Cisco Switching/Routing :: PPP Multilink Not Coming Up On Serial Interface / 3620 Router?
Nov 1, 2011
I just finished setting up a bundle of (2) T1's in a multilink bundle and I'm having issues with one of the T1's not wanting to join the bundle.
The router I'm using on the remote office location is a 3620 router running code c3620-i-mz.121-1c.bin
The campus router which is a 7206 is setup the same exact way with multilink 240 and like I've said, serial 0/0 is joined to the bundle just fine, so we are running off one T1 connection.
The serial interface that is not working is: serial 0/1
Here is a show-run:
interface Multilink240
ip address 172.18.xxx.xxx 255.255.255.252
ip route-cache flow
ip ospf network point-to-point
service-policy output PhonesFirst
ppp multilink
[code].....
View 3 Replies
ADVERTISEMENT
Oct 2, 2012
I have a CISCO2921. I am not able to bring up its gi0/1 interface. It stays down down.
[URL]
I know that interface is not coming up because of "no media" below. Router#sh int gi0/1 | i media Auto Duplex, Auto Speed, media type is no media
I have tried media rj-45 and media sfp which have also not worked. The other end of this link is ethernet handoff. What is it that I have to do for the link to come up? If I change the connection to gi0/2, I think that will work because I see this for gi0/2:
Router#sh int gi0/2 | i media Auto Duplex, Auto Speed, media type is RJ45
View 10 Replies
View Related
Oct 26, 2012
we are bringing up new ckt and nexus 7000's interface isn't coming up once telco gave a loop. and wee following msg when I do "sh int eth1/1".
(UDLD Tx Rx loop, port: error)
what does "(UDLD Tx Rx loop, port: error)" it mean?before loop. interface was showing as "Link not Connected".
View 2 Replies
View Related
Mar 26, 2012
I have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies
View Related
Oct 22, 2012
While I managed to connect to each router individually, I decided it was time to connect the routers together via serial; as I don't have any serial cables and need to buy some, what serial cables I need, as well as to ask whether I have the right cards in my router(s) that will allow me to do so.
I bought 3 1841 routers, and all have a 1 port serial WAN Interface Card (WIC 1-T); one router has 2 of these, and one router has a WIC-1B-S/T .. My question is, can I connect the routers with a serial cable via WIC 1-T, or do I need a 2-T
View 1 Replies
View Related
Jun 20, 2012
I came across a interesting symptom. Refer to the following topology.
host 1 <-> R1 <-> R2 <-> FW<-> host2
host 1 is configured to send syslog to host2, however due to firewall ACL is not configured, this has caused a spike to 99% in R1 which already has 70% - 80% cpu.
My questions are :
1) Even if the firewall is sending RST back to host 1, it should not caused an 20% cpu increase in R1 cpu. Why this is so? Router model is 3620.
2) How do i prevent this from happening in future? This could potentially allow someone to send random traffic to hosts and cause network performance issue. Is there a way to turn off the RST response from the Firewall? This is an Cisco ASA.
View 1 Replies
View Related
Feb 7, 2012
I have a Cisco 3620 router and I am trying to get internet access. My isp is comcast. All modem lights seem to be operational. But I do not have internet access. I can ping anything other then the router and I am on a home network.
View 47 Replies
View Related
Mar 28, 2012
I am have a little trouble setting up my home lab. I have a 3620 with two ethernet ports and a 3640 with four ethernet ports. I also have a 3500XL switch that I am using to connect the two together, but I can't seem to get each one to ping.
Here are my configs:
3500XL
3500XL-BottomSwitch#show run
Building configuration...
Current configuration:
!
version 12.0
[Code]......
View 14 Replies
View Related
Sep 18, 2012
I just recently bought a new Cisco 2611 for my home lab and am having trouble getting the serial port to work. I have tried multiple things such as erase startup, switching the cables to rule them out, and even changing IP addresses but none worked. [code]
View 1 Replies
View Related
Jul 27, 2006
I config my E0/0 Interface with "ip ospf network non-broadcast" command, I want this interface to use uni cast to hello neighbor.
As I issue "neighbor x.x.x.x" under ospf process, it told me that: OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint networks. I am sure that there are no any typo, and show ip ospf interface e0/0 says it's been an NBMA interface, so what's wrong with this router?
IOS information:
(C3620-J1S3-M), Version 12.3(18), RELEASE SOFTWARE (fc3)
View 7 Replies
View Related
Feb 18, 2013
I have a Cisco 2821 with two serial interfaces bundled using PPP multilink. I want to monitor traffic flow (net flow) on the multilink interface. I have tried configuring ip route-cache flow/ ip flow ingress / egress but no luck.The other thing is when I do sh ip cache flow I guess I should see the multilink interface in both Source and destination columns which is not happening (not showing in destination column).The other router with same config but with ATM sub-interface working properly (same IOS). Are there any hits on this ? Also, is it possible to use SPAN feature ? The monitoring server is at some other site (coming via WAN).
