Cisco Switching/Routing :: 3825 Router - Netflow Isn't Working With WhatsUpGold
Apr 17, 2012
I have a router cisco 3825, it is configured with netflow for monitoring traffic with WhatsUpGold, but I can't monitor this router I don't know what is the problem.Device: Router Cisco 3825 IOS: C3825-ADVENTERPRISEK9-M 12.4. [code]
I have a switch4500 12.2 and a router 2801 IOS 15.1 and this device work well with the WhatsUp but these devices have the same configuration.I see diferents ouputs when I use show ip flow export, this output is for a router that work well with WhatsUp. [code]
View 3 Replies
ADVERTISEMENT
Feb 22, 2010
I have 2*3825 routers configured with GLBP, but traffic is moving only with one router it only fallback on other router when the 1st router is isolated.
diagram: LAN=======>ASA(Routed mode with active-standby)======>one Cisco L2 switch========>2 *3825 Router
When trace route from LAN PC show that traffic is only taking via single router. LAN gateway is defined as ASA inside address and in ASA a default route pointed to GLBP address.
RTR1 config:
==========
int g0/0
ip address 1.1.1.2 255.255.255.0
glbp 1 ip 1.1.1.1
glbp 1 preemt
RTR2 config:
==========
int g0/0
ip address 1.1.1.3 255.255.255.0
glbp 1 ip 1.1.1.1
glbp 1 preemt
Is there any other config is required?
View 4 Replies
View Related
Mar 13, 2012
Any major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
View 2 Replies
View Related
Jan 22, 2013
After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on
vty0 (10.10.10.44)
Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested by bt_admin on vty0 (1
0.10.10.44). Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[code].....
View 1 Replies
View Related
Nov 10, 2011
I have problems in exporting translations of NAT from my router through NetFlow v9 ASR1006, to my server nfdump, any opensource or licensed software (collector) that I recommend.
ip nat log translations flow-export v9 udp destination 10.1.1.15 1181
View 2 Replies
View Related
May 5, 2013
I have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
View 2 Replies
View Related
Apr 10, 2013
I have a peculiar issue with a router whering I get the message in the Show Environment as below.
sh environment out
Redundant Power System is not present.
SYS PS1 is present.
Type: AC
AUX(-48V) PS1 is absent.
Fan 1 OK
Fan 2 OK
Fan 3 OK
Fan Speed Setting: Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 55
Core temperature warning: Enabled, Threshold: 70 (CPU: 95)
Board Temperature: Normal
Internal-ambient temperature = 22, Normal
CPU temperature = 37, Normal
Intake temperature = 22, Normal
Voltage 1(3300) is Normal, Current voltage = 3300 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is High/Low, Current voltage = 2168 mV
[Code]...
View 4 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Apr 9, 2012
I have a 3825 router that I have setup with the following: [code]
Its on a trunked port to my 3750 switch. I am new to this compnay and havent changed it over to IP routing on the switch quite yet.Both Vlans are setup on the 3750 without an SVI. All hosts on VLAN 1 can ping both interfaces without issue.
If I put a host on the 172 VLAN it cannot ping anything on the router. If I put another host on the VLAN they can ping each other. If I put an SVI on switch the 172 VLAN hosts can ping the switch, but still not the router. ONce I put the SVI on the switch, it can no longer ping the router. I am giving the SVI ip 172.22.1.5/24.
I have verfied with TAC that the trunk is allowing the vlans to the router.
I have been working with TAC. They have asked me to update the code on the switch, but I think they are just punting. [code]
View 23 Replies
View Related
Jul 17, 2012
I have a cisco 3825 router with two GE interfaces. GE0/0 is connected to a switch through ethernet cable. I have configured the GE0/0 interface with IP address. I have also configured static route for the local network. However, now I can only ping the GE0/0's own IP from the router. Here are the running-config:
hostname Router
!
boot-start-marker
boot-end-marker
!
!card type command needed for slot 2
enable secret 5 $1$4gxa$sykc0mcaxpCIrGc86i1ZE.
[code]...
The 10.1.52.1 is the current gateway on the 10.1.52.x LAN.
