I've got a 2911 with a primary ethernet link to the ISP, with BGP running over it. There's also an ADSL module in it, which will connect into the same ISP AS. how do i configure BGP over the ADSL so that it sits there doing nothing until the primary link fails? Do i need to setup a new instance of BGP with a different AS on the router or can it sit in the same AS as the primary link?
View 1 Replies
what will be the work around on this configuration.currently we have a Lease Line connection on serial interfaceISP <=SERIAL=>Router 2911<=ACCESS MODE=>Firewall(DATA DHCP SERVER located here, policy implemented here)<=TRUNK MODE=>CORE Switch(VLAN Assignment is here)<=TRUNK MODE=>ACCESS Switch(DATA and VOICE passess thru each ports)i am thinking to create a DHCP pool on the router to where my firewall should point to and from the DHCP pool it will point the internal network going to public network.
View 2 Replies View Relatedi will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.
View 1 Replies View RelatedWhat specific commands are needed to configure qos on a router?
Two sites:
Cisco 2911 (site 1 ) Cisco 2911 (Site 2)
Data Vlan
Management Vlan
I want to configure QOS on Site 1 where the Data Vlan traffic is always marked higher than the management Vlan coming from Site 1.
I have one router 2911 with the following image c2900-universalk9-mz.SPA.151-4.M4.bin I have two IPS on this routers and I tried to configure the IP SLA on this and I`m not able to do it and I don´t know why. I can configure almost everything but not the IP SLA command.this is the config:
track 10 ip sla 1 reachability
delay down 10 up 1
!
track 20 ip sla 2 reachability
delay down 10 up 1
!
[code]....
What I need to do in this case? or why cannot configure the IP SLA?
Were bringing up a new site shortly and I'm trying to configure Serial0/0/0 which will be connected to an MPLS over 1.5m T1 line. I am basically doing a simular configuration as other sites where one of the ethernet interfaces is handed off from a fiber optic wan, but a T1 MPLS is connected to a WIC card and this provides a redundant path (though slower) in case of a fiber cut or equipment failure. This should be pretty straightforward but it appears as if I have no serial interface on this router. Card is in and everything, it is a VMIC-3-1MFT-T1/E1 in EHWIC 0.
View 7 Replies View RelatedSuppose a broadcasted IP packet reaches one of the integrated RJ-45 ports on a 2911 ISR G2, will it be possible to configure the router so that the other integrated RJ-45 ports, ESM/EHWIC modules installed on the router, as well as the MGF also recieve the packet? Technically, the router should act similar to a switch with the SRE behaving similar to a seperate machine connected via the MGF and other external machine connected to the ports of the router to recieve the broadcasted packet.
Also, if SNMP traps were generated from the router,Will it be possible to send the traps from the router via the MGF to the SRE installed on the router?
I need to configure two links (active and failover) on router 2911. Do I need DATA LICENSE to configure this with static router and route-map?
View 4 Replies View RelatedHow to configure wifi adsl 450tc1 router
View 1 Replies View RelatedWe have a Cisco 2911 Router and have configured via BT Infinity Broadband for out going internet access etc. Are there any incoming restrictions ACL settings etc. that will stop us using for ISA VPN, Exchange connections, Intranet, Sharepoint etc. We have reserved 13 Static IP Addresses from the ISP.
View 1 Replies View RelatedI have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
How can I configure the Cisco 515E (version 6.3(4)) to be used with ADSL modem. Currently the compuerters are directly connected to the ADSL modem to get the priviate IP addresses and we would like to add the Cisco firewall after the ADSL modem.
ADSL Modem ---> Firewall --> Switch--> Computers
Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies View Relatedto configure beetel 450tc1 wifi router with tikona broadband connection.
View 3 Replies View RelatedI want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
My network topology is like this :
ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
2. I configure Vlan1 to use the network configured on my modem :
interface Vlan1
ip address 172.16.0.1 255.255.255.248
3. I try to ping my devices :
#ping 172.16.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!
[code]....
I see that Application protection - blocking peer-to-peer file sharing traffic is a capability of Cisco IOS Firewall. How do i configure my Cisco 2911 ISR to block peer-to-peer file sharing traffic?
View 1 Replies View RelatedIs there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
I have a Cisco 857 router which i used for Internet connection with RJ11 connectior (ADSL0 POTS) but now the ISP has changed the internet link with PPOE type and the ONT connection is RJ45 , Is there a possibility to configure one os the Fast Ethernet ports as WAN port for internet.
View 2 Replies View Relatedi have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedI am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
I am looking at this doc to use an ASA + 2911 to do Policy Based Routing with multiple ISPs.From the linked doc, under the PBR scenario, what should the IP addresses be for the routers connection to the ISPs? It isnt labeled.
View 4 Replies View RelatedI have a cisco 2911 router that is located in my head office LAN and I use this router to connect to my branch networks. I want to configure IP SLA Monitor on this router to track my WAN Links but it does not support the command IP SLA Monitor. My IOS VERSION is c2900-universalk9-mz.SPA.151-2.T1.bin. how I can configure IP SLA on my router.
