Cisco Switching/Routing :: 3825 Wacky Routing With VLAN
Apr 9, 2012
I have a 3825 router that I have setup with the following: [code]
Its on a trunked port to my 3750 switch. I am new to this compnay and havent changed it over to IP routing on the switch quite yet.Both Vlans are setup on the 3750 without an SVI. All hosts on VLAN 1 can ping both interfaces without issue.
If I put a host on the 172 VLAN it cannot ping anything on the router. If I put another host on the VLAN they can ping each other. If I put an SVI on switch the 172 VLAN hosts can ping the switch, but still not the router. ONce I put the SVI on the switch, it can no longer ping the router. I am giving the SVI ip 172.22.1.5/24.
I have verfied with TAC that the trunk is allowing the vlans to the router.
I have been working with TAC. They have asked me to update the code on the switch, but I think they are just punting. [code]
View 23 Replies
ADVERTISEMENT
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Jul 17, 2012
I have a cisco 3825 router with two GE interfaces. GE0/0 is connected to a switch through ethernet cable. I have configured the GE0/0 interface with IP address. I have also configured static route for the local network. However, now I can only ping the GE0/0's own IP from the router. Here are the running-config:
hostname Router
!
boot-start-marker
boot-end-marker
!
!card type command needed for slot 2
enable secret 5 $1$4gxa$sykc0mcaxpCIrGc86i1ZE.
[code]...
The 10.1.52.1 is the current gateway on the 10.1.52.x LAN.
View 34 Replies
View Related
Dec 16, 2012
configure, or enable voice over ip (voip) on my router cisco 3825, I have Ip phone 7905G and 7960.
View 1 Replies
View Related
Jan 22, 2013
After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on
vty0 (10.10.10.44)
Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested by bt_admin on vty0 (1
0.10.10.44). Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[code].....
View 1 Replies
View Related
Dec 16, 2012
implement VOIP on my router 3825 I have Ip phone 7905G and 7960.
View 2 Replies
View Related
Feb 4, 2012
I have a Cisco 3825 router with a sfp module .(multi mode Cisco sfp ) connected to a Alcatel switch with fiberxon sfp. On a Cisco router the sfp card is been recognized and is seen when i used " show ip int brief " or show inventory commands. However the line protocol is down.
is their any compatibility issue with one side Cisco sfp and other side fiberxon sfp ? we have tested Cisco sfp -------Cisco sfp works fiberxon ----------------fiberxon works .
View 3 Replies
View Related
Feb 22, 2010
I have 2*3825 routers configured with GLBP, but traffic is moving only with one router it only fallback on other router when the 1st router is isolated.
diagram: LAN=======>ASA(Routed mode with active-standby)======>one Cisco L2 switch========>2 *3825 Router
When trace route from LAN PC show that traffic is only taking via single router. LAN gateway is defined as ASA inside address and in ASA a default route pointed to GLBP address.
RTR1 config:
==========
int g0/0
ip address 1.1.1.2 255.255.255.0
glbp 1 ip 1.1.1.1
glbp 1 preemt
RTR2 config:
==========
int g0/0
ip address 1.1.1.3 255.255.255.0
glbp 1 ip 1.1.1.1
glbp 1 preemt
Is there any other config is required?
View 4 Replies
View Related
Aug 9, 2009
Below is config on 3825. [code]
when the client get an ip from the DHCP works for same day and all of suddenly ip get released while user working and again it doesn't ip,if the same is assigned manually it works. [code]
View 1 Replies
View Related
Sep 3, 2012
I was wondering if there was a way to disable the RPS in a 3825? When I do a Sho Env All I get the following;
Redundant Power System is present.
RPS is in standby state
Redundant Power System is present.
RPS is in standby state
How ever there is no RPS in the system. At least not that I know of. There is only one power supply.
View 4 Replies
View Related
Jan 17, 2012
We have one 3825 router used as voice gateway. For redudancy, we want to connect it to two different switches which has STP and HSRP running. Can I create a port-channel with two Giga interfaces in 3825 and connect to two different switches? Should I configure port channel in switch with only one port in each port-channel? I know server can be connected to different switches with NIC teaming. I just want to mimic that kind of setup. I did one time for port-channel in 3825, but it was connected to a stacked 3750X. So it's different case now.
View 2 Replies
View Related
Dec 11, 2012
I just ran into an interesting issue. VG Cisco 3825 crashes regularly with the following message in a crashinfo.
%ALIGN-1-FATAL: Illegal access to a low address 16:26:07 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
%ALIGN-1-FATAL: Illegal access to a low address 16:26:08 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
16:26:08 CET Tue Dec 11 2012: TLB (store) exception, CPU signal 10, PC = 0x603F32F8
Router: Cisco 3825
IOS: c3825-spservicesk9-mz.151-3.T3.bin
View 1 Replies
View Related
Apr 17, 2012
I have a router cisco 3825, it is configured with netflow for monitoring traffic with WhatsUpGold, but I can't monitor this router I don't know what is the problem.Device: Router Cisco 3825 IOS: C3825-ADVENTERPRISEK9-M 12.4. [code]
I have a switch4500 12.2 and a router 2801 IOS 15.1 and this device work well with the WhatsUp but these devices have the same configuration.I see diferents ouputs when I use show ip flow export, this output is for a router that work well with WhatsUp. [code]
View 3 Replies
View Related
Apr 16, 2013
I thought I saw a post/question in regards to "how to" configure a Broadband backup for a MPLS circuit.. What I am trying to do is use a cable/dsl/ broadband (secondary) connection as a backup to a MPLS circuit (primary). I have EIGRP and BGP configured on both the branch endpoint and the tunnel headend. The tunnel is used by the interface that connects to the secondary circuit. The branch location router is a 1841 and the "headend" tunnel router is a 3825. I am wondering about the configuration/syntax of a "weight" or static route that can be used to have data flow over the tunnel when the MPLS circuit goes down - and then switch back to the MPLS circuit when it comes back on line.
