Cisco Switching/Routing :: 3825 - Access Denied While Entering Username And Password
Dec 11, 2006
I have reconfigure my Cisco 3825 for ssh after we lost the config sue to a power faliure. I have reconfigure the same way it was configured before and working properly.
when I try to access the router using Putty ssh, I get to the authentication screen but after entering uername and password (enable secrete and line password the same) i get access denied.
Below is the ssh and line configuration on the router. I have seen the pdf that has been recommended here at Netpro and have followed that document but still having problem:
[code]...
View 16 Replies
ADVERTISEMENT
Jun 24, 2011
How i can get access lan computer drives with out entering login password
View 1 Replies
View Related
Jun 26, 2012
I did not know the username and password for my DI-524 so I wanted to do a reset...used a paper clip and held the reset button for ten seconds, unplugged it, powered it up, and as per online instructions tried to type in 192.168.0.1 to access the username and password field so that I could enter "admin" and blank password. Here's where my lack of knowledge comes in. I am working off a MacBook with no Ethernet connection, just wifi. Is what I am trying to do even possible? Or does the computer I configure the router with have to be hardwired to the Internet while I do it?
View 1 Replies
View Related
Jul 4, 2012
I have Cisco ME3400 series switch .Unable to login as i have no user name and password. I want to set the swirch to factory default but not found any nub to press.
View 2 Replies
View Related
Nov 24, 2012
I want to configure " Username & Password" on Cisco 3750 switch. I need to configure as "username xxxxxx privilege 15 password 5 xxxxxxx "
Is it possible to create password with level 5 ? I want to know about level 5 "password" & level 7 "password" ?
when i tried I am not able to configure with " password 5"
View 12 Replies
View Related
Sep 24, 2012
Is there anyway to pull the usernames and passwords from a switch via SNMP or write a new username and password to switch via SNMP. I have switch that was apparently misconfigured and i am not feeling like driving all the way down there to console in.
View 2 Replies
View Related
Jun 17, 2012
In a new Cisco 3750, if the username and password is not configured seperately, what will be the default username & password. I have only configured enable password. when we access it remotely via telnet it prompts for username/password.
View 3 Replies
View Related
May 19, 2013
i am having cisco 881 router i want to know whether i can configure dialer interface with username and password for my dsl internet connection.
View 2 Replies
View Related
Jan 20, 2009
how do i recover username and password for 870 series router
View 5 Replies
View Related
Dec 11, 2012
I just ran into an interesting issue. VG Cisco 3825 crashes regularly with the following message in a crashinfo.
%ALIGN-1-FATAL: Illegal access to a low address 16:26:07 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
%ALIGN-1-FATAL: Illegal access to a low address 16:26:08 CET Tue Dec 11 2012
addr=0x0, pc=0x603EFF38z , ra=0xFFFFCC41z , sp=0x702E3C28
16:26:08 CET Tue Dec 11 2012: TLB (store) exception, CPU signal 10, PC = 0x603F32F8
Router: Cisco 3825
IOS: c3825-spservicesk9-mz.151-3.T3.bin
View 1 Replies
View Related
Jun 20, 2011
How can i edit on who will have the most percentage of internet?i cant access the username and password.
View 1 Replies
View Related
Nov 14, 2012
I am unable to set a password and/or username for guest access.
View 1 Replies
View Related
Aug 3, 2009
I cannot access the Username and password on my WAG160N - the ones I thought were correct do not accepted, nor are the quoted 'defaults'.I have tried holding down 'reset' for 30 secs; I have tried powercycling the router after and during this; I have tried 'resetting' with the phone and ethernet connections unplugged. This is NOT returning the machine to the default settings - and neither is it 'wiping' the existing settings for my ISP.The amusing thing is - it works perfectly well, but I can't alter my security settings and I can't alter other settings if I change my ISP (as I was intending to do).
View 9 Replies
View Related
Jan 3, 2013
I am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
View 2 Replies
View Related
Jun 25, 2010
Recently I have purchased two brand new wap4410n access points.
