I have a 2911 router with 15.1(4) Ios Version. I need to enable the evaluation sna feature but when I try to enter the command "license feature snasw" but I get an error, the command "License feature" does not exist.
View 3 RepliesI have an ASR1001 installed and I want to implement the firewall feature set.The current license level is IPbase and I have the firewall feature installed. The firewall feature shows acive, Not in use. I have tried to activate it without success. My question is: do I need to get a license for advipservices or adventerprise to activate the firewall feature set?
View 5 Replies View RelatedI am not able to activate the wireless feature in siemens gigaset se568.
View 1 Replies View RelatedI have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies View RelatedWe have purchased a number of 2911 routers.We got Base & security license as we wanted to enable encryption. However we probably wont use the security.We are replacing 2811 routers.Unfortunately the 2811 routers have FXS ports with 2 - 4 POTS handsets - I completely forgot about these ports when I was ordering.Now I have VIC3-FXS cards which are ok in the 2911 but unfortunately I cant get them to work.I am missing PVDMs (well adapters anyway), and even if I got them the router wont take any commands relating to voice due to the license.Is is possible to 'rehost' the security and turn it into a UC ?I am new to these 2911 and Licensing.
View 1 Replies View RelatedI have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies View RelatedI have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
I am planning on having a contractor in to configure some new routers and would like for him to login using the local account on the routers while company personal continues to use radius is this possible.
View 6 Replies View RelatedMy engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
I am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies View Relatedwhether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies View RelatedWe have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
I am having 2911 router running with C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)IOS and i have configured the following commands for eigrp
-router eigrp 100
-network 10.20.0.0
-no auto-summary
It takes all 3 commands but when i check through show run command i am not seeing no auto-summary command.
how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
I am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies View Relatedi have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
one of our switches (WS-C2960G-24TC-L). When I try to turn on the lanbase-routing feature using sdm prefer lanbase-routing, it gives me an error (Unknown command). I tried "sdm prefer ?", and lanbase-routing wasn't there (only qos, default and dual IPv4 & IPv6). The switch is running on image C2960-LANBASEK9-M version 12.2(50)SE5.We have another switch (WS-C2960S-24TS-L), running on image C2960S-UNIVERSALK9-M version 12.2(55)SE5, and I can enable lanbase-routing feature. If I upgrade the WS-C2960G-24TC-L to version 12.2(55)SE5, will it be able to do inter-vlan routing? Or is the switch itself totally limited to VLAN configuration only?
View 4 Replies View RelatedI have a query regarding attached Network Design
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
I have been looking to find out the list of features that the IP Base IOS has for the 3750X series switch. What would be ideal is a comparable list but essentially I need to know which of the LAN Base/IP Base/IP Services has SSH functionality.
View 1 Replies View RelatedFull feature set for IP Base with the 3750x.I just wanted to verify that I could create a routed port, turn ip routing on, and create static routes as well as a default route. From what I can find, there shouldn't be a problem with this on the IP Base Feature Set, I just wanted to verify. Or any link for the Features of IP Base on the 3750x.
View 3 Replies View RelatedWe are going to be rolling the 4500 switches out and I wanted to know more about how to use the wireshark featue. Any documentation on how to use this?
View 2 Replies View RelatedHad problems with voice quality on VoIP with 4500 series switches and the qos dbl feature (which gets enabled by the auto qos feature)?? I have had a couple of customer complaining about voice quality and our voice team spent a lot of time investigating; I had ruled out the network infrastructure because it was all QOS enabled. The voip people came up against a blank so I looked at the network once more and disbaled dbl with hope more than anything else. Mysteriously the voice quality issues the customer was having have now disappeared. Not sure whether a coincidence (though I have done this on two customers now) or something to with with dbl. There is nothing on this on cco.
View 3 Replies View RelatedI've a 3750-48ps-s running ios version: c3750-advipservicesk9-mz.122-46.SE.bin
I've tried to configure ipv6 on an interface but it does not give me the option.
How do I know if my ios is IPv6 capable?
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies View Relatedi have 2921 router with base license . i want to upgrade to it to security k9 feature or want to enable it. i have license file with product activation key. how should i do it. if any body have screen shot file
View 1 Replies View Relatedcan you stack a 3750 switch over fiber.....the answer is no, but the virtual switching supervisor 720-10G for the 6500 can create one virtual switch using two 6500s...
how can we get cisco to come up with a way for access switches to be stacked over fiber similar to above supervisor? i know of few of my site that would benefit from this...maybe they can come up with a vss appliance, similar to a media converter, to convert stackwise over fiber...then of course, you would need the same appliance on the other end....
Do Cisco Catalyst (IOS) and specially Cisco SG300/500 support a similar feature to HP's Loop Protection or DLINK's Loopback Detection? This is an interesting feature to avoid loops caused by unmanaged switches.
View 6 Replies View RelatedWe have purchased two new Nexus 3548 switches. According to documenation the Nexus 3K does support vPC. When trying to enable the feature I get this:
nexus(config)# feature vpc
Error: vPC feature is not supported
nexus(config)#
We are running software version version 5.0(3)A1(1) and it looks like the latest version is 5.0(3)A1(2) so that's not much of a difference.Am I missing something here?
I have a vlan that is used for ip cameras. This vlan is routed with other vlans on our Cat 4506-E. how can i implement multicast feature to improve performance?
View 1 Replies View RelatedI am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies View RelatedThe model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies View RelatedAs per my understanding, Cisco Nexus 2232 can only connect to HP c7000 Chassis if we are using a Pass Through Switch in the HP c7000. Cisco Nexus 2232 can only connect to End Hosts and not to a switch. Is there a New Feature added in Nexus 2232, which enables it to connect to a Switch like HP Flex Fabric ?
View 1 Replies View Related