I need to get the serial number of SFP in WLC 5508 ver 7.0 but can't find the command, is this possible and if yes how can I get the S/N of SFF in WLC?
View 4 RepliesWe are running WCS 4.2 on linux. I need to find the serial number of the software so I can raise a TAC case. how to find the serial number? I cant see it via the GUI.
View 10 Replies View RelatedI have a problem with an AP1310 which may need me to open a case for RMA. is there any way I can view the serial number using the GUI since the AP is already installed on a high mast but I didn't enable telnet on that?
View 1 Replies View Relatedi have LMS 3.2 installed in my campus. i need the serial number of the LMS suite to open a service request with cisco. but unable to find the same. How to find the same.
View 1 Replies View RelatedHow to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies View RelatedI'm based in the UK and am using a DIR-655 router but I have no record of its serial number (there is no sticker on the item, and the original box is now missing) - is there any way I can ascertain which version of the router I have? As I understand matters, I need to know this so that I can apply the correct firmware upgrade, which is what I wish to do.
View 1 Replies View RelatedWhat is the equivalent oid as chassisid - .1.3.6.1.4.1.9.3.6.3.0, which gets the serial number for most cisco switches/routers is for the ASA 55XX series firewalls.
View 2 Replies View RelatedHow can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies View RelatedI have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 Replies View RelatedHow can I find the serial number at Cisco PIX-515E ?
View 2 Replies View Relatedi need the address of my pro 900 series printer to install the program for my Sony note pad
View 2 Replies View RelatedIs there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies View RelatedIm trying to determine the serial number of Gbics already installed and running on a Catalyst 2950 switch. Is there a specific command to do so? There is a command on Catalyst 4506 that gives all info regarding the Gbic ("show idprom interface gi 1/1") Is there something equivalent for 2950?
View 4 Replies View RelatedI am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?
View 2 Replies View RelatedI have a faulty ASA5520 and I am not sure if I have a SMART net contract for it or not (I manage over 200+ ASAs). The problem is that the Serial Number sticker that is normally on the back of the ASA is missing. The ASA5520 is also faulty and doesn't power on so I cannot boot it up and run 'show ver' or similar. If I open the chassis there appears to be other Serial numbers on the Power Supply, and Motherboard etc but they do not seem to be the correct Chassis serial number i.e not in the right format, and if I put them into the Trade tool I get no results.
There must be another record of the serial numbers besides 1x sticker to the rear of the chassis that can fall off? How I can get the chassis serial when the device isn't booting. or (Cisco) is there a way to find the chassis serial number from the power or motherboard serial?
My Sony Vaio was stolen and I dont have any tracking software on it. I was told it can be traced using the serial number this is not going to work as the serial number is not digital is this correct? If so is there any inbuilt device or software ect: that comes installed when you purchase the laptop? I am desperate to find my laptop as it has personal information stored on it of my partner who recently passed away and non of this is replaceable. I would prefer to find it without using the authorities as i know who this person is i just dont know where this person has stored the laptop. It would be best for the authorities not to be involved for my safety.
View 5 Replies View RelatedMy laptop "hp pavillion dm4-1065dx" hass been stolen and i have not installed any theft or tracking related softwares. Kindly tell me how to work dis out and find my laptop.
View 1 Replies View RelatedThis is the second one of the new ASA 55.5X series appliances where I have seen this issue:When I SHOW VERSION, I can see the serial number displayed. However, this does not match the serial number from the sticker affixed to the outside of the chassis.This makes it confusing on opening TAC cases and for updating licenses.
View 8 Replies View RelatedWhere on the case is the serial number located? I have a dead one that needs RMA.
View 1 Replies View RelatedI am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
which is the maximum number of simultaneous wired guest clients on a 5508? And in a 2112 controller?
Wired clients count as wireless clients??
What about anchoring limitations, what is the effect of wired guest clients on the anchor controller?
I've searched the release notes for 7.2+, but I haven't found a documented number of how many active RF Profiles a 5508 can support. Any limitation of how many RF Profiles they can have?
View 3 Replies View RelatedI have some tunnels which terminate to my home router. I'm allowing the other ends of the tunnels to use my voice setup. I need to prepend *67 to all called numbers which don't originate from my house. I don't want people calling my home number based on the caller-id number they see when someone across one of the tunnels calls.
So if 5008 calls 212-333-4444 I want it sent to my provider as *672123334444. If 5001 calls a number, I don't want it touched. Can I do this? I can use IOS or CUCM here.
just ran a discovery on a large network and found 49 wireless controllers (5500, 4400 and 2000 series) and none of them are showing the controller serial number. They are all running 7.0.235.0 and I found no bugs that match this issue.
View 1 Replies View RelatedOn the WAN port, there are 4 pins that are traced to the internal serial traces. Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end. It may be called a Cisco Debug Adapter, but we haven't been able to find?
View 9 Replies View Relatedcan i use a cat 5 cable to extend a 9 pin serial cable to connect my PC to my home audio controller? I have a serial to USB converter but my PC is upstairs and my audio component is downstairs?
View 1 Replies View RelatedI am trying to set up a Linksys WAP4410N on our network. We are trying to run it using unrestricted access, but it is requiring a pin number. The prompt I get when trying to connect to the WAP is that the number should be in the original documentation. I can not find the original documentation and I cannot log into the WAP to find the PIN number.
View 1 Replies View RelatedI have a customer who is going to deploy a WLC HA AP SSO setup. I have recommended them to have 4 Gigabit SFP modules in each WLC5508.The customer now asks if it is possible to only have one or two SFP modules in the standby unit ? As he says it is properly not going to go in service one time within the next five years if he is unlucky.
View 5 Replies View RelatedMy customer wants to buy AIR1242AG with 2.4 GHZ antennas which are not ceiling mounted. How many 2.4 GHz antennas I can have on the AIR1242AG?
Can I have a recommendation which antenna I should use which is not ceiling mounted?
I have configured four E1 links between two locations on my 3745 using WIC-2T cards. At both ends all the serial links are configured as ip unnunmbered fastethernet 0/0 encapsulation ppp OSPF is enabled without CEF I would like to know how load balancing will occur in this scenario?Will all my links be utilised at the same time? Will multiple links be used only when the need (in terms of bandwidth) arises?
View 3 Replies View RelatedI understand that IPv6 uses the MAC address of a LAN interface to make up the EUI-64 of a serial interface since serial interfaces don't have MACs. What happens when there is no LAN interface available? What if the switch has only serial interface cards?
View 2 Replies View RelatedWere bringing up a new site shortly and I'm trying to configure Serial0/0/0 which will be connected to an MPLS over 1.5m T1 line. I am basically doing a simular configuration as other sites where one of the ethernet interfaces is handed off from a fiber optic wan, but a T1 MPLS is connected to a WIC card and this provides a redundant path (though slower) in case of a fiber cut or equipment failure. This should be pretty straightforward but it appears as if I have no serial interface on this router. Card is in and everything, it is a VMIC-3-1MFT-T1/E1 in EHWIC 0.
View 7 Replies View RelatedMy sister had Time Warner road runner cable hooked up today. They gave her a Ubee combo modem and router in one box. When she tries to connect, it does not show up on the list of wlan connections in taskbar. I went thru network settings to try and set up the Ubee and it pops up in a few seconds, then tells you to hit next button and then ask for a 4 to 8 digit pin number which it says is on the modem.
View 1 Replies View Related