My engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
On my 2650 Router it just has only Telnet password.It has no enable mode password set.After reboot it is goes to prompt mode BB.I am unable to go to enable mode .how can i go back to enable mode on this router?
View 13 Replies View RelatedMy current production network is setup using VTP in Client mode, and I am looking to enable VTP Transparent so I can enable the extended VLANs. My main question would be, would enabling VTP Transparent on my 6509 affect all of the access switches it is connected to? And if so, would changing all of the access switches to VTP Transparent allow them to regain connectivity quickly with little downtime? Or is there another way that I should be handling this situation to enable the extended VLANs?
View 2 Replies View RelatedI have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies View RelatedWe have purchased a number of 2911 routers.We got Base & security license as we wanted to enable encryption. However we probably wont use the security.We are replacing 2811 routers.Unfortunately the 2811 routers have FXS ports with 2 - 4 POTS handsets - I completely forgot about these ports when I was ordering.Now I have VIC3-FXS cards which are ok in the 2911 but unfortunately I cant get them to work.I am missing PVDMs (well adapters anyway), and even if I got them the router wont take any commands relating to voice due to the license.Is is possible to 'rehost' the security and turn it into a UC ?I am new to these 2911 and Licensing.
View 1 Replies View RelatedI have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies View RelatedI have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
I have a 2911 router with 15.1(4) Ios Version. I need to enable the evaluation sna feature but when I try to enter the command "license feature snasw" but I get an error, the command "License feature" does not exist.
View 3 Replies View RelatedI am planning on having a contractor in to configure some new routers and would like for him to login using the local account on the routers while company personal continues to use radius is this possible.
View 6 Replies View RelatedI am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies View Relatedwhether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies View RelatedWe have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
I am having 2911 router running with C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)IOS and i have configured the following commands for eigrp
-router eigrp 100
-network 10.20.0.0
-no auto-summary
It takes all 3 commands but when i check through show run command i am not seeing no auto-summary command.
how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies View Relatedi have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
We have CISCO ASR 1002 router on our DC, I want to enable TACACS on this router.what is the usage of key, we need a separate key for every device? or. [code]
View 9 Replies View RelatedI have a simple setup where I have a 2911 router with three interfaces, Inside, Outside and a second "Inside" interface which is labelled as a DMZ. The Zone Firewall applied to the "DMZ" is actually Inside (until I can work through problems). I need to be able to access a device on the DMZ via its external IP so I have designed NAT to use IP Nat Enable commands. This is now working for me fine. However, since utilising IP Nat Enable, my zone firewall now denies return TCP / UDP traffic and consequently I no longer have any internet access. Looking at the syslog messages, the reason for this is that the router is denying these return flows not because they are matching the outside-to-inside policy, but rather they are matching the outside-to-SELF policy. The router seems the detect that the internet traffic is being returned to SELF, when in reality the NAT rule should pick this up and forward it to inside. I can understand why this is happening, because I am NATting all private / inside traffic behind the external IP of the router, which is assigned to the Gi0/0 interface. [code]
View 1 Replies View RelatedI received the following info from Cisco's TAC and wanted to inquire further before I start reconfiguring the switch:
In a redundant Sup-6E setup, the following configuration is supported :
- 1 TenGig uplink on Active Sup and 1 TenGig uplink on Standby Sup
- 1 TenGig uplink on Active Sup and 2 Gig uplinks on Standby Sup
- 2 Gig uplinks on Active Sup and 1 TenGig uplink on Standby Sup
- 2 Gig uplink on Active Sup and 2 Gig uplinks on Standby Sup
If you invoke shared backplane mode, the following configuration can also be supported:
- 2 TenGig uplinks(blocking) on Active Sup and 2 TenGig uplinks on Standby Sup
- 2 TenGig uplink(blocking) on Active Sup and 4 Gig uplinks on Standby Sup
- 4 Gig uplinks on Active Sup and 2 TenGig uplinks(blocking) on Standby Sup
- 4 Gig uplink on Active Sup and 4 Gig uplinks on Standby Sup
Here's the command and information about the "shared-backplane" mode :- [URL]
Currently, we have 2 SUP 6-Es(Module 5 - Active and Module 6 - Stand-by) setup in a redundent mode. I am planning on changing the redundent mode to the shared backplane mode so I can use 2 TenGig converters to uplink 2 access-switches. We purchased 2 TenGig converters and here is how I am planning on using them:
1- One will be used to uplink to two 3750 switches(stacked)
2- One will be used to uplink to a 2960 using a Gig SFP
My questions are:
1- Do I have to install the 2 TenGig converters(4-Gig Uplinks) in the same Module? Or can I use one one in module 5 and the second one in module 6?
2- Will changing the redundant mode to the shared backplane mode require rebooting the switch or disrupt the funtionality of the other linecards?
I was trying to enable AutoQoS on my router 3925 GE interfaces, but failed to do so !! But I was able to do so on FE interfaces !! I have Security/K9 and Data/K9 license on this router. Or do I still miss out anything ?? I am on IOS 150-1(M4).
I was able to enable AutoQoS on all my Cisco 2811 and 1841 routers !
i cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedI am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View Relatedconfig to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
View 2 Replies View Relatedi downloaded and transfered the new ios to the 2911, but no install routine started.
View 3 Replies View Relatedafter installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
View 1 Replies View RelatedI'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies View RelatedI have purchased these two switches from ebay as a test lab, I plan to connect them up via a gigastack modulecable and enable ip routing on the c3550 and vlans to talk to each other.
I'm very much a procurve person and really need to get into the cisco switching.I will want to trunklacp between the switches - whats the process is setting that up on cisco switches?
I am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
I have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
View 21 Replies View RelatedI've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
we are in the planning phase for a network upgrade. We have two C2960 Switches connected via one (L2) Etherchannel (4x1 Gbit/s) which works very well. In the next phase we would like to upgrade our router to an 2911 series which has 3 gb interfaces. and indeed we would like to create an etherchannel as well. our plan is to use 2 of the 2911 to connect to the first 2960 switch and the one left to the other 2960. i think we will achieve some redundancy with this config.
View 6 Replies View Relatedconnected DSL directly to 2900 series router , but as DSL public IP is not static (dynamic) its difficult to access Router when out of home, any other means to access router without static IP
View 2 Replies View Related