but after we received the PAK we discovered that the client actually has a 1900 router. Any easiest way of rectifying this mistake so that we can use the PAK on a 1900 series router?
View 1 Replies View RelatedTrying to apply this config to a 2900 router and getting this error message. [code] This works ok in in a 2800 router using 12.4(25d) spservices IOS
Not working on 2911 using 15.2(3)T2 ipbase image.
How to configure a module NM-16ESW because with the command "show diag" and "show int" can not query it.
Note: the default IOS is installed, you will need to upgrade to a specific '.
I have a query regarding attached Network Design
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
I have asked to test an VPN phone for home Users. I have a BT adsl broadband at home which is going into a cisco 2900 switch. Port One is connect to the computer port 3 is connected to the Avaya VPN phone this work's. The quality is not very good, so the question is could I have qos on Port 3 which is connected to the phone?
View 4 Replies View RelatedI have came across this topic, and I am wondering if this images can be uploaded to any 2900 series switches or not, and if this will work as access port for more than vlans. URL...
View 2 Replies View Related