Cisco Switching/Routing :: 3750X Did Not Have NAT Feature
May 22, 2013
I have a query regarding attached Network Design
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
View 4 Replies
ADVERTISEMENT
Oct 26, 2011
I have been looking to find out the list of features that the IP Base IOS has for the 3750X series switch. What would be ideal is a comparable list but essentially I need to know which of the LAN Base/IP Base/IP Services has SSH functionality.
View 1 Replies
View Related
Sep 9, 2012
Full feature set for IP Base with the 3750x.I just wanted to verify that I could create a routed port, turn ip routing on, and create static routes as well as a default route. From what I can find, there shouldn't be a problem with this on the IP Base Feature Set, I just wanted to verify. Or any link for the Features of IP Base on the 3750x.
View 3 Replies
View Related
Aug 23, 2011
I have a stack of five 3750X's connected in a single stack with the stackwise cables. Within this one stack, I created two power stacks, one power stack has 3 switches and the other has two switches. In each of the separate power stacks, one power stack port on a switch shows "shut", so the power stacks are not operating in a full ring. Is there a way to do a "no shut" on those stacks ports that are shut? IOS is 12.2(55)SE1
Here is the configuration -
stack-power stack XXX
stack-power stack YYY
!
stack-power switch 1
stack XXX
stack-power switch 2
[code]...
View 2 Replies
View Related
Oct 18, 2011
I am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
View 5 Replies
View Related
Feb 3, 2013
one of our switches (WS-C2960G-24TC-L). When I try to turn on the lanbase-routing feature using sdm prefer lanbase-routing, it gives me an error (Unknown command). I tried "sdm prefer ?", and lanbase-routing wasn't there (only qos, default and dual IPv4 & IPv6). The switch is running on image C2960-LANBASEK9-M version 12.2(50)SE5.We have another switch (WS-C2960S-24TS-L), running on image C2960S-UNIVERSALK9-M version 12.2(55)SE5, and I can enable lanbase-routing feature. If I upgrade the WS-C2960G-24TC-L to version 12.2(55)SE5, will it be able to do inter-vlan routing? Or is the switch itself totally limited to VLAN configuration only?
View 4 Replies
View Related
Jul 22, 2012
We are going to be rolling the 4500 switches out and I wanted to know more about how to use the wireshark featue. Any documentation on how to use this?
View 2 Replies
View Related
Oct 12, 2006
Had problems with voice quality on VoIP with 4500 series switches and the qos dbl feature (which gets enabled by the auto qos feature)?? I have had a couple of customer complaining about voice quality and our voice team spent a lot of time investigating; I had ruled out the network infrastructure because it was all QOS enabled. The voip people came up against a blank so I looked at the network once more and disbaled dbl with hope more than anything else. Mysteriously the voice quality issues the customer was having have now disappeared. Not sure whether a coincidence (though I have done this on two customers now) or something to with with dbl. There is nothing on this on cco.
View 3 Replies
View Related
Dec 13, 2011
I've a 3750-48ps-s running ios version: c3750-advipservicesk9-mz.122-46.SE.bin
I've tried to configure ipv6 on an interface but it does not give me the option.
How do I know if my ios is IPv6 capable?
View 1 Replies
View Related
Dec 19, 2012
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies
View Related
Jan 7, 2013
I have a 2911 router with 15.1(4) Ios Version. I need to enable the evaluation sna feature but when I try to enter the command "license feature snasw" but I get an error, the command "License feature" does not exist.
View 3 Replies
View Related
Dec 18, 2012
i have 2921 router with base license . i want to upgrade to it to security k9 feature or want to enable it. i have license file with product activation key. how should i do it. if any body have screen shot file
View 1 Replies
View Related
May 6, 2013
can you stack a 3750 switch over fiber.....the answer is no, but the virtual switching supervisor 720-10G for the 6500 can create one virtual switch using two 6500s...
how can we get cisco to come up with a way for access switches to be stacked over fiber similar to above supervisor? i know of few of my site that would benefit from this...maybe they can come up with a vss appliance, similar to a media converter, to convert stackwise over fiber...then of course, you would need the same appliance on the other end....
View 3 Replies
View Related
Apr 17, 2012
Do Cisco Catalyst (IOS) and specially Cisco SG300/500 support a similar feature to HP's Loop Protection or DLINK's Loopback Detection? This is an interesting feature to avoid loops caused by unmanaged switches.
View 6 Replies
View Related
Jan 27, 2013
We have purchased two new Nexus 3548 switches. According to documenation the Nexus 3K does support vPC. When trying to enable the feature I get this:
nexus(config)# feature vpc
Error: vPC feature is not supported
nexus(config)#
We are running software version version 5.0(3)A1(1) and it looks like the latest version is 5.0(3)A1(2) so that's not much of a difference.Am I missing something here?
View 4 Replies
View Related
Aug 14, 2012
I have a vlan that is used for ip cameras. This vlan is routed with other vlans on our Cat 4506-E. how can i implement multicast feature to improve performance?