View 1 Replies
View Related
Oct 16, 2011
I have a question regarding mlppp and bonding mpls T1 circuits. For the longest time we have been able to get by on one T1 circuit coming into our 3845 router. Well this T1 has now become congested and they are wanting to add bandwidth to this T1. We connect to the phone company via an MPLS T1 currently. So now it appears as though we are going to purchase another MPLS T1 circuit and bond the two T1's together. The way our network is currently set up, we utilize the same AS number on all of our remote routers regardless of location. Keep in mind I don't have any sort of mlppp set up at this moment, so unfortunately I can't post any configs. I'm just questioning the design portion and how to go about doing this.
Here is where my dilemma begins........
For every MPLS circuit we order on the remote end, we specifiy an IP for the remote router itself and one for the provider to assign to their equipment (the bgp neighbor statements). Now granted i'm no BGP extraordinaire, not even a novice really, but I don't understand how I am going to bring two T1 circuits into the same router (basically with 2 pairs of IP's). In order to bond the two T1's together, i'll need to create a multilink interface and assign an IP to that, but yet I still have 2 SETS of ip addresses. And if that isn't enough of a dilemma, I also need to spedify a neighbor statement in order for my AS to bind to the adjacent provider AS, but yet I have two IP addresses for that as well.
View 2 Replies
View Related
Oct 15, 2012
I am configuring ISDN Interface on 2 Cisco 886VA Version 15.2(3)T . I am unable to set ppp multilink on the BRI0 interface and on the dialer interface. It's like the command doen't exist anymore.How can I fix that so that i can have 128 K bandwidth between ma 2 sites ?.
Router1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router1(config)#int bri0
Router1P(config-if)#ppp multilink
[code]....
View 2 Replies
View Related
May 8, 2012
I have configured multicast (ip pim dense-mode) on two 2911 routers that are connected by a Multilink (3Mbps) Wan connection.The configuration work fine for awhile and sometimes all day but at some point one of the Multilink interfaces stop passing multicast traffic.I perform a sh multilink 1 on the interfaces and one interfaces show the multicast packets incrementing and the other does not, it just stops.The only fix for this is to hard reboot both routers and the multicast traffic begins to flow once again.
View 3 Replies
View Related
Jan 22, 2013
I have hardcoded 1GB ports on 3750X to 1000 and full duplex for all servers connected. THe ports are not coming up with this speed and duplex settings. If I configure them to 100, I am able to see the port is up. Whereas if i connect the same servers to 2950 switches, i can see the ports working fine with 1000 speed ..we have tried with the latest universal IOS as well
View 7 Replies
View Related
Jul 21, 2012
I have 2 ASR routers running PIM-SM between them on several sub interfaces.PIM hello interval configured for 200ms.Sometimes PIM neighbors between ASR routers going down.
Reboot for each router not resolving the problem.Deleting ip pim sparse-mode and configuring it again on one of the ASR routers resolves the problem.
I didn't find any related bug.The version is asr1000rp1-adventerprisek9.03.06.01.S.152-2.S1.bin
View 6 Replies
View Related
Sep 10, 2012
We have recently purchased Catalyst 4510R-E with two PoE line cards. When we connected Cisco Wireless APs to Cat4510 PoE ports it did not come up. These WAPs are working fine on other Cisco switch with PoE ports so there is no issue with WAP. We have received two CAT4510 and on both two slots are populated with PoE line cards and on both switches WAPs are not coming up. PC/desktops are working fine on these ports.Is there any configuration required on Cat4510 to enable PoE feature.
View 15 Replies
View Related
Sep 22, 2012
2801 Router
3550 switch
3500 switch
2 2950 switches
2 pc hosts
Basically I have both PC's pinging 4.2.2.2 DNS, Layer 2, Layer 3 intervlan routing functioning, 2801 Nat is translating, able to ping default gateway of ISP and have configured DNS from what ISP has given under my DHCP scope, however Im still not getting, web pages opening up when i open mazzila or firefox !
View 3 Replies
View Related
Dec 2, 2012
I have a Cisco Catalyst 3100 blade in a Dell server chassis that is trunked to a 6509.
When doing a protocol capture, I see large frames being sent from one of the servers in the chassis.
Example:
TCP:[Continuation to #1701] [Bad CheckSum]Flags=...AP..., SrcPort=HTTP(80), DstPort=2667, PayloadLen=2831, Seq=1489611217 - 1489614048, Ack=1719592331, Win=65535
I see lengths up to 6900+ bites coming from the server.