I have connected my computer directly to one of the access points, and attempted to connect to the Web Configuration utility through my web browser.
I'm using a: 09' MacBook Pro, running Snow Leopard and Safari 5.
I can access the login screen of the access point, although when I enter the default username: admin and password admin, the login screen returns an error: Invalid username and/or password (or something to that effect). The URL changes to: http://192.168.1.245/login.htm&no=3.
I have reset the device by holding in the reset button for thirty seconds, powered down, powered up and re-attempted to login.
I still get the same error as above.
I have attempted to access the Web Configuration utility on both access points, and both access points provide the same error. I have also tried using the username: cisco and password: cisco.
Cisco, when contacted, said both access points must be faulty and I should replace them.
The probability of such an occurrence happening with two devices seems very low, and leads me to think there must be other factors at play. The only constant I can think of is the fact I'm using the same computer to access the devices.
View 4 Replies
View Related
Aug 26, 2012
I am looking to get access to an external hard drive that I have set up on my wireless network.When I try to do an automated Windows backup (off my Vista based laptop files) on to an external hard drive which is connected to my wireless network (through a Belkin router) I am being asked for a user name and password to access the connected hard drive on the network. The thing is that I don't remember setting up a username and password for the hard drive at all. I can paste single files mannually onto the external hard drive without being asked for a username and password. I did perform an automated Windows backup off my other Windows 7 laptop and was not ask for a username and password. where to find the username and password information ?
View 3 Replies
View Related
Jan 14, 2013
When i try to enter the password for my N300 Belkin Router into my wifi connection setup in my computer it will not accept any letters, only numbers.
View 1 Replies
View Related
Jul 15, 2011
I have tried to connect my Kindle to my E3000 without success. The Kindle shows that the router is there but after entering my password in the Kindle it will not connect. I tried going into Cisco Connect and enable "Guest" user. Again the Kindle shows that the router is there showing "Guest User" and after entering the password for the guest user it still will not connect. The Kindle does connect to the internet through a router that is shown - I have no idea whose router it is - but at least it proves that the Kindel will connect to the internet.
View 2 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Apr 9, 2012
I have a 3825 router that I have setup with the following: [code]
Its on a trunked port to my 3750 switch. I am new to this compnay and havent changed it over to IP routing on the switch quite yet.Both Vlans are setup on the 3750 without an SVI. All hosts on VLAN 1 can ping both interfaces without issue.
If I put a host on the 172 VLAN it cannot ping anything on the router. If I put another host on the VLAN they can ping each other. If I put an SVI on switch the 172 VLAN hosts can ping the switch, but still not the router. ONce I put the SVI on the switch, it can no longer ping the router. I am giving the SVI ip 172.22.1.5/24.
I have verfied with TAC that the trunk is allowing the vlans to the router.
I have been working with TAC. They have asked me to update the code on the switch, but I think they are just punting. [code]
View 23 Replies
View Related
Jul 17, 2012
I have a cisco 3825 router with two GE interfaces. GE0/0 is connected to a switch through ethernet cable. I have configured the GE0/0 interface with IP address. I have also configured static route for the local network. However, now I can only ping the GE0/0's own IP from the router. Here are the running-config:
hostname Router
!
boot-start-marker
boot-end-marker
!
!card type command needed for slot 2
enable secret 5 $1$4gxa$sykc0mcaxpCIrGc86i1ZE.
[code]...
The 10.1.52.1 is the current gateway on the 10.1.52.x LAN.
View 34 Replies
View Related
Dec 16, 2012
configure, or enable voice over ip (voip) on my router cisco 3825, I have Ip phone 7905G and 7960.
View 1 Replies
View Related
Jan 22, 2013
After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on
vty0 (10.10.10.44)
Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested by bt_admin on vty0 (1
0.10.10.44). Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[code].....
View 1 Replies
View Related
Dec 16, 2012
implement VOIP on my router 3825 I have Ip phone 7905G and 7960.
View 2 Replies
View Related
Feb 4, 2012
I have a Cisco 3825 router with a sfp module .(multi mode Cisco sfp ) connected to a Alcatel switch with fiberxon sfp. On a Cisco router the sfp card is been recognized and is seen when i used " show ip int brief " or show inventory commands. However the line protocol is down.
is their any compatibility issue with one side Cisco sfp and other side fiberxon sfp ? we have tested Cisco sfp -------Cisco sfp works fiberxon ----------------fiberxon works .
View 3 Replies
View Related
Feb 22, 2010
I have 2*3825 routers configured with GLBP, but traffic is moving only with one router it only fallback on other router when the 1st router is isolated.
diagram: LAN=======>ASA(Routed mode with active-standby)======>one Cisco L2 switch========>2 *3825 Router
When trace route from LAN PC show that traffic is only taking via single router. LAN gateway is defined as ASA inside address and in ASA a default route pointed to GLBP address.
RTR1 config:
==========
int g0/0
ip address 1.1.1.2 255.255.255.0
glbp 1 ip 1.1.1.1
glbp 1 preemt
RTR2 config:
==========
int g0/0
ip address 1.1.1.3 255.255.255.0
glbp 1 ip 1.1.1.1
glbp 1 preemt
Is there any other config is required?
View 4 Replies
View Related
Aug 9, 2009
Below is config on 3825. [code]
when the client get an ip from the DHCP works for same day and all of suddenly ip get released while user working and again it doesn't ip,if the same is assigned manually it works. [code]
View 1 Replies
View Related
Sep 3, 2012
I was wondering if there was a way to disable the RPS in a 3825? When I do a Sho Env All I get the following;
Redundant Power System is present.
RPS is in standby state
Redundant Power System is present.
RPS is in standby state
How ever there is no RPS in the system. At least not that I know of. There is only one power supply.
View 4 Replies
View Related
Oct 5, 2011
My network topology consists of 3 directly connected routers where the central router contains sensitive data and i need to block traffic from ENTERING the LAN adjoined to that router. My issue is creating an access list to DENY traffic from entering the network connected to Fa0/1 but ALLOW traffic to exit from that network. I am using one class C network which is subnetted 7 times to provide me with the required LAN's.
View 2 Replies
View Related
Nov 5, 2012
Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q
[Code].....
View 3 Replies
View Related
Jan 17, 2012
We have one 3825 router used as voice gateway. For redudancy, we want to connect it to two different switches which has STP and HSRP running. Can I create a port-channel with two Giga interfaces in 3825 and connect to two different switches? Should I configure port channel in switch with only one port in each port-channel? I know server can be connected to different switches with NIC teaming. I just want to mimic that kind of setup. I did one time for port-channel in 3825, but it was connected to a stacked 3750X. So it's different case now.
View 2 Replies
View Related
Apr 17, 2012
I have a router cisco 3825, it is configured with netflow for monitoring traffic with WhatsUpGold, but I can't monitor this router I don't know what is the problem.Device: Router Cisco 3825 IOS: C3825-ADVENTERPRISEK9-M 12.4. [code]
I have a switch4500 12.2 and a router 2801 IOS 15.1 and this device work well with the WhatsUp but these devices have the same configuration.I see diferents ouputs when I use show ip flow export, this output is for a router that work well with WhatsUp. [code]
View 3 Replies
View Related
Apr 16, 2013
I thought I saw a post/question in regards to "how to" configure a Broadband backup for a MPLS circuit.. What I am trying to do is use a cable/dsl/ broadband (secondary) connection as a backup to a MPLS circuit (primary). I have EIGRP and BGP configured on both the branch endpoint and the tunnel headend. The tunnel is used by the interface that connects to the secondary circuit. The branch location router is a 1841 and the "headend" tunnel router is a 3825. I am wondering about the configuration/syntax of a "weight" or static route that can be used to have data flow over the tunnel when the MPLS circuit goes down - and then switch back to the MPLS circuit when it comes back on line.
View 1 Replies
View Related
