Cisco Switching/Routing :: C2960S Flexstack Serial Number

Mar 21, 2012

Is there a CLI-command to see the serial number of the flexstack module installed in a C2960S.

View 13 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Need To Know Serial Number Of Sup720

Dec 10, 2011

How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?

View 4 Replies View Related

Cisco Switching/Routing :: AS 5350 XM - Serial Number

Oct 16, 2011

I have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !

View 3 Replies View Related

Cisco Switching/Routing :: Location Of Nexus 1010 Serial Number?

Jun 5, 2013

Where on the case is the serial number located?  I have a dead one that needs RMA.

View 1 Replies View Related

Cisco Switching/Routing :: CatOS 2948G Serial Number - Show Version / Sprom And Sticker Don't

Oct 25, 2012

I am trying to find the serial number on the CLI that matches the serial number sticker on the back of a  WS-C2948G-GE-TX  switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis"  says "Feature not supported."

Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?

View 5 Replies View Related

Cisco Switching/Routing :: Maximum Etherchannels In 2960S Using Flexstack

Oct 25, 2011

how many etherchannels can the 2960S support when it is stacked? I understand it initially has 6 channels.

View 2 Replies View Related

Cisco Switching/Routing :: To Use Flexstack To Stack Two 2960S 48 Port Switches

Oct 11, 2012

I would like to use flexstack to stack two Cisco 2960S 48 Port switches (2960S-48TD-L) for redundancy. Each switch will have a single 10G uplink into our Nexus 7K. One switch in the stack will terminate to linecard 6 (N7K-F248XP-25) and the other switch will terminate to linecard 7 (N7K-F248XP-25). My question is how many flexstack cables are needed? Do I need only one cable or do I need two to connect the two 2960s ?

View 2 Replies View Related

Cisco Switching/Routing :: 2960S 12.2(55)SE3 Flexstack Unable To Configure Etherchannel

Jan 15, 2012

I am trying to configure etherchannel on 2 2960S connected by a flexstack with 2 ports g1/0/52 and g2/0/52 on each 2960.
 
these switch are connected to a CAT4500, I know that I can only use LACP because of cross-stack but when I force the switch to use LACP witch channel-group 2 Mode active the switch do this :

%With PAgP enabled, all ports in the Channel should belong to the same switchCommand rejected (Port-channel2, Gi1/0/52): Invalid etherchnl mode
% Range command terminated because it failed on GigabitEthernet1/0/52
  
I don't know how to bundle the 2 ports on the 2960 stack. each time I use : channel-group 2 mode on there is no error
 
but the switch do this :
 
*Mar  1 00:45:32.290: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2 and will be suspended (trunk mode of Gi2/0/52 is dynamic, Po2 is trunk)
*Mar  1 00:45:32.531: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2

[Code].....

View 9 Replies View Related

Cisco Switching/Routing :: 2960S - FlexStack Module Auth Failed

May 31, 2012

I have been trying to make a stack with two 2960S. They have the same IOS but they behave as they were not connected.One is in production and I am attaching a brand new one to it; in the one that is in production I get these 2 messages:
 
FlexStack Module SmartChip Authentication Failed.I tried switching the modules and the outcome is the same, so I think the modules are ok.What to you recommend, is there a way to bypass this authentication?

View 6 Replies View Related

Cisco :: LMS 3.2 Serial Number Required

Sep 29, 2011

i have LMS 3.2 installed in my campus. i need the serial number of the LMS suite to open a service request with cisco. but unable to find the same. How to find the same.

View 1 Replies View Related

Cisco :: How To Get Ciscoworks LMS 4.0.1 Serial Number

Dec 11, 2011

How to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.

View 2 Replies View Related

D-Link DIR-655 :: Missing Serial Number?

Jun 10, 2012

I'm based in the UK and am using a DIR-655 router but I have no record of its serial number (there is no sticker on the item, and the original box is now missing) - is there any way I can ascertain which version of the router I have? As I understand matters, I need to know this so that I can apply the correct firmware upgrade, which is what I wish to do.

View 1 Replies View Related

Cisco :: OID Used By ASA 55XX Series To Get Serial Number

Mar 1, 2012

What is the equivalent oid as chassisid -  .1.3.6.1.4.1.9.3.6.3.0, which gets the serial number for most cisco switches/routers is for the ASA 55XX series firewalls.

View 2 Replies View Related

Cisco Wireless :: Can Get Serial Number Of SFP In WLC 5508 By GUI Or CLI

Apr 17, 2013

I need to get the serial number of SFP in WLC 5508 ver 7.0 but can't find the command, is this possible and if yes how can I get the S/N of SFF in WLC?

View 4 Replies View Related

Cisco Wireless :: WCS 4.2 - How To Find Serial Number

Feb 8, 2009

We are running WCS 4.2 on linux. I need to find the serial number of the software so I can raise a TAC case. how to find the serial number? I cant see it via the GUI.