View 1 Replies
View Related
Apr 10, 2013
I have a peculiar issue with a router whering I get the message in the Show Environment as below.
sh environment out
Redundant Power System is not present.
SYS PS1 is present.
Type: AC
AUX(-48V) PS1 is absent.
Fan 1 OK
Fan 2 OK
Fan 3 OK
Fan Speed Setting: Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 55
Core temperature warning: Enabled, Threshold: 70 (CPU: 95)
Board Temperature: Normal
Internal-ambient temperature = 22, Normal
CPU temperature = 37, Normal
Intake temperature = 22, Normal
Voltage 1(3300) is Normal, Current voltage = 3300 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is High/Low, Current voltage = 2168 mV
[Code]...
View 4 Replies
View Related
Nov 27, 2012
We are using 3825 Cisco router with IOS version 12.4(24)T2. The unknown protocol drops on our GigabitEthernet0/1 interface is increasing. This interface is connected to our modem. What could be causing this unknown protocol drops?
cnshaccent-gw-2#sh int GigabitEthernet0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is ffff.ffff.ffff (bia ffff.ffff.ffff)
[Code]....
View 1 Replies
View Related
Dec 11, 2006
I have reconfigure my Cisco 3825 for ssh after we lost the config sue to a power faliure. I have reconfigure the same way it was configured before and working properly.
when I try to access the router using Putty ssh, I get to the authentication screen but after entering uername and password (enable secrete and line password the same) i get access denied.
Below is the ssh and line configuration on the router. I have seen the pdf that has been recommended here at Netpro and have followed that document but still having problem:
[code]...
View 16 Replies
View Related
Apr 24, 2008
Our ISP hands us an ethernet link. ISP router has one address of (for argument sake) 1.1.1.0/30 net, - let's say they have 1.1.1.1 we have the other usable address of 1.1.1.2/30 assigned to our 3825 router. Is it possible to use hsrp or vrrp if there is not two valid/unique "wan" IPs to assign to our routers? For example, if we had a pair of 3825 routers? are we stuck with basically a manual failover or requesting our isp to provide a larger address wan block?
View 2 Replies
View Related
Feb 16, 2012
Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies
View Related
Oct 24, 2012
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies
View Related
Oct 28, 2012
I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies
View Related
Jul 24, 2007
Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies
View Related
Jun 1, 2013
I have a DC topology based on 2 layers, access and aggregation, based on 2 pairs of N5548Ps, both without L3 Daugher Cards. My intent is to use the aggregation N5K pair as L3 inter VLAN layer, so I configured all the VLAN default GWs there. The 2 layers are interconnected via vPC, in a double-sided vPC topology for some N2Ks and some vSwitches. The point is that, despite connecitivity is working fairly ok, for some applications, like file transfer via either FTP or HTTP, between hosts in different VLANs, the performance is too poor. The file transfer starts ok, but after a while it becomes lower and lower. ICMP is working, but I can see some strange random behaviour, like having some packets taking more that 20 ms (sometimes 40 or more), whilst average is 2 ms.
I read through some articles saying that until you don´t have the L3 license (the one coming with L3 Daughter Cards) you can expect some weird behaviour on L3 level. Is that true?. What can I do apart of purchasing L3 Daughter Cards?. Can I enable L3 Basic license at the moment (I don´t need dynamic routing for now).
Here some excerpts of what I´m saying:
PING results:
10000 packets transmitted, 10000 packets received, 0.00% packet loss
round-trip min/avg/max = 0.809/2.496/57.559 ms
System version: 5.0(3)N2(1)
License and features on the N5Ks:
switch# sho license usage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
FCOE_NPV_PKG No - Unused -
FM_SERVER_PKG No - Unused -
ENTERPRISE_PKG No - Unused -
[code]....
View 3 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Feb 15, 2013
We have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
View 20 Replies
View Related
Jan 10, 2012
Can nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
Feb 5, 2012
I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
View 11 Replies
View Related
Mar 28, 2013
I am working for a large campus network. The network has more than 70 VLANS in a Layer 3 Switch(Catalyst 4503). Customer wants to stop intervlan routing between all vlans except 2 vlans. How will i do that? I have also a Firewall (ASA 5520) & a Router (2811) in up of the switch. Besides this, I have run HSRP in Layer 3 Switches for redundancy.how will i stop intervlan routing between VLANS except 2, with ACL or any other process has?
View 10 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Feb 26, 2013
We got a layer3 switched network, with one vlan for every switch, routed by a cat4006. [code] So can we put some ports on different switches in, let`s say vlan 50, with different ips? For example, Port 0/3 on Switch 1 and 0/8 on Switch 2, but keeping the ip of the "old" vlan? Or is it necessary to configure a specified vlan interface with ip-adress for every vlan if i want to route it?
View 4 Replies
View Related
Jul 24, 2012
Since two weeks I have a problem with the VLANs who I started to configure. I hope together we find the way.I have 5 VLANS configured in a CISCO 3560G switch. In my windows server 2003 I configured DHCP scope for each VLAN.One of the requirement to connect vlans each other is to put the IP of each vlan as gateway in the clients.So, how can I do to access to internet?. The ip of my Firewall are in one of the VLAN´s.When the configuration of the LAN only had one DHCP scope the gateway was the ip of my firewall. But now i don´t know how to configure the DHCP server, or the firewall, or the switch, or all of them To get access to internet.
View 2 Replies
View Related
Apr 28, 2012
We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies
View Related
