Cisco WAN :: Can't Configure Serial Int On 2911/K9
Feb 1, 2012
Were bringing up a new site shortly and I'm trying to configure Serial0/0/0 which will be connected to an MPLS over 1.5m T1 line. I am basically doing a simular configuration as other sites where one of the ethernet interfaces is handed off from a fiber optic wan, but a T1 MPLS is connected to a WIC card and this provides a redundant path (though slower) in case of a fiber cut or equipment failure. This should be pretty straightforward but it appears as if I have no serial interface on this router. Card is in and everything, it is a VMIC-3-1MFT-T1/E1 in EHWIC 0.
View 7 Replies
ADVERTISEMENT
Jun 14, 2011
From all of the documentation I am seeing, the 2911 does not support the NM-E3/T3 serial card.
View 16 Replies
View Related
May 8, 2011
I have 2 2911 routers that will be connected via fiber with an ethernet Gig handoff to each router. Each router will then be connected to local networks on a second ethernet interface on the router. I have always connected routers via serial connections so this is new to me. Outside of the usual ethernet interface addressing configuration, is there anything else that would need to be configured on the 2 routers?
View 1 Replies
View Related
Aug 20, 2011
I have recently purchased 2911 routers running 15.1 to replicate a system I had implemented using 2811 routers running 12.4 a few years ago. None of my applications and servers have changed, but trying to determine why my router access-list on my serial links are not behaving the same. I don't keep up with Cisco changes.
On my original system, which is a private network that distributes a lot of udp broadcast and multicast data to remote sites over 64k serial lines, I manage some of the udp broadcast data using access-lists. When I check on my 2811-based system, "show ip access-list" shows a nice distribution of filter hits showing my expected deny/permit access-list entries working as expected allowing me to filter the particular udp broadcast ports of interest on the various serial interfaces.
On my 2911 based system, with most other elements the same, the access-list is not working correctly, and I see data getting through the access control to the other side of the serial link. Using tcp dump and other tools on the remote systems my routers attach to, it looks like the access control is basically ignored... though if I "shutdown / no shutdown" the serial link between the routers, it definitely stops and restarts the flow of data, so I know data is traveling over that interface... when I run "show ip access-list" on the 2911, I see tons of hits on one deny filter, and the last "ip permit any any" filter, but other deny udp any any eq XXX port filters are simply not registering denies.. which should be triggering since I see my server sending the data, and my client systems receiving the extra data I am supposed to be filtering on the router...
Is there potentially a new feature or command set option that I am missing to correctly filter outbound data from my serial links?
On 2811 w/ an
HWIC 4A/S int s0/0/0
ip access-group sample1 out
ip access-list extended sample1
{code]...
View 2 Replies
View Related
Dec 21, 2011
What specific commands are needed to configure qos on a router?
Two sites:
Cisco 2911 (site 1 ) Cisco 2911 (Site 2)
Data Vlan
Management Vlan
I want to configure QOS on Site 1 where the Data Vlan traffic is always marked higher than the management Vlan coming from Site 1.
View 1 Replies
View Related
Dec 27, 2012
I have one router 2911 with the following image c2900-universalk9-mz.SPA.151-4.M4.bin I have two IPS on this routers and I tried to configure the IP SLA on this and I`m not able to do it and I don´t know why. I can configure almost everything but not the IP SLA command.this is the config:
track 10 ip sla 1 reachability
delay down 10 up 1
!
track 20 ip sla 2 reachability
delay down 10 up 1
!
[code]....
What I need to do in this case? or why cannot configure the IP SLA?
View 5 Replies
View Related
May 19, 2011
I've got a 2911 with a primary ethernet link to the ISP, with BGP running over it. There's also an ADSL module in it, which will connect into the same ISP AS. how do i configure BGP over the ADSL so that it sits there doing nothing until the primary link fails? Do i need to setup a new instance of BGP with a different AS on the router or can it sit in the same AS as the primary link?
View 1 Replies
View Related
Jun 21, 2011
Suppose a broadcasted IP packet reaches one of the integrated RJ-45 ports on a 2911 ISR G2, will it be possible to configure the router so that the other integrated RJ-45 ports, ESM/EHWIC modules installed on the router, as well as the MGF also recieve the packet? Technically, the router should act similar to a switch with the SRE behaving similar to a seperate machine connected via the MGF and other external machine connected to the ports of the router to recieve the broadcasted packet.
Also, if SNMP traps were generated from the router,Will it be possible to send the traps from the router via the MGF to the SRE installed on the router?
View 1 Replies
View Related
Sep 19, 2012
I need to configure two links (active and failover) on router 2911. Do I need DATA LICENSE to configure this with static router and route-map?
View 4 Replies
View Related
Mar 6, 2012
what will be the work around on this configuration.currently we have a Lease Line connection on serial interfaceISP <=SERIAL=>Router 2911<=ACCESS MODE=>Firewall(DATA DHCP SERVER located here, policy implemented here)<=TRUNK MODE=>CORE Switch(VLAN Assignment is here)<=TRUNK MODE=>ACCESS Switch(DATA and VOICE passess thru each ports)i am thinking to create a DHCP pool on the router to where my firewall should point to and from the DHCP pool it will point the internal network going to public network.