View 10 Replies View Related

Cisco Wireless :: View Serial Number Of AP1310 Using GUI?

Nov 24, 2011

I have a problem with an AP1310 which may need me to open a case for RMA. is there any way I can view the serial number using the GUI since the AP is already installed on a high mast but I didn't enable telnet on that?

View 1 Replies View Related

Cisco Firewall :: Find PIX 515e Serial Number?

Sep 27, 2011

How can I find the serial number at Cisco PIX-515E ?

View 2 Replies View Related

Find The Serial Number Of Lexmark Pro 900 Series Printer?

Dec 13, 2011

i need the address of my pro 900 series printer to install the program for my Sony note pad

View 2 Replies View Related

Cisco Infrastructure :: 2950 - Determine The Serial Number On GBIC

Jun 27, 2004

Im trying to determine the serial number of Gbics already installed and running on a Catalyst 2950 switch. Is there a specific command to do so? There is a command on Catalyst 4506 that gives all info regarding the Gbic ("show idprom interface gi 1/1") Is there something equivalent for 2950?

View 4 Replies View Related

Cisco :: View 3750 Stack Serial Number Inventory LMS 3.2?

Oct 17, 2011

I am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?

View 2 Replies View Related

Cisco Firewall :: ASA 5520 - Chassis Serial Number Not In Right Format

Oct 24, 2011

I have a faulty ASA5520 and I am not sure if I have a SMART net contract for it or not (I manage over 200+ ASAs). The problem is that the Serial Number sticker that is normally on the back of the ASA is missing. The ASA5520 is also faulty and doesn't power on so I cannot boot it up and run 'show ver' or similar. If I open the chassis there appears to be other Serial numbers on the Power Supply, and Motherboard etc but they do not seem to be the correct Chassis serial number i.e not in the right format, and if I put them into the Trade tool I get no results.
 
There must be another record of the serial numbers besides 1x sticker to the rear of the chassis that can fall off? How I can get the chassis serial when the device isn't booting. or (Cisco) is there a way to find the chassis serial number from the power or motherboard serial?

View 4 Replies View Related

Sony Vaio - How To Trace Stolen Laptop Via Serial Number

Jan 4, 2012

My Sony Vaio was stolen and I dont have any tracking software on it. I was told it can be traced using the serial number this is not going to work as the serial number is not digital is this correct? If so is there any inbuilt device or software ect: that comes installed when you purchase the laptop? I am desperate to find my laptop as it has personal information stored on it of my partner who recently passed away and non of this is replaceable. I would prefer to find it without using the authorities as i know who this person is i just dont know where this person has stored the laptop. It would be best for the authorities not to be involved for my safety.

View 5 Replies View Related

HP Pavilion Dm4 1065dx - Trace Stolen Laptop Via Serial Number

Jul 9, 2011

My laptop "hp pavillion dm4-1065dx" hass been stolen and i have not installed any theft or tracking related softwares. Kindly tell me how to work dis out and find my laptop.

View 1 Replies View Related

Cisco Firewall :: Serial Number On ASA5555X Do Not Match Show Version

Jan 22, 2013

This is the second one of the new ASA 55.5X series appliances where I have seen this issue:When I SHOW VERSION, I can see the serial number displayed. However, this does not match the serial number from the sticker affixed to the outside of the chassis.This makes it confusing on opening TAC cases and for updating licenses.

View 8 Replies View Related

Cisco Switching/Routing :: C2960S - 12.2(58)SE Crash On SSH

Apr 13, 2011

I just upgraded several of my C2960S-48FPD-L from 12.2(55)SE to 12.2(58)SE and now almost every time I try to SSH to it the switch reboots and gives me these trace backs ... 
 
07:58:52 CST Thu Apr 14 2011: Unexpected exception to CPU vector 200, PC = 1EADA28
-Trace back= 0x1EADA28z 0x1CDC324z 0x1EA5520z 0x1CDC35Cz 0x1CDD0E0z 0x1CDF0C4z 0x1CE06CCz 0x1CE07F8z 0x1D67348z 0x1D611BCz
 
Writing crash info to flash:/crashinfo_ext/crashinfo_ext_3
 
07:58:56 CST Thu Apr 14 2011: Unexpected exception to CPU vector 1100, PC = 121BB98
-Trace back= 0x121BB98z 0x12250FCz 0xFA7540z 0xA807B8z 0xA75DF4z 0xA78080z 0x94B708z 0x9717C0z 0x918DD8z 0x936520z 0x9344BCz 0x9345FCz 0x93484Cz 0x1D67348z 0x1D611BCz

=== Flushing messages (07:58:56 CST Thu Apr 14 2011) ===

Buffered messages: (last 4096 bytes only)
0x00000005  R6 = 0x01224F44  R7 = 0x02A23C6C
000089: *Feb 28 18:03:13.577 CST: %PLATFORM-1-CRASHED: R8 = 0x00000080  R9 = 0x00000000  R10 = 0x00000000  R11 = 0x00000071
000090: *Feb 28 18:03:13.577 CST: %PLATFORM-1-CRASHED: R12 = 0x00034855  R13 = 0x00000280  R14 = 0x01CE0778  R15 = 0x00000000
000091: *Feb 28 18:03:13.577 CST: %PLATFORM-1-CRASHED: R16 = 0x00000000  R17 = 0x00000000  R18 = 0x00000000  R19 = 0x00000000
[ code]....