The switch has the global MTU set to 1500
system mtu routing 1500
and I can't seem to set this at the interface level. The server is configured to send 1500 length frames. Why am I seeing these jumbos? (the server is Windows 2003)
View 2 Replies
View Related
Jun 21, 2012
We are trying to connect 2 nexus 5558UP (5.1.(3)N1(1)) with 10G-SFP+-LR interfaces. The interfaces are not genuine cisco's (smartoptics) but as far as we can tell, they are accepted by the hardware. If we take a look at the optical levels, we can see that the switches can see eachother (double-checked by bringing down one interface to see if optical levels really disappears) on optical level, well within limits. I found a notice about changing debounce timers but this doesn't work, setting it to 0 or 1000 doesn't make a difference. Copies of the different show int commands can be found at the end of this text.
Wim Holemans
Network Services
University of Antwerp
swnxds01-enable# sh int eth1/3 transc details
Ethernet1/3(code)
View 4 Replies
View Related
Apr 6, 2012
Having a strange issue here with an 7606-s chassis equipped with two sup720's, and two regular line cards. There is only one power supply, PWR-2700-AC. I recently builded this setup and powered it on last week for the first time. It ran fine for about 20 minutes while suddenly the chassis powered down.
I've checked the back of the chassis and noticed that the power supply had it's 'input ok' and 'power fail' led lit. I toggled the power switch and waited half an hour to power it on again. This time only 1 minute of joy. My first idea was the PSU due to the power fail led so I had it swapped by the supplier for another. Unfortunately, when I powered it on today, it didn't change a thing, still unexpected power downs.
So I've checked the following documentation: [URL] and followed the suggestion to power the chassis on without any modules in the slots. So I did that and it ran for 8 minutes only. However, the fan tray did respond properly when I removed the small thermal module in the upper right by increasing the fans to full speed.
Following above documentation, it points to the chassis (there is not much left). Now the real question comes, isn't there anything else that could be the cause of this?
View 1 Replies
View Related
Sep 23, 2012
I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this. [code] I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below.[code]
View 4 Replies
View Related
Oct 4, 2011
I have problem with traffic coming from GRE interface and going further through FWSM on the same 6509-E chassis.It's very interesting and confusing. If packets are fragmented, I can go through, however, if I use normal packets (usual ping for example) traffic goes from outside to inside and stops on it's way back.
Here is the detailed info:
WS-C6509-E with WS-SUP720-3B
FWSM HW 4.0, SW 4.1(4)
GRE is done in hardware (source is loopback interface - only one loopback per GRE tunnel).
View 5 Replies
View Related
Dec 10, 2011
How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies
View Related
Oct 16, 2011
I have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 Replies
View Related
May 8, 2011
I have 2 2911 routers that will be connected via fiber with an ethernet Gig handoff to each router. Each router will then be connected to local networks on a second ethernet interface on the router. I have always connected routers via serial connections so this is new to me. Outside of the usual ethernet interface addressing configuration, is there anything else that would need to be configured on the 2 routers?
View 1 Replies
View Related
Sep 7, 2011
IP Address : 192.168.1.0 /24
I need 50 hosts
I need to subnet for f 0/0 and s 0/0
I know for f 0/0 its 192.168.1.1 /26, but after hours and hours i can't seem how to subnet for the s 0/0
View 2 Replies
View Related
Aug 1, 2011
model: SG300-52
version: 1.1.0.73
Switch is running in layer 3 mode.How can I turn off mDNS broadcast coming from the vlan interface on the switch.Getting mDNS broadcast from switch every 5 seconds.
View 1 Replies
View Related
Mar 21, 2012
Is there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies
View Related
Feb 8, 2012
How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies
View Related
Apr 28, 2012
I have a remote site that still utilizes a single T1 connection to me. For multiple reasons we had to scrap the old T1 and have a new one put in. The old T1 resided on a T3 as channel 25. The new T1 is a standlone point to point. I removed the old config from my 7301 and programmed my 3725. I cannot figure out what is going on but the interface stays down/down. There is no loopback turned on, either manually or by the carrier. The AL LED stays amber regardless of whether or not I have a cable patched down. The CD LED remains green when I patch a cable down. LP is not light.I am using a straight through Ethernet cable to connect my 3725 to the smart jack. If you look at the show output below you will see DCD and CTS is down. Since the remote end was working and I just had the tech move the patch cable from one smart jack to another I am assuming the problem is on my side or with the carrierI already tried changing the clock sourced between internal and line. I also swapped out the WIC card for another one. I don't usually program T1 connections. [code]
View 5 Replies
View Related
Jul 30, 2012
When I insert the TwinGig Converter in a Catalyst 4900M you get the following error message: Failed to read transceiver serial eeprom on port Te2/1, try reinserting.This error is probably because the device expects 10Gig transceivers to be connected to the device not 1Gig.I used the TwinGig 4 module and 8 SFP ports are connected. But when i type in the the "hw-module module <slot> port-group <group> select gigabitethernet" the command is not available. [code]
View 1 Replies
View Related
Jun 5, 2013
Where on the case is the serial number located? I have a dead one that needs RMA.
View 1 Replies
View Related