View 1 Replies
View Related
Feb 18, 2013
I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies
View Related
Jan 7, 2012
The model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Mar 6, 2013
i cant find any difference in these two devices when i am trying to compare throughput.I need upgrade our new POP and there will be around 4900 MAC adresses in VLAN 150 and 130 MAC adresses in vlan 200.Uplink is 1 gig routed internet connection and there is 14 downlinks to separate villages.i found a few differences for eg stack interface on 3750x but i dont need it.
View 2 Replies
View Related
Dec 27, 2012
I have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
View 4 Replies
View Related
Dec 9, 2012
I have an 1811 with several subnets connected to it.I recently installed a 3750x plant and want to bring my interior routing back to it.
All the routing is handled by the 1811 via secondary interfaces on vlan1?
I have 192 ports, and subnets show up on almost all of them. None of the ports are assigned to any specific vlans. Most ports have several subnets on them.
What is the best approach to getting the 3750x to handle the routing?
View 18 Replies
View Related
Aug 22, 2012
As per my understanding, Cisco Nexus 2232 can only connect to HP c7000 Chassis if we are using a Pass Through Switch in the HP c7000. Cisco Nexus 2232 can only connect to End Hosts and not to a switch. Is there a New Feature added in Nexus 2232, which enables it to connect to a Switch like HP Flex Fabric ?
View 1 Replies
View Related
May 22, 2013
my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies
View Related
Jan 24, 2013
I am setting up a vm environment for a customer in my lab off site. I have two stacked 3750-x switches, a san, and threes UCS c220 M3S servers for hosts. I am trying to separate the lan traffic, san iscsi traffic, and san management traffic using vlans. The problem is i'm unable to communicate cross vlan with my current config, which I have attached to this post. The only noteworthy things in my conifg is that the ip route 0.0.0.0 0.0.0.0 192.168.83.6 is referring to a switch stack they have on site, that I will connect this stack to using the first two trunk ports on each switch, that I do not have here in the lab. I don't want to cause any confusion in why I have things set a certain way.
View 1 Replies
View Related
Mar 28, 2012
Why does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
View 1 Replies
View Related
Mar 4, 2013
I want to confirm this is a licensing issue. On a 3750X with ipbase, I cannot create a vrf. So I would need the universal image, and that is a seperate license, correct?Is there a link that describes the difference bewteen ipbase and univeral images?
View 6 Replies
View Related
Jan 5, 2013
scenario A
A site .
PBX --->
Data ---> other brand router ----> 3750X ---> wan
[Code]....
How to know whether QoS work on the 3750X or not ? Is it correct about the config in scenario A ?
View 2 Replies
View Related
Feb 3, 2013
I have a one question. I am using Cat3750x-48 switch. Suddenly it has occurred following high CPU log message in Cat3750x-48 switch.
%SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU Utilization(Total/Intr): 62%/0%, Top 3 processes(Pid/Util): 162/40%, 156/10%, 74/1%
What is meaning of PID 162 ?
View 1 Replies
View Related
Jan 1, 2013
There seems to be a lot of conflicting information on what can and can't stack together in the 3750X range.
I know that LAN Base can only stack with other LAN Base switches.
Can IP Base stack with IP services in 3750X? I have also heard that the 15.x.x IOS restricts mixed feature set stacks?
I know that Cisco recommends that all switches in a stack have the same IOS and feature set but having all IP Services in a stack can get too expensive.
View 6 Replies
View Related
May 7, 2013
I'm trying to review a QoS setup, and I'd like to make sure I fully understand the current setup before I change anything. I'm seeing output drops on two different queue-thresholds, but not sure how packets are making it to one of the queues.
Switch Version
CORE#show ver
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.0(2)SE, RELEASE SOFTWARE (fc1)
System image file is "flash:/c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin"
cisco WS-C3750X-24 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Switch Ports Model SW Version(code)
I can find queue4-threshold3 in the mappings, but how are packets getting mapped to queue2-threshold1? The priority queue is disabled for this interface, so I'm not sure how this queue is dropping packets, according to the maps nothing is mapped to 02-01.
View 3 Replies
View Related
Mar 21, 2013
I am building a switch stack using 4 48 port 3750X switches that will also have the power stacked. If I install a single 715W power supply in each switch will the stack support 802.3af accross all 48 ports on each switch? My calculations are 48 ports x 15.4W which gives me almost 740W needed which is over hte 715W power supply. I was reading somewhere were it mentioned that in a powerstack additional power can be drawn from the stack. I know this will not work if you are trying to support power on all switches accross all ports but would it if say 2 of the 4 switches are needing to provide PoE accross all 48 ports? If I say we can only use 24 ports per switch for PoE that drops the power need down to 370W which I believe should work. Just trying to get a better understanding of PoE consumption. Would the best solution be to just add a second power supply to each switch?
View 8 Replies
View Related
Nov 24, 2012
I have a switch which is rebooting it self, we bought it a year back,its a new switch, i did not find any error on sh ver after rebooting. I am using OP manager, i did not receive any alerts. I have done all diagnostic test, all are passed, i did not find any problem..
View 2 Replies
View Related