View 34 Replies
View Related
Dec 16, 2012
configure, or enable voice over ip (voip) on my router cisco 3825, I have Ip phone 7905G and 7960.
View 1 Replies
View Related
Dec 16, 2012
implement VOIP on my router 3825 I have Ip phone 7905G and 7960.
View 2 Replies
View Related
Feb 4, 2012
I have a Cisco 3825 router with a sfp module .(multi mode Cisco sfp ) connected to a Alcatel switch with fiberxon sfp. On a Cisco router the sfp card is been recognized and is seen when i used " show ip int brief " or show inventory commands. However the line protocol is down.
is their any compatibility issue with one side Cisco sfp and other side fiberxon sfp ? we have tested Cisco sfp -------Cisco sfp works fiberxon ----------------fiberxon works .
View 3 Replies
View Related
Mar 18, 2013
I have a SR520 just deployed at a remote site with Internet Access.
Working Environment:
Remote sites have SR520 with IPSEC VPN back to HQ and netflow v.5 works through the VPN back to our PRTG server.
Non-Working:
I cannot get Netflow data to our PRTG with this first SR520 implemented with Zone Base Security. I am not able to get my netflow traffic out. VPN is up and running. Internet is a dialer0 interface. I have a Kron job that does the copy run to tftp backup daily to the same PRTG server and it works fine.
Both my source interface and address on the TFTP command and the netflow commands are the same interfaces (VLAN75) and IP. The Destination ip is the same too (through the VPN tunnel).
Snipped:
flow exporter prtg
destination x.x.x.x
source Vlan75
[Code]....
View 2 Replies
View Related
Feb 11, 2012
I am trying to figure out the Flexible Net-flow on Cat 4510R+E Switch running IOS-XE code. My Neflow flow software is manageengine 7.X. I am able to see the netflow interfaces but the traffic itself is not displayed. On the Switch I can see the netflow exporter statistics counter being incremented thereby confirming as being exported.
View 2 Replies
View Related
Aug 9, 2009
Below is config on 3825. [code]
when the client get an ip from the DHCP works for same day and all of suddenly ip get released while user working and again it doesn't ip,if the same is assigned manually it works. [code]
View 1 Replies
View Related
Sep 3, 2012
I was wondering if there was a way to disable the RPS in a 3825? When I do a Sho Env All I get the following;
Redundant Power System is present.
RPS is in standby state
Redundant Power System is present.
RPS is in standby state
How ever there is no RPS in the system. At least not that I know of. There is only one power supply.
View 4 Replies
View Related
Mar 17, 2013
I have a 370 with C3KX-NM-10G module & i want to enable NetFlow on it did the specified configs
Step 1 Flexible NetFlow Flow Recordsflow record miketestmatch datalink source-vlan-idmatch datalink dot1q prioritymatch datalink mac source-addressmatch datalink mac destination-addressmatch ipv4 versionmatch ipv4 tosmatch ipv4 ttlmatch ipv4 protocolmatch ipv4 source addressmatch ipv4 destination addressmatch transport source-portmatch transport destination-portmatch interface input physical snmpcollect interface output snmpcollect counter flowscollect counter bytescollect counter packetscollect timestamp sys-uptime firstcollect timestamp sys-uptime last flow record miketestegressmatch datalink destination-vlan-id match datalink dot1q priority match datalink mac source-address match datalink mac destination-address match ipv4 version match ipv4 tos match ipv4 ttl match ipv4 protocol match ipv4 source address match ipv4 destination address match transport source-port match transport destination-port match interface output physical snmp collect interface input snmp collect counter flows collect counter bytes collect counter packets collect timestamp sys-uptime first collect timestamp sys-uptime last Step 2 Flexible NetFlow Flow ExporterFlow exporter export-to-samplicatorDestination 10.1.1.8source Vlan1Transport udp 2055option interface-table timeout 60 Step 3 Flexible NetFlow Flow Monitors# Tie the Flow Monitor to the Flow Recordflow monitor mikektestrecord miketestexporter export-to-samplicatorcache timeout active 60flow monitor mikektestegressrecord miketestegressexporter export-to-samplicatorcache timeout active 60
& Applied it to g1/1/1 but without any luck , if netflow works on the
TenGigabitEthernet1/1/1 &
TenGigabitEthernet1/1/2
Only i have four switches stacked and nothing plugged to the
C3KX-NM-10G module
View 1 Replies
View Related
Jul 23, 2012
router 7200 (12.2(33)SRE1)
two interfaces with traffic going through, placed in a Data-VRF
Another physical interface and loopback interface in the global routing-table.
