Cisco Switching/Routing :: 3825 Router - Redundant Power System Is Not Present
Apr 10, 2013
I have a peculiar issue with a router whering I get the message in the Show Environment as below.
sh environment out
Redundant Power System is not present.
SYS PS1 is present.
Type: AC
AUX(-48V) PS1 is absent.
Fan 1 OK
Fan 2 OK
Fan 3 OK
Fan Speed Setting: Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 55
Core temperature warning: Enabled, Threshold: 70 (CPU: 95)
Board Temperature: Normal
Internal-ambient temperature = 22, Normal
CPU temperature = 37, Normal
Intake temperature = 22, Normal
Voltage 1(3300) is Normal, Current voltage = 3300 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is High/Low, Current voltage = 2168 mV
[Code]...
View 4 Replies
ADVERTISEMENT
Sep 3, 2012
I was wondering if there was a way to disable the RPS in a 3825? When I do a Sho Env All I get the following;
Redundant Power System is present.
RPS is in standby state
Redundant Power System is present.
RPS is in standby state
How ever there is no RPS in the system. At least not that I know of. There is only one power supply.
View 4 Replies
View Related
May 10, 2012
Does a portable RPS device either from Cisco or another manufacturer exists, that would allow you to move primary power for a switch without causing an outage? I realize that for the Catalyst 3560 for example, you can get an RPS 2300 or 675, but my understanding is that these are made for a more permanent installation, not to mention rather costly.
It looks like the RPS 675 is rather inexpensive after all, especially in the secondary market, but still rather large for toting around.
View 1 Replies
View Related
Oct 2, 2012
I know that the 6500 with a Sup 720 reserves power for a redundant 720. If there is no plan to install that redundant Sup, is there a means of releasing that reserved power? I know that one approach would be to insert a card into that slot to cut the reserve down, but I need to reclaim all of that power.
View 10 Replies
View Related
Dec 23, 2012
I was wondering if I am able to add a redundant power supply to an asr 1001 router that is in production without losing connectivity or causing any diruption to the Users - is it hotswappable?
View 1 Replies
View Related
Aug 1, 2012
I have a problem with a catalyst 3508G XL ...
The problem is as follows:
When I power on the system LED keeps blinking and does nothing.I've tried connecting the cable to the console port, but can not communicate.
View 1 Replies
View Related
Nov 21, 2011
I hav e a 3750X Cisco Switch (WS-C3750X-48T-S) It is two Ethernet base SFP installed and working fine at slot 1 & 2, Now i am trying to install GLC-SX-MM in 3rd and 4th slot, but its not coming up, showing not present?
Gi1/1/1 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/2 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/3 notconnect 1000 auto auto Not Present
Gi1/1/4 notconnect 1 auto auto Not Present
image i am using is
C3750E-UNIVERSALK9-M
View 6 Replies
View Related
Dec 6, 2012
I am receiving this error after connecting a copper adapter on a GBIC blade in a 6509. Here are the results from the show Interface. I am waiting to confirm the device on the other side settings but as far as I see I get UP and Up for protocol and line respectively.
GigabitEthernet2/11 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0009.11e4.f3ce (bia 0009.11e4.f3ce)
Description: RCPBSDEV
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]....
View 3 Replies
View Related
Jan 22, 2013
After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on
vty0 (10.10.10.44)
Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested by bt_admin on vty0 (1
0.10.10.44). Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[code].....
View 1 Replies
View Related
Apr 17, 2012
I have a router cisco 3825, it is configured with netflow for monitoring traffic with WhatsUpGold, but I can't monitor this router I don't know what is the problem.Device: Router Cisco 3825 IOS: C3825-ADVENTERPRISEK9-M 12.4. [code]
I have a switch4500 12.2 and a router 2801 IOS 15.1 and this device work well with the WhatsUp but these devices have the same configuration.I see diferents ouputs when I use show ip flow export, this output is for a router that work well with WhatsUp. [code]
View 3 Replies
View Related
Aug 29, 2012
I have a router cisco 3825, It is being restarted autometically. and gives a message "System returned to ROM by bus error at PC 0x6125DCFC, address 0x15A3C78B" in show ver.
View 5 Replies
View Related
Sep 21, 2012
We have 3750-X's with dual power supplies. When one of them is disconnected the NMS/Netcool is not picking up the trap. What MIB is needed to monitor the power supplies?
View 1 Replies
View Related
Feb 10, 2010
I have a 6509-E with redundant 3000W power supplies (WS-CAC-3000W) but one supply is current non-operational.From the outputs I'm not sure whether the issue is (more likely to be) with the supply to the PSU or the PSU itself, i.e. whether my first action should be to get an electrian to check the supply or fault call the PSU with our maintenance providers and have it replaced?
View 3 Replies
View Related
Jun 1, 2013
Does SG500X support the following
redundant Power Supply?PIM sparse mode (PIM-SM), PIM dense mode (PIM-DM), and PIM sparse-dense mode?Layer 4 prioritization: enables prioritization based on TCP/UDP port numbersUni-Directional Link Detection (UDLD) — monitors a link between two switches and blocks the ports on both ends of the link if the link goes down at any point between the two devices
View 2 Replies
View Related
Jun 9, 2013
I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
View 1 Replies
View Related
Sep 4, 2012
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
View 5 Replies
View Related
Apr 14, 2013
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
View 1 Replies
View Related
Feb 28, 2011
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
View 3 Replies
View Related
Apr 4, 2012
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies
View Related
Aug 18, 2011
Is it possible for me to plug in and turn on on-board redundant power supply for a 4402 WLC that is already online and in production without any disruption to Wireless users and APs attached to that same controller?