View 2 Replies
View Related
Dec 19, 2011
We have a Cisco 2911 Router and have configured via BT Infinity Broadband for out going internet access etc. Are there any incoming restrictions ACL settings etc. that will stop us using for ISA VPN, Exchange connections, Intranet, Sharepoint etc. We have reserved 13 Static IP Addresses from the ISP.
View 1 Replies
View Related
Jan 29, 2012
I have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
View 6 Replies
View Related
Jun 17, 2012
Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies
View Related
Jul 25, 2011
I see that Application protection - blocking peer-to-peer file sharing traffic is a capability of Cisco IOS Firewall. How do i configure my Cisco 2911 ISR to block peer-to-peer file sharing traffic?
View 1 Replies
View Related
Dec 29, 2012
Is there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
View 3 Replies
View Related
Dec 25, 2011
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
View 2 Replies
View Related
May 24, 2012
can i use a cat 5 cable to extend a 9 pin serial cable to connect my PC to my home audio controller? I have a serial to USB converter but my PC is upstairs and my audio component is downstairs?
View 1 Replies
View Related
Feb 6, 2013
I have configured four E1 links between two locations on my 3745 using WIC-2T cards. At both ends all the serial links are configured as ip unnunmbered fastethernet 0/0 encapsulation ppp OSPF is enabled without CEF I would like to know how load balancing will occur in this scenario?Will all my links be utilised at the same time? Will multiple links be used only when the need (in terms of bandwidth) arises?
View 3 Replies
View Related
Sep 9, 2012
I understand that IPv6 uses the MAC address of a LAN interface to make up the EUI-64 of a serial interface since serial interfaces don't have MACs. What happens when there is no LAN interface available? What if the switch has only serial interface cards?
View 2 Replies
View Related
Sep 29, 2011
i have LMS 3.2 installed in my campus. i need the serial number of the LMS suite to open a service request with cisco. but unable to find the same. How to find the same.
View 1 Replies
View Related
Dec 11, 2011
How to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies
View Related
Nov 23, 2011
I think the crappy usb to serial cable from china broke because when i boot up my cisco router, after it decompose the IOS image and shows all the interface links, it won't do anything. I can't get to user exec mode.anyways, i think my usb to serial cable is faultily. I got one that is from ebay for like 2 bucks and i think it is the reason why i can't even connect to my router now
View 3 Replies
View Related
Sep 7, 2011
IP Address : 192.168.1.0 /24
I need 50 hosts
I need to subnet for f 0/0 and s 0/0
I know for f 0/0 its 192.168.1.1 /26, but after hours and hours i can't seem how to subnet for the s 0/0
View 2 Replies
View Related
Apr 23, 2013
Any good way to force a serial link to delay packets to simulate a hi latency WAN link? Found this command so far:
Router(config-if)# transmitter-delay hdlc-flags
I can dial the speed up/down via clock rate all good but I need to also simulate latency. This is for simulating a WAN bonding scenario so I was going to aggregate a 10M ethernet port with a 2M serial and a 512k serial. But I need to also ensure varying latency.
View 2 Replies
View Related
Jan 22, 2012
Any good way of depicting serial links in Visio? Manually drawing is pretty clunky and quick searches in google isn't turning up much.
View 10 Replies
View Related
Dec 29, 2012
How to know the serial 0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 12 Replies
View Related
Apr 11, 2006
How to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 4 Replies
View Related
Oct 21, 2004
I have a cisco router 2621 when i install the module cisco NM4T it is not detectetd. following are the outputs.i have tried IOS 12.2.15T15 & 12.3
booting up:
smart init is sizing iomem
ID MEMORY_REQ TYPE
0000A2 0X00103980 C2600 Dual Fast Ethernet
[Code]......
View 4 Replies
View Related
May 7, 2013
I am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.
I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.
View 4 Replies
View Related
Apr 20, 2011
We have a wan serial connection connected to cisco router 1750, and we want to upgrade the serial connection to ethernet but we haven't any additional ethernet interface on the router. Is there any converter from ethernet to serial?
View 8 Replies
View Related
Apr 28, 2012
I have a remote site that still utilizes a single T1 connection to me. For multiple reasons we had to scrap the old T1 and have a new one put in. The old T1 resided on a T3 as channel 25. The new T1 is a standlone point to point. I removed the old config from my 7301 and programmed my 3725. I cannot figure out what is going on but the interface stays down/down. There is no loopback turned on, either manually or by the carrier. The AL LED stays amber regardless of whether or not I have a cable patched down. The CD LED remains green when I patch a cable down. LP is not light.I am using a straight through Ethernet cable to connect my 3725 to the smart jack. If you look at the show output below you will see DCD and CTS is down. Since the remote end was working and I just had the tech move the patch cable from one smart jack to another I am assuming the problem is on my side or with the carrierI already tried changing the clock sourced between internal and line. I also swapped out the WIC card for another one. I don't usually program T1 connections. [code]
View 5 Replies
View Related
Mar 1, 2012
What is the equivalent oid as chassisid - .1.3.6.1.4.1.9.3.6.3.0, which gets the serial number for most cisco switches/routers is for the ASA 55XX series firewalls.
View 2 Replies
View Related
Feb 2, 2012
I have been getting alerts on unused serial ports on my routers as being operational down. How can I stop these alerts?
View 5 Replies
View Related