I am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
Need to confirm about 2911 isr, what interface numbers are given to a 9esw when placed in the far left hwic slots (hwic slot 2+3).
I need to build some configs but its going to be a few more weeks before the kit arrives.
I need to configure a Cisco 2911. I need to give an interface in this module (VWIC3 - 4MFT-T1/E1) an IP address. My question is, how to assign an IP to an interface in this module.
My purpose is to get connectivity via T1 line to another router.
I have been having following situation on my WAN facing interface on Cisco2911 where the same number of broadcast, multicast and unknown protocol drops is happening. Not sure but some applications are struggling to run over on the WAN.
[code]....
I have both a Easy VPN server and a site-to-site VPN on the same outside interface of a 2911 router.
Currently, a Easy VPN client has no route int the router then out the site-to-site VPN to the remote site.
How can I create this route?
[code]...
According to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View RelatedI have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedOur organization currently has a Cisco 4507 acting as our core switch and 2 ASA525 firewalls.
Our existing ISP runs into our 4507. Here is the port config.
interface GigabitEthernet7/1
description ISP-DSL
switchport access vlan 10
[Code].....
We have recently purchased a 5Mbit line with a second ISP and will have the line activated tomorrow. In addition, we recently obtained our AS number through ARIN. How would I configure the second ISP to be used for load balancing/failover?
i downloaded and transfered the new ios to the 2911, but no install routine started.
View 3 Replies View Relatedafter installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
View 1 Replies View RelatedHow can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies View RelatedWe have the need to create a large number of VLANs on one of our networks. We're talking about 60! These will all terminate on a pair of 6509-E switches (building core). We use MSTP as a standard on our network so I'm going to stick with that so that we can dramatically reduce the number of STP instances needed. However, regarding the SVIs (default gateways) is there any reason why creating 60 of these guys would be considerd a big no-no? Or would you expect the 6509s to deal with them like a boss?
View 4 Replies View RelatedOn a Cisco 3560 with IP services ver. 12.2(35)SE5 I have tried to config BGP with a 6-digit AS number, and it is not possible. What software is needed for 6 digit AS number for PI IP addresses, and do I need to buy a new switch also.
View 5 Replies View RelatedWhether Cisco has part number for the large fan in 2811. I know p/n for small fan is already there, but I can't find any for large one( I think it s fan 3).
View 10 Replies View RelatedI have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 Replies View RelatedIf multilayer switch has routing capabilities then why we can go for dedicated router?
Why we cannot use a number for VLAN ID other than 1 to 4094 ?
We have IP device on the farm switch(cat6500, which is an access layer siwtch), with the gateway on the core switches (Nexus7000), on the core when I do show ip arp, I found the mac.But when I do sh mac add add of that mac there is no port attached to that mac.
Since that particular vlan only resides on the cat 6500 and two cores, so I logged in to the 6500, and when I show mac- in that vlan, I didn’t find that mac addresss. Instead, I found another mac address with last 8bit are the same of that mac.
Is it some kind VIP of the mac? How so, if no port, how can the switch forward the frame? [code]
I have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
View 21 Replies View RelatedI have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies View RelatedI've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
we are in the planning phase for a network upgrade. We have two C2960 Switches connected via one (L2) Etherchannel (4x1 Gbit/s) which works very well. In the next phase we would like to upgrade our router to an 2911 series which has 3 gb interfaces. and indeed we would like to create an etherchannel as well. our plan is to use 2 of the 2911 to connect to the first 2960 switch and the one left to the other 2960. i think we will achieve some redundancy with this config.
View 6 Replies View Relatedconnected DSL directly to 2900 series router , but as DSL public IP is not static (dynamic) its difficult to access Router when out of home, any other means to access router without static IP
View 2 Replies View RelatedI have 2 2911 routers that will be connected via fiber with an ethernet Gig handoff to each router. Each router will then be connected to local networks on a second ethernet interface on the router. I have always connected routers via serial connections so this is new to me. Outside of the usual ethernet interface addressing configuration, is there anything else that would need to be configured on the 2 routers?
View 1 Replies View RelatedIs there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies View RelatedWe currently have a stack of 5 x 3750 switches and i want to remove switch number 3 (it has the least number of things plugged in). What will happen to switch 4 and 5 will they be renumbered 3 and 4, and will the config automatically update this if it does?
View 2 Replies View RelatedIs there a maximum number of licenses for connections to a 877?The reason I ask is that our routers are managed by a datacentre and when I asked for the login details I was told that I couldnt have them due to licensing reasons with no other explanation.
View 1 Replies View RelatedI have a 6509-E chassis that was prevoius in a VSS configuration. Due to some VSL failures I had to cobvert it to a standalone chassis but would like to bring it back to a virtual system.
Whenever I try to convert it by using the command "switch convert mode virtual" I get the msg %Please configure local switch number first". After doing so by entering the CLI cmd "switch set switch_num 1 local" I still get the same message.
I have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
we have inserted into a network with VTP a Cisco Switch 2960-S, not knowing that had installed IOS LAN lite.Now I discovered that it can handle up to 64 vlan. In the network there are currently configured 62 VLAN: what happens when we exceeded the max number (64) of VLAN for that switch?
View 6 Replies View RelatedI found increasing number of overrun in the tengigabit interface. The hardware is 6509 with sup720-3B and the overrun output is shown in WS-X6716-10GE module. The connected device to WS-X6716-10GE is EMC Islion S200. I think the capability of WS-X6716-10GE can handle EMC NAS device and the load is not so busy. So I have no idea of handling this and the reason why this overrun packet is shown.
[Code]...
what is the maximum number of etherchannels i can build on a Cisco 2960S stack. We hoping to connected 15 servers using 2 port channels between two stacked 2960 for redunancey. So what is the max number of channels can i build using the 2960S? Is the max 6 or is it more?
View 4 Replies View RelatedAlthough I am quite used to using the WLC 4402 and the attached APs, I have no knowledge about licensing and I'm wondering if it has a limited number of AP's that can be controlled by the WLC? I'm not planning on adding 1000's but at the moment we have 21 and will probably be adding an additional 30 in the near future.
View 1 Replies View Related