View 1 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Apr 9, 2012
I have a 3825 router that I have setup with the following: [code]
Its on a trunked port to my 3750 switch. I am new to this compnay and havent changed it over to IP routing on the switch quite yet.Both Vlans are setup on the 3750 without an SVI. All hosts on VLAN 1 can ping both interfaces without issue.
If I put a host on the 172 VLAN it cannot ping anything on the router. If I put another host on the VLAN they can ping each other. If I put an SVI on switch the 172 VLAN hosts can ping the switch, but still not the router. ONce I put the SVI on the switch, it can no longer ping the router. I am giving the SVI ip 172.22.1.5/24.
I have verfied with TAC that the trunk is allowing the vlans to the router.
I have been working with TAC. They have asked me to update the code on the switch, but I think they are just punting. [code]
View 23 Replies
View Related
Oct 29, 2011
How to replace a defective redundant sup. I read on several articles that inserting new redundant sup should not be an issue as the active sup will always send its configuation to the standby. We are running SSO on the Sup720. Should I switch it to RPR before I install the redundant sup? I read a case wherein they switched it to RPR from SSO before inserting the new redundant sup. My concern is the IOS mismatch since Cisco doesn't always send the same IOS on RMAs.What I am planning is this.
1. Save/Backup configuration
2. Remove the redundant sup on slot 8 (since it is a 6513)
3. Insert the new redundant sup on slot 8.
4. Check if all the configurations were synced from slot 7 to slot 8.
5. Copy the IOS from sup-bootflash to slavesup-bootflash. (if the IOS are not the same)
6. Check show bootvar to see if the boot variables are correct.
7. If bootvar is the same, reload slot 8 to boot the new IOS.
Is this a good plan or am I missing something? I am worried with this document if the redundant sup has a different software. If i insert the card in slot8, according to Cisco, it will revert to RPR. If slot 8 boots and it has a different OS, then slot 7 will switch to RPR even if it's active. Would I still be able to access the slavesup-bootflash of slot 8? Is it going to boot 100%? I read that doing a force switchover will cause a flip and RPR would cause the line cards to reinitialize and I don't want that. Well I am not going to do a force switchover since i want slot7 to be active and retain slot 8 as hot.
View 3 Replies
View Related
Jul 17, 2012
I have a cisco 3825 router with two GE interfaces. GE0/0 is connected to a switch through ethernet cable. I have configured the GE0/0 interface with IP address. I have also configured static route for the local network. However, now I can only ping the GE0/0's own IP from the router. Here are the running-config:
hostname Router
!
boot-start-marker
boot-end-marker
!
!card type command needed for slot 2
enable secret 5 $1$4gxa$sykc0mcaxpCIrGc86i1ZE.
[code]...
The 10.1.52.1 is the current gateway on the 10.1.52.x LAN.
View 34 Replies
View Related
Feb 10, 2012
I would like to add a redundant supervisor to my core 6509. Is this tricky to do? I know they have to be running the same IOS. I am worried if I put the new supervisor in it will write over the exsisting running config.
Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2
Policy Feature Card 2 WS-F6K-PFC2
Cat6k MSFC 2 daughterboard WS-F6K-MSFC2
View 4 Replies
View Related
Aug 30, 2012
Can 2 Cisco 4507E switches with redundant SUP6-E modules be connected togther using the the standard 10GB CX4 modules and CX4 copper cables? Are there any special modules or cables required.
View 1 Replies
View Related
May 8, 2012
I sort of messed up and upgraded the IOS on one supervisor on a 6500 without doing the second, saved and reloaded. How to I get the 2nd one working again? When I issued a show module the "normal" Active sup shows active and the standby shows as Supervisor.
View 5 Replies
View Related
Feb 5, 2013
we have 2 Supervisor IV modules in our 4507, i want to upgrade the IOS as its still on 12.2 and i am going to upgrade it to the latest.
my first question is, if i update the IOS on the bootflash will it replicate to the secondarybootflash?
secondly, can i force a reboot of the secondary supervisor, then the primary after the secondary is up? i'm just trying to minimise downtime and get a plan going.
is there a difference in 12 vs 15 that would impact my current config that i should be aware of?
View 2 Replies
View Related
Nov 7, 2011
I have an 4507R with one Supervisor Engin V card. I want to add a redundant supervisor engin card to my 4507R Chassis.
Can i use supervisor engin 6-E for redundant or i must use Supervisor Engin V ?
Witch model of Supervisor Engines Supported with this chasis?
View 2 Replies
View Related
Sep 25, 2012
How to set up redundant LAN Ring topology with load balancing for a cisco catalyst 3560 platform.
View 10 Replies
View Related
Dec 16, 2012
configure, or enable voice over ip (voip) on my router cisco 3825, I have Ip phone 7905G and 7960.
View 1 Replies
View Related
Dec 16, 2012
implement VOIP on my router 3825 I have Ip phone 7905G and 7960.
View 2 Replies
View Related