View 9 Replies View Related

Cisco Switching/Routing :: WS-C2960S Inter VLAN Routing

Dec 9, 2012

I am looking for a reasonable switch but it has do do inter-VLAN Routing. I know I could go with a 3560/3750 with IP Services but I am also thinking the 2960S with IP Base IOS might do?
 
I have looked up the IP Base IOS and it does list IP Routing but how to actually configure inter-VLAN Routing on a 2960S with IP Base?

View 2 Replies View Related

Cisco Switching/Routing :: Enable L3 Routing On C2960S

Apr 19, 2013

I have been trying to enable L3 intervlan routing on C2960S Switch with ip routing command and that was the output from the Switch: [code]

View 6 Replies View Related

Cisco Switching/Routing :: Recommended IOS For Switch C2960S And C3750

Jun 13, 2013

We have several of these WS-C2960S-24PS-L running 12.2(55)SE5  C2960S-universalK9-M and need to upgrade to a better.IOS since we have a sitution where CPU would get to 100% but we have only a few ports connected.Also we have several of WS-C3750-48P running 12.2(55) SE6 C3750-IPBASEK9-M.

View 3 Replies View Related

Cisco Switching/Routing :: 2960 Stack Of Four Ws C2960S Crashes

May 29, 2011

We have a 2960 stack of 4 WS-C2960S-24PS-L switches.Sometimes, at random, the stack crashes and reboots. I have downloaded the crashinfo file and can see the following error.

View 7 Replies View Related

Cisco Switching/Routing :: WS-C2960S-48FPS-L Stack Port Down?

Mar 14, 2013

I'm trying to configure a stack between two WS-C2960S-48FPS-L but does not working.The switch port is always Down.I tried to change de module and cables.I tried to make a loop in one of two switches and the ports always down.
 
IOS: 12.2(55)SE5
 #show switch stack-ports
  Switch #    Port 1       Port 2
  --------    ------       ------
    1          Down         Down

View 15 Replies View Related

Cisco Switching/Routing :: WS-C2960S-24TS-L / Mac Flapping On Stack?

Feb 27, 2012

We have two switches WS-C2960S-24TS-L running in stack with running IOS c2960s-universalk9-mz.122-55.SE3.We have connected two checkpoint devices on Gi1/0/24 and Gi2/0/24 with a simple configuration:
 
interface range GigabitEthernet1/0/24, gi2/0/24
switchport access vlan x
switchport mode access
spanning-tree portfast
 
On the devices log we get the following message:

%SW_MATM-4-MACFLAP_NOTIF: Host 0000.0000.fe21 in vlan x is flapping between port Gi2/0/24 and port Gi1/0/24
 
The mac-address 0000.0000.fe21 is not found on any checkpoint interface. "Show mac-address int gi1/0/24 or gi2/0/24" does not show the correct mac-address of the checkpoint interface connected to the port, but instead shows 0000.0000.fe21.Is there a bug in the IOS, something wrong with the switch config or does it have something to do with the checkpoint config?

View 2 Replies View Related

Cisco Switching/Routing :: Stack C2960S High CPU Version 12.2(58)SE2

Jan 14, 2013

I have a customer with a stack of two switches C2960S-24TS-L that are running 12.2(58)SE2 universal K9, we see that the CPU load increase over time, to 95% and stays there reload solves the problem.the process that akes a lot of CPU is also the SNMP ENGINE, I see that it is running 30 minutes on 95% and then 10 minutes on 35%, this is the only stack were we see this problem. Is there also a SNMP bug in this version ?

View 1 Replies View Related

Cisco Switching/Routing :: GLC-GE-100FX Supported On WS-C2960S-24TD-L?

May 10, 2013

Does GLC-GE-100FX is supported on the WS-C2960S-24TD-L.  I don't see this switch listed under the compatibility matrix.URL
 
But the datasheet for the 2960S says this:
 
"The Cisco Catalyst 2960-S with SFP+ does not support the GLC-FE-100BX, GLC-FE-100FX, or GLC-FE-100LX." But it provides no reference for the GLC-GE-100FX The easy answer is, no the 2960S-24TD doesn't support it, any clarification if possible.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved