I want to connect a RPS2300 to a Cisco 2911 router to provide power backup.I have two questions ,Easy one : if the 2911 PSU (internal Power Supply Unit) fails, how to confirm the RPS2300 provides power to the 2911 with no reboot of the 2911 ?,Tricky one : After we replace the broken PSU, will the 2911 reboot or not as power revert from RPS2300 to internal PSU ?
View 4 RepliesWhen using dynamic configuration tools, if I choose 2960 (not 2960s), I have the option to choose RPS2300 as redundant power, but when I choose 2960s, I cannot choose RPS2300. However, in a document describe both 2960 and 2960s, it said that RPS2300 can be used. Does RPS2300 support 2960S?
View 1 Replies View RelatedHow many C3K-PWR-750WAC units in PWR-RPS2300 do I need for router CISCO2921-HSEC+/K9?
View 3 Replies View RelatedI know the white papers say that the RPS 2300 supports the 3750-E series and the 3750 series, but we have 3750-G and -X series. Wanted to make sure that these switches are supported and if we need anything special?
View 3 Replies View Relatedgot a RPS2300 with 4 cat3750g48ts on it (yeh I know - Cisco documentation allows only 2 of them ). What will happen if I connect an additional Cisco 2921 router?
View 0 Replies View RelatedI am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
I need a interface v.35 on 2911 router, but it does not have WIC slot, it has EHWIC. Could some one told me if there are a card with V.35 interface that I can install in this model of router?
View 2 Replies View RelatedI have a 2911 router that I am trying to use a h.323 gateway for faxing purposes.Right now I can 4 digit dial and 10 digit the number and my analog phone answers, but when I try to place a call I get a fast busy immediately (as soon as I pick up the receiver)
View 1 Replies View RelatedWe can't seem to SSH from the outside network into our router. Our router config looks straight forward enough.
!
! Last configuration change at 10:41:22 zone Thu Mar 15 2012 by tssconsult
! NVRAM config last updated at 11:19:12 zone Thu Mar 15 2012 by tssconsult
!
[Code].....
Recently they bought a new Cisco 2911 router and told me that they want it connected to an outside WAN connection that they hadn't used in a while so they could create a little network on the side. They want to just plug the server into the router and go. Unfortunately, I am sort of clueless about how to set up the config for it.
There are 3 GE ports, with the line from the outside coming in on GE0/0. I've already activated the interface and it is up, but that's where I get stuck.
I am connected to my internet with
WAN Interface
gig0/0 interface
ip add 62.x.x.x 255.255.255.252
duplex full
speed auto
LAN interface
gig0/1
ip add 10.x.x.x 255.255.255.0
duplex full
speed 100 ( i am keeping the speed 100 because it is connected in switch port f0/48,made the switch port as speed 100)
but after some time my connection to the internet goes off and i just shut and no shut the WAN interface and it comes back.
i have problem with a router 2900 with a card switch 16 ports (sm-es2-16p) that does not doing the intervlan routing. i have attached 2 show tech one of the router and one of the card switch 16 ports (sm-es2-16p). I connected physically the switch card to a router interface and it seem to be working because i can do a ping from my pc ( in user vlan 26) to my gateway on the router (172.20.26.1) but i can not do ping to the others vlan like (172.10.26.1) or others. .. i want to know what is happening and if it there is a way to do the trunk conectivity between the switch card and the router internally without a phyisical connection.
View 4 Replies View Relatedi am trying to upgrade the firmware in my C2960 switch to 15(1) SE2, and i get the error: Failed to execute the command archive download -sw /overwrite /http iosFile.
View 10 Replies View RelatedDoes the 2911 router support the ability for Netflow V5 to pass through GRE tunnels? I can't seem to find any documentation that indicates this.
View 2 Replies View RelatedI enable the IPS on the 2911 router . I am using the Basic IPS signatures that are inbulid on the routers . But sill it showing , that no signature is active .
ip ips signature-category
category all
retired true
ip ips signature-category
category ios_ips basic
retired false
[code]....
Suppose a broadcasted IP packet reaches one of the integrated RJ-45 ports on a 2911 ISR G2, will it be possible to configure the router so that the other integrated RJ-45 ports, ESM/EHWIC modules installed on the router, as well as the MGF also recieve the packet? Technically, the router should act similar to a switch with the SRE behaving similar to a seperate machine connected via the MGF and other external machine connected to the ports of the router to recieve the broadcasted packet.
Also, if SNMP traps were generated from the router,Will it be possible to send the traps from the router via the MGF to the SRE installed on the router?
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]
We are having 3 internet connections coming in to one of our customer's main offices for redundancy and etc. I would like to replace the 3 routers with a one for easier support and management. One of the connections is an ADSL and the other 2 are leased lines so they terminate with an RJ45 connection.
Would something like a Cisco 2911 + HWIC ADSL card be sufficient enough or would you recommend something else?
We have an old Cisco 2600 series router, running a single T-1 line, AT&T is the carrier. Very standard stuff.
The T-1 works perfectly on the old router. Cisco 2600 with a WIC-1DSU-T1 card. We have a brand new 2911 router with a VWIC3-1MFT-T1/E1 card in it. The circuit runs 100% clean and trouble free on the old router. When I plug it into the new router, it shows up/up but has a massive number of errors on the line, and the circuit is not usable. There are no timing slips or anything like that.
I have another site using the same router and card with the same configuration on that T-1 and it works perfectly. Zero errors. This site (in a different city) is totally slammed with errors. We already replaced the T-1 card and still have the exact same issue.
I've actually been doing this a long time, and I've tried all of the usual things, adjusting line build out, changing clock source, checking and re-checking configs. Nothing seems to reduce the error rate.
I personally think it has something to do with the Smartjack. Like maybe their LBO is too high or too low, and the old router card was more/less sensitive than the new one?
This is a layer 1 issue and is not defective hardware or defective configuration. I am looking for T-1 insights or bugs/issues.
Im getting flooded with the following messages: Feb 14 10:47:19.740 EST: PLATFORM-5-ECC_MSG: A corrected single bit error has occurred in L2C Data Cache at location 0x294.
[Code]...
We bought a cisoc 2911 Router with an EHWIC-VA-DSL-A Card. I did the Dialer Setup without any problem but if i set the ATM interface with the commands: [code]The Router crashes after some seconds. I didn't connceted the phone line to the DSL card. [code]
View 5 Replies View RelatedI was wondering what is the router performance decrease when using encryption?
For instance the CISCO2911 has 180.73Mbps half duplex switching performance, what would be more or less the decrease in performance if I use encryption?
Putting in a 1Gbps private Ethernet link between 2 sites. Currently have 2 2811's at each location, don't think that will cut it.
I was going to get 2 2911's, but looking at the docs it looks like they can only do 180mbps of throughput? Am I way out of my league here?
We have a router 2911 recently purchased which supports vpn but we are not able to do vpn tunneling, So what is required to use VPN connection.
Does ios has to upgrade or some kind of license is required.If license is required then what kind of license.Router version is 15.0(1r) M15 which I found in sh version command.
I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
Here is the document I was referencing
[URL]
I have following scenario - router 2911 connected to 2950 switches with about 80 vlans. How can I limit speed on each of the 79 vlans (to equal % acros all of them) and give vlan 80 lets say 30% of total bandtwith. Since I am new to QOS, can you point me to the right website or give me example.
View 4 Replies View RelatedIn my test lab I can't to make work my webvpn configuration = I have several components: MS AD, MS CS (but without NDES), router 2911 and client computer. Client and router have a certificate from MS CS. In my configuration I use authentication by certificate or aaa (LDAP) and authentication by aaa working good. But authentication by client certificate doesn't work. And my internal https services don't work also - "Invalid or no certificate", but this strange because I imported CA certificate for this.
My 2911 version: Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(3)T, RELEASE SOFTWARE (fc1)
My Config:
aaa authentication login webvpn group ldap local
ip local pool webvpn 192.168.200.1 192.168.200.254
bind authenticate root-dn cn=webvpn,ou=staff,dc=domain,dc=com password P@ssw0rd
webvpn gateway vpn
ip address <ip address> port 4443
ssl trustpoint root-ca
[code].....
i'm trying to install the security licenses on a 2911 router and is giving the error shown in the attached file
View 4 Replies View RelatedWhat is the configuration for allow port from Outside to inside( 80,21,https...) and i want to allow traffic from outside to inside only 80,https and 21.
View 1 Replies View RelatedI have a problem with my internet speed when i use cisco router 2911, the speed is very low. when use the ADSL router of my ISP ( the router is CNET), i don't have probleme. all test that i have do is without my lan juste 1 computer connected to routers.
I have HWICADSL card
Router 2911 withe ios 15.
My real speed is 8Mo.
what will be the work around on this configuration.currently we have a Lease Line connection on serial interfaceISP <=SERIAL=>Router 2911<=ACCESS MODE=>Firewall(DATA DHCP SERVER located here, policy implemented here)<=TRUNK MODE=>CORE Switch(VLAN Assignment is here)<=TRUNK MODE=>ACCESS Switch(DATA and VOICE passess thru each ports)i am thinking to create a DHCP pool on the router to where my firewall should point to and from the DHCP pool it will point the internal network going to public network.
View 2 Replies View RelatedI have a Cisco 2911 that I am configuring for a remote site. I have configured a IPSec Tunnel from our main site ( ASA 5510 ). The Tunnel is up and I can connect from the main site LAN to the address of the 2911 through the IPSec Tunnel. The 2911 is equipped with a 16port switch service module. The switch is configured with an address and I can open a telnet session to the switch. From that session, I am able to reach hosts on the LAN across the IPSec tunnel. However, when I open a telnet session to the 2911 router, I cannot reach hosts on the main site LAN from that address. When I do, the traffic is sent outside of the tunnel instead of inside it. It works from the service module as traffic between the interfaces have the ACL for insteresting traffic applied, but traffic generated from the address of the 2911 router does not seem to get picked up by the ACL on the IPSec tunnel and it is getting the default route applied and going directly to the outside interface instead of to the tunnel. how to make this work?
View 3 Replies View RelatedI have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 Replies View Related