ip flow ingress on all physical interfaces configured
It was running for at least a year: I was getting netflow packets on my analyzer from the box. Since a couple of weeks I get no netflow-packets anymore.debug ip flow export tells me "IPFLOW: Sending export pak to ... port 2055"
But the packet is not leaving the box. By setting up an ip sla monitor udp-echo I simulated some traffic (udp/2055) which is leaving the box.
[code]...
View 2 Replies
View Related
May 8, 2013
I have 4506 with below sup, my requirement is to enable netfolw , but as i came to know that it is not supported in this sup, is there any additional option which can be explored to get the netflow working without replacing sup.
Card Type Model
-------------------------------------------------------------+-----------------------
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
View 4 Replies
View Related
Apr 9, 2012
Ive tried to configure NetFlow on layer 2 without success. I configured the recondmonitorexporter like the configuration guide said. but still i dont receive any netflow traffic. I checked the firewall on the VM and it looks fine.
i have done the command under the ethernet interface :" layer2-switch flow monitor TEST input" - for layer2 input.
View 4 Replies
View Related
Oct 23, 2011
Net flow on the Nexus 5596upI can't seem to find any information on the Nexus 5596 support of net flow. On Nexus 5596UP support of net flow ?
View 4 Replies
View Related
Jan 17, 2012
We have one 3825 router used as voice gateway. For redudancy, we want to connect it to two different switches which has STP and HSRP running. Can I create a port-channel with two Giga interfaces in 3825 and connect to two different switches? Should I configure port channel in switch with only one port in each port-channel? I know server can be connected to different switches with NIC teaming. I just want to mimic that kind of setup. I did one time for port-channel in 3825, but it was connected to a stacked 3750X. So it's different case now.
View 2 Replies
View Related
Dec 11, 2012
I just ran into an interesting issue. VG Cisco 3825 crashes regularly with the following message in a crashinfo.
%ALIGN-1-FATAL: Illegal access to a low address 16:26:07 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
%ALIGN-1-FATAL: Illegal access to a low address 16:26:08 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
16:26:08 CET Tue Dec 11 2012: TLB (store) exception, CPU signal 10, PC = 0x603F32F8
Router: Cisco 3825
IOS: c3825-spservicesk9-mz.151-3.T3.bin
View 1 Replies
View Related
Nov 12, 2009
If a Supervisor 6-E will support NetFlow on a Catalyst 4507R-E?If not, what are my options for NetFlow on a 4507R-E?
View 7 Replies
View Related
Nov 3, 2011
To enable netflow export on ASR1001, do i need the firewall feaure license or not ?Docs are not really clear, NBAR requires FW license, but i am unsure about Netflow?
View 1 Replies
View Related
Feb 6, 2012
I am trying to use the following commands on the switch but it is not supported:
ip route-cache flow
ip flow-export destination
Attached is the output for show version and show module commands from the switch.
View 9 Replies
View Related
Jun 4, 2012
It is possible to configure the IOS NetFlow 122-58.SE2 in a Catalyst 3560?
View 5 Replies
View Related
Dec 25, 2011
I need to know if Cisco Switch 2960 support Netflow. If it doesn't, how do I configure the switch to enable Netflow?
View 3 Replies
View Related
Oct 30, 2011
I have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies
View Related
Jun 4, 2013
We have Cisco Catalyst 6509-V-E VSS Switch with Sup2T und IOS Version 15.0(1)SY2. We are gettin input netflow information from the gi2/3/7 but not output ... I am not sure why it does not work.
View 1 Replies
View Related
May 22, 2012
How to get a summary of netflow statistics on NX-OS? On IOS you could do sh ip cache flow which would show what I need? Can't find a similar command on the Nexus Platform.
View 4 Replies
View Related
