I have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 RepliesHow can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies View RelatedIs there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies View RelatedWhere on the case is the serial number located? I have a dead one that needs RMA.
View 1 Replies View RelatedI am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
i have LMS 3.2 installed in my campus. i need the serial number of the LMS suite to open a service request with cisco. but unable to find the same. How to find the same.
View 1 Replies View RelatedHow to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies View RelatedI'm based in the UK and am using a DIR-655 router but I have no record of its serial number (there is no sticker on the item, and the original box is now missing) - is there any way I can ascertain which version of the router I have? As I understand matters, I need to know this so that I can apply the correct firmware upgrade, which is what I wish to do.
View 1 Replies View RelatedWhat is the equivalent oid as chassisid - .1.3.6.1.4.1.9.3.6.3.0, which gets the serial number for most cisco switches/routers is for the ASA 55XX series firewalls.
View 2 Replies View RelatedI need to get the serial number of SFP in WLC 5508 ver 7.0 but can't find the command, is this possible and if yes how can I get the S/N of SFF in WLC?
View 4 Replies View RelatedWe are running WCS 4.2 on linux. I need to find the serial number of the software so I can raise a TAC case. how to find the serial number? I cant see it via the GUI.
View 10 Replies View RelatedI have a problem with an AP1310 which may need me to open a case for RMA. is there any way I can view the serial number using the GUI since the AP is already installed on a high mast but I didn't enable telnet on that?
View 1 Replies View RelatedHow can I find the serial number at Cisco PIX-515E ?
View 2 Replies View Relatedi need the address of my pro 900 series printer to install the program for my Sony note pad
View 2 Replies View RelatedIm trying to determine the serial number of Gbics already installed and running on a Catalyst 2950 switch. Is there a specific command to do so? There is a command on Catalyst 4506 that gives all info regarding the Gbic ("show idprom interface gi 1/1") Is there something equivalent for 2950?
View 4 Replies View RelatedI am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?
View 2 Replies View RelatedI have a faulty ASA5520 and I am not sure if I have a SMART net contract for it or not (I manage over 200+ ASAs). The problem is that the Serial Number sticker that is normally on the back of the ASA is missing. The ASA5520 is also faulty and doesn't power on so I cannot boot it up and run 'show ver' or similar. If I open the chassis there appears to be other Serial numbers on the Power Supply, and Motherboard etc but they do not seem to be the correct Chassis serial number i.e not in the right format, and if I put them into the Trade tool I get no results.
There must be another record of the serial numbers besides 1x sticker to the rear of the chassis that can fall off? How I can get the chassis serial when the device isn't booting. or (Cisco) is there a way to find the chassis serial number from the power or motherboard serial?
My Sony Vaio was stolen and I dont have any tracking software on it. I was told it can be traced using the serial number this is not going to work as the serial number is not digital is this correct? If so is there any inbuilt device or software ect: that comes installed when you purchase the laptop? I am desperate to find my laptop as it has personal information stored on it of my partner who recently passed away and non of this is replaceable. I would prefer to find it without using the authorities as i know who this person is i just dont know where this person has stored the laptop. It would be best for the authorities not to be involved for my safety.
View 5 Replies View RelatedMy laptop "hp pavillion dm4-1065dx" hass been stolen and i have not installed any theft or tracking related softwares. Kindly tell me how to work dis out and find my laptop.
View 1 Replies View RelatedThis is the second one of the new ASA 55.5X series appliances where I have seen this issue:When I SHOW VERSION, I can see the serial number displayed. However, this does not match the serial number from the sticker affixed to the outside of the chassis.This makes it confusing on opening TAC cases and for updating licenses.
View 8 Replies View RelatedI have 2 2911 routers that will be connected via fiber with an ethernet Gig handoff to each router. Each router will then be connected to local networks on a second ethernet interface on the router. I have always connected routers via serial connections so this is new to me. Outside of the usual ethernet interface addressing configuration, is there anything else that would need to be configured on the 2 routers?
View 1 Replies View RelatedHow do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies View RelatedWhen I insert the TwinGig Converter in a Catalyst 4900M you get the following error message: Failed to read transceiver serial eeprom on port Te2/1, try reinserting.This error is probably because the device expects 10Gig transceivers to be connected to the device not 1Gig.I used the TwinGig 4 module and 8 SFP ports are connected. But when i type in the the "hw-module module <slot> port-group <group> select gigabitethernet" the command is not available. [code]
View 1 Replies View RelatedI have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies View RelatedWhile I managed to connect to each router individually, I decided it was time to connect the routers together via serial; as I don't have any serial cables and need to buy some, what serial cables I need, as well as to ask whether I have the right cards in my router(s) that will allow me to do so.
I bought 3 1841 routers, and all have a 1 port serial WAN Interface Card (WIC 1-T); one router has 2 of these, and one router has a WIC-1B-S/T .. My question is, can I connect the routers with a serial cable via WIC 1-T, or do I need a 2-T
I have two 2950 Switches and am trying to connect via my laptop. My laptop doesn't have a serial port so I am trying to connect through the ethernet port, with a straight through cable and on the end as it goes into the console port I have bought a cisco console rollover adapter.When I turn on terra term I get nothing...just a black screen and it disconnects.
View 6 Replies View RelatedI just finished setting up a bundle of (2) T1's in a multilink bundle and I'm having issues with one of the T1's not wanting to join the bundle.
The router I'm using on the remote office location is a 3620 router running code c3620-i-mz.121-1c.bin
The campus router which is a 7206 is setup the same exact way with multilink 240 and like I've said, serial 0/0 is joined to the bundle just fine, so we are running off one T1 connection.
The serial interface that is not working is: serial 0/1
Here is a show-run:
interface Multilink240
ip address 172.18.xxx.xxx 255.255.255.252
ip route-cache flow
ip ospf network point-to-point
service-policy output PhonesFirst
ppp multilink
[code].....
Our organization currently has a Cisco 4507 acting as our core switch and 2 ASA525 firewalls.
Our existing ISP runs into our 4507. Here is the port config.
interface GigabitEthernet7/1
description ISP-DSL
switchport access vlan 10
[Code].....
We have recently purchased a 5Mbit line with a second ISP and will have the line activated tomorrow. In addition, we recently obtained our AS number through ARIN. How would I configure the second ISP to be used for load balancing/failover?
where can I find a good qualified Tecnical man to connect My Cisco AS 5350 Router to my PRI T1
View 1 Replies View RelatedI am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
We have the need to create a large number of VLANs on one of our networks. We're talking about 60! These will all terminate on a pair of 6509-E switches (building core). We use MSTP as a standard on our network so I'm going to stick with that so that we can dramatically reduce the number of STP instances needed. However, regarding the SVIs (default gateways) is there any reason why creating 60 of these guys would be considerd a big no-no? Or would you expect the 6509s to deal with them like a boss?
View 4 Replies View RelatedOn a Cisco 3560 with IP services ver. 12.2(35)SE5 I have tried to config BGP with a 6-digit AS number, and it is not possible. What software is needed for 6 digit AS number for PI IP addresses, and do I need to buy a new switch also.
View 5 Replies View RelatedWhether Cisco has part number for the large fan in 2811. I know p/n for small fan is already there, but I can't find any for large one( I think it s fan 3).
View 10 Replies View Related