View 4 Replies View RelatedI have a router Cisco 2911 with two possible Wan interfaces out and a backup configuration using IP SLA. When the Primary Interface goes down the traffic is automatically rerouted through the Backup Interface, but the problem I have is that when the traffic is going through the Backup Interface (because the Primary is down) if the Backup Interface also goes down, if the Primary goes up, the traffic is not automatically rerouted to the Primary Interface. And it looks to me like it keeps trying to goes out the Backup Interface and cannot see that the Primary is down. I guess that the pings are going out the backup Interface and as it is down the router doen't receive any anwer to the ping and doesn't change to the Primary.
The main configuration related to the IP SLA is this:
!
track 1 ip sla 1 reachability
!
interface GigabitEthernet0/0
description backup Interface
ip address 175.xx.xx.10 255.255.255.252
ip nat outside
[Code]....
We have 2911 with HWIC-4ESW. System image file is "flash0:c2900-universalk9-mz.SPA.152-1.T1.bin"_2911#sh inv NAME: "CISCO2911/K9 chassis", DESCR: "CISCO2911/K9 chassis" PID: CISCO2911/K9 , VID: V05 , SN: FGL16011005
[Code]....
The problem was that HWIC-4ESW no longer pass traffic although showing that the interfaces are up rebooting the router solved the problem. What IOS is more stable and not subject to this problem?
Recently i attempted to build a LAN 2 LAN VPN tunnel from an Asa to a 2911 running zone based firewall. This was a standard IPSec psk tunnel nothing fancy. I got the tunnel to establish but i could only get traffic to encap on the Asa side and decap on the 2911 side. I couldn't get return traffic.I followed this doc here for classic IPSec in the last example. URL
And I am sure the Asa is right I built a ton of those but I am new to zfw. I did not see anything about a NAT exempt rule. But since everything uses real IPs instead of NAT I wasnt sure and I could not find any info. Do I need to do NAT exempt? If so do you use a route map on the end of you NAT overload config line like in the past?
Also I have a zone-pair to "self" and I was not sure if I needed anything there to be able to ping the inside interface of the 2911 when the tunnel is up from the remote end.
I have to build HA environment, at the moment we have only one R1 and WAN1 but company wants to buy R2 + WAN2 and have HA between the routers, in case R1 or WAN1 goes down the other router will take over.
What would be standard methodology nowadays to do that - does HSRP will do what I need or it is better do some other way?
What are the max number of T1's that can be bundled on a 2911 router?
View 0 Replies View RelatedI need a interface v.35 on 2911 router, but it does not have WIC slot, it has EHWIC. Could some one told me if there are a card with V.35 interface that I can install in this model of router?
View 2 Replies View RelatedI have the following setup where the Cisco ME 3400 provided by the ISP.
My Cisco 2911 is configured as below:
CORE_Router#sh run
Building configuration...
Current configuration : 6075 bytes
[Code].....
I have a problem I am running into... I replaced a 2621 with a 2911. The 2911 has three interfaces and I need to use all of them... Description:
gige0/0 dhcp static IP from ISP, public IP, they assign me 4 more usable public IPs gige0/1 broken into four VLANS, 108, 109, 120, 127, ip nat on 109 for them to get to the internet, and a static translation on 127 for the phone system to get to the internet gige0/2 assigned another public IP. A tenent has a linksys router on this interface, they want a public IP.
The problem is that this setup worked, but when we moved to the 2911, some nat translations are failing, and we would like to figure out how to minimize the number of public IPs we use (right now it is three + the static assigned dhcp). The nat that is not working is the nats to the 2001-3001 range. I am not sure why it is failing, but the router seems to indicate it thinks some of these overlap. This router is also doing a vpn to an asa... that seems to be working fine.
Current config:
Current configuration : 6072 bytes
!
! Last configuration change at 14:31:44 UTC Thu Aug 2 2012
! NVRAM config last updated at 14:31:50 UTC Thu Aug 2 2012
[Code]....
I thing that i find some bug in the newest IOS 15.1.4M.
The case is falow:
I start to configure failover for the costomer - make default route, make the default path but i cant find the comand IP SLA monitor. Is some meet this problem with this IOS or just Cisco make some chenge in the CLI commands?
Tomorrow i will try with IOS version 15.1.1T.
I have a 2911 router that I am trying to use a h.323 gateway for faxing purposes.Right now I can 4 digit dial and 10 digit the number and my analog phone answers, but when I try to place a call I get a fast busy immediately (as soon as I pick up the receiver)
View 1 Replies View RelatedI want to connect a RPS2300 to a Cisco 2911 router to provide power backup.I have two questions ,Easy one : if the 2911 PSU (internal Power Supply Unit) fails, how to confirm the RPS2300 provides power to the 2911 with no reboot of the 2911 ?,Tricky one : After we replace the broken PSU, will the 2911 reboot or not as power revert from RPS2300 to internal PSU ?
View 4 Replies View Related
