Cisco :: 2911 Router - Netflow V5 Through GRE Tunnels
Aug 12, 2012Does the 2911 router support the ability for Netflow V5 to pass through GRE tunnels? I can't seem to find any documentation that indicates this.
View 2 RepliesDoes the 2911 router support the ability for Netflow V5 to pass through GRE tunnels? I can't seem to find any documentation that indicates this.
View 2 RepliesI am trying to fetch data on netflow analyzer 9 by Cisco router 2911. But netflow is unable to show any data.
cr2911-01#sh runn | sec ip flow
ip flow-cache timeout active 1
ip flow-export version 5
ip flow-export destination 10.1.208.32 9996
[code]...
Recently bring up a new Router connected to ISP A and the Netflow collector/server is located in different location and they are connected to ISP B. I have enabled snmp and netflow config on my router(2911) but not receiving the netflow packets are not reaching the server for due to some strange reason whereas other packets like ICMP for snmp are reaching the netflow collector.Finally,I created GRE tunnel between the two locations routers and set the route for the netflow collector/server to the tunnel other end IP. In this way the netflow traffic are reaching successfully to the server.
View 1 Replies View RelatedAny major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
Is there a recommended number of GRE tunnels that Cisco 2921 ISR router with default configuration (512MB DDR2 ECC DRAM) can support?
View 5 Replies View RelatedMy current set up is 1 HQ router (2911 ISR) and 8 site offices with a non-Cisco router.Each site has an IPSEC tunnel back to the HQ router.All of the site routers have a dynamic external IP address.This set up has worked ok for now, but I would like to look at moving to GRE tunnels so traffic from the sites can be routed to each over.I have read up on the configuration and I can set up an IPSEC GRE Tunnel in test labs using a static IP address on the spokes however I have not been able to find any documentation on how to configure the HQ router to allow the tunnels from any IP address.I did try setting the tunnel destination to 0.0.0.0 on the HQ side but this does not work.
View 5 Replies View Relatedhow many GRE tunnels (without IPSEC) can 7206 router supported. I have low bandwidth 2000 links & i want to configure GRE tunnels for them.
View 1 Replies View RelatedI can set up multiple VPN tunnels on a cisco router 800 series?
View 9 Replies View RelatedI am getting the following message from a 3945 router: %CERM-4-TX_BW_LIMIT: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license.
That router has 8 Gre/IPsec tunnels and one of those tunnels is 100Mbps.The question is, could I get 100Mbps as the sum of all tunnels, or is there a restriction to 85Mbps ??
I have a client who would like to create a two VPN tunnels from one cisco 2901 router. One to the HQ and one to the DR. Is this possible?
View 4 Replies View RelatedI need to know how many IPsec VPN tunnels one Cisco1921 can support reliably. Haven't had any luck sifting through documentation on the web.
View 2 Replies View RelatedI am in the process of configuring two vpn tunnels on one interface of cisco router series 1721. Any link or document with more information?
View 5 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View RelatedHow NetFlow works when NAT is enabled in the Cisco Router? ...the translation of IP addresses is done before or after save the packets in the flow caches?
View 3 Replies View Relatedhow I configure netflow on a cisco 877 router.
I have an interface e0/4 that is 172.1.1.1 on router one (network one) which links to another router (onnetwork two) which has an interface of e0/4 172.1.1.2 which allows two networks to communicate. Network one is 192.168.0.0 /24 and network two is 10.255.255.0 /24.
How do i configure netflow to monitor the traffic going through these interfaces?
Which is the best way of creating GRE Tunnels on a GLBP enabled router? I actually have two 3845 with GLBP configured as our gateway routers, and need to create gre tunnels to branches.The plan is to use the GLBP virtual IP as the Tunnel Source address and the branch WAN interface as the tunnel Destination address, how do i handle the Tunnel IP address? Do i create the same Tunnel on both gateway routers and have a glbp virtual IP address for the Tunnel Interface as well?
View 4 Replies View RelatedI need to create multiple ip-sec vpn tunnels on A Cisco 837 ADSL Router. I am able to create one tunnel but the second connection is asking for the outside interface which is atm and already taken by the first tunnel. How can i create more tunnels?
Secondly, after creating the first tunnel i am able to access the remote lan network but when i tried tracert "remote lan ip of a pc" from my pc i got "request timed out" after passing my 837 but succeeded to reach the target. Does tracert needs something to be opened in the router?
I am currently running a 2821 to terminate vpn links from all our branch offices over a WAN. I need to add a second interface in order to facilitate a move to a different WAN provider. seeing as the 2800 models are EOL I was looking for an upgrade. My local retailer wants to sell me the following:CISCO3925E-SEC/K9 IS Router 3925E security bundle SEC license pack,HWIC-2T 2 port serial WAN card,MEM-3900-1GU2GB Upgrade to 2GB 1,now my question is why can't i use the 2900 models in order to save some money?All I need is a router that will accept 2 different incoming WANs and the ability to create vpn tunnels over them..
View 19 Replies View RelatedI have problems in exporting translations of NAT from my router through NetFlow v9 ASR1006, to my server nfdump, any opensource or licensed software (collector) that I recommend.
ip nat log translations flow-export v9 udp destination 10.1.1.15 1181
I have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
I'm thinking about changing my home router (have WAG300N now) and my big concern are GRE and ipv6ip tunnels. Righ now I experience that every few days WAG300N stops passing GRE traffic from inside of my network therefore my ipv6ip tunnel goes down. The only way to sove that is to completly reload WAG300N router.
passing ipv6ip and GRE tunnels through E4200 or EA4500? I see no passthrough in configuration option for those routers.Also performance question - I have 64Mbit symmetric internet connection. I guess both routers would easily handle that with SPI turned on and NAT?
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
I have a router cisco 3825, it is configured with netflow for monitoring traffic with WhatsUpGold, but I can't monitor this router I don't know what is the problem.Device: Router Cisco 3825 IOS: C3825-ADVENTERPRISEK9-M 12.4. [code]
I have a switch4500 12.2 and a router 2801 IOS 15.1 and this device work well with the WhatsUp but these devices have the same configuration.I see diferents ouputs when I use show ip flow export, this output is for a router that work well with WhatsUp. [code]
I have an issue with 2 site to site VPN tunnels from a RV042G router. The issue is for both VPN tunnels is that in the logs, it is showing that when the RV042G router is trying to establish the tunnel, it is getting a response from the remote gateway internal address and not the Public address of the remote gateways. On the remote gateways I have other site to site VPN's terminating fine and the tunnels are passing traffic. I only have an issue with the RV042. On the VPN Tunnel page it shows for both tunnels waiting for connection. This is an output from the log of the RV042G
Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: Peer ID is ID_IPV4_ADDR: '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: Peer ID is ID_IPV4_ADDR: '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: sending encrypted notification INVALID_ID_INFORMATION to 203.47.XXX.XX:500
VPN tunnel terminating on 203.43.XX.XXX is a Checkpoint firewall running R70 software version?VPN tunnel terminating on 203.47.XXX.XX is a Cisco ASA 5510 running ASA 8.2.4 software?As stated above, I have other VPN tunnels working fine. This RV042 is a replacement router as the original router suffered a power surge.
I need a interface v.35 on 2911 router, but it does not have WIC slot, it has EHWIC. Could some one told me if there are a card with V.35 interface that I can install in this model of router?
View 2 Replies View RelatedI have a 2911 router that I am trying to use a h.323 gateway for faxing purposes.Right now I can 4 digit dial and 10 digit the number and my analog phone answers, but when I try to place a call I get a fast busy immediately (as soon as I pick up the receiver)
View 1 Replies View RelatedI want to connect a RPS2300 to a Cisco 2911 router to provide power backup.I have two questions ,Easy one : if the 2911 PSU (internal Power Supply Unit) fails, how to confirm the RPS2300 provides power to the 2911 with no reboot of the 2911 ?,Tricky one : After we replace the broken PSU, will the 2911 reboot or not as power revert from RPS2300 to internal PSU ?
View 4 Replies View RelatedWe can't seem to SSH from the outside network into our router. Our router config looks straight forward enough.
!
! Last configuration change at 10:41:22 zone Thu Mar 15 2012 by tssconsult
! NVRAM config last updated at 11:19:12 zone Thu Mar 15 2012 by tssconsult
!
[Code].....
Recently they bought a new Cisco 2911 router and told me that they want it connected to an outside WAN connection that they hadn't used in a while so they could create a little network on the side. They want to just plug the server into the router and go. Unfortunately, I am sort of clueless about how to set up the config for it.
There are 3 GE ports, with the line from the outside coming in on GE0/0. I've already activated the interface and it is up, but that's where I get stuck.
I am connected to my internet with
WAN Interface
gig0/0 interface
ip add 62.x.x.x 255.255.255.252
duplex full
speed auto
LAN interface
gig0/1
ip add 10.x.x.x 255.255.255.0
duplex full
speed 100 ( i am keeping the speed 100 because it is connected in switch port f0/48,made the switch port as speed 100)
but after some time my connection to the internet goes off and i just shut and no shut the WAN interface and it comes back.
i have problem with a router 2900 with a card switch 16 ports (sm-es2-16p) that does not doing the intervlan routing. i have attached 2 show tech one of the router and one of the card switch 16 ports (sm-es2-16p). I connected physically the switch card to a router interface and it seem to be working because i can do a ping from my pc ( in user vlan 26) to my gateway on the router (172.20.26.1) but i can not do ping to the others vlan like (172.10.26.1) or others. .. i want to know what is happening and if it there is a way to do the trunk conectivity between the switch card and the router internally without a phyisical connection.
View 4 Replies View Relatedi am trying to upgrade the firmware in my C2960 switch to 15(1) SE2, and i get the error: Failed to execute the command archive download -sw /overwrite /http iosFile.
View 10 Replies View Related