Cisco Switching/Routing :: 3560 - Redundant Lan With Load Balancing
Sep 25, 2012How to set up redundant LAN Ring topology with load balancing for a cisco catalyst 3560 platform.
View 10 Replies
ADVERTISEMENT
Cisco WAN :: CEF - Per Packet Load Balancing (3560)?
Jul 5, 2011confirm is Per packet load balancing is supported in the 3560's ?
I am going around in circles, and can't find a definate Y or N answer.
I have a suspicion this CEF feature is only available on routers.
Cisco WAN :: 3560 - Switch Not Communicating With Load Balancing Router
Nov 18, 2011I have a Cisco network on a ship where I work, I have an Ericsson GSM Access point which picks up local GSM 3G signal and broadcasts it onboard. I have two of these units and they are connected to a D-Link Load balancing router which is in turn connected to a Cisco 3560 Series 8 poe switch. Each unit is on a different subnet. The Cisco is on the DHCP server from my AD server (Windows 2003 Server) The Load balancing router has no DHCP and the Ericsson units have their own DHCP servers.On the Cisco switch if I plug in with a laptop I get an IP address for the DHCP on my server. I cannot ping the load balancing router from it. If I connect to the Load balancing router and set a static address for that subnet I can access the internet via the Ericsson units. And if I connect to the Ericsson I can access the Internet.
View 22 Replies View RelatedCisco Switching/Routing :: Nexus 7K Is Not Load Balancing
Aug 5, 2012We have Nexus 7K on production. 7K chasis is not load balancing with non-cisco devices with etherchannel or LACP..I have tried all load balancing algorithms but in vain. [code]
View 3 Replies View RelatedCisco Switching/Routing :: 881-K9 Load Balancing And Static NAT
Dec 3, 2012i'm going to configure a 881-k9 with:
- Ethernet 0/0 LAN (Private Address)
- Ethernet 0/1 ISP1 (Public Address 1)
- Ethernet 0/2 ISP2 (Public Address 2)
find some configuration example to:
- have load balancing over the two ISP connection, used to connect to Internet
- configure Static NAT to bind:
- TCP 443
- TCP 1723on ISP1 e ISP2 Interface to a LAN Address (SBS2008 Server)
Cisco Switching/Routing :: 7609 Portchannel Load-Balancing
Oct 23, 2012I'm trying to make MGSCP solution. I have Cisco 7609 with following configuration:
Mod Ports Card Type Model
--- ----- -------------------------------------- ------------------
3 8 CEF720 8 port 10GE with DFC WS-X6708-10GE
5 5 Route Switch Processor 720 10GE (Activ RSP720-3CXL-10GE
7 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
8 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
9 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX.
Cisco Switching/Routing :: Nexus 7K Load Balancing On LACP
Jul 26, 2012I have conneccted a server with LACP on Nexus extender. I am starting different file copy from diffferent sources to this server, it does not load balance.
source addresse: 192.168.30.3 / 192.168.30.1
destination: 192.168.30.2
Cisco Switching/Routing :: 4900M Etherchannel Load Balancing
Dec 18, 2012We have to cisco WS-C4900M with Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).We have four gigabit link connected between those two switches.We have create a LACP port channel with those four ports on both switches. Ether-channel is up and running and defined with a load-balancing method of src-dst-ip.But when we test the load-balancing, it's not using the src-dst-ip rule with the XOR: [code]
View 5 Replies View RelatedCisco Switching/Routing :: Possible Load Balancing On 2821 Router?
Apr 15, 2012I have a 2821 Router, with a VWIC2-2MFT card in it, with two T1s going into that card. The two T1s are a bundled MPLS line.
I then have a cable modem connection going into the gigabit Ethernet GE 0/1 port on the router.
Right now, the cable modem provides a backup connection in case the T1s go down.
What I was wondering is if there was a way to 'combine' the bandwidth from the two T1s with the cable modem?
Cisco Switching/Routing :: 3560 - Portable Redundant Power System For Catalyst Switches?
May 10, 2012Does a portable RPS device either from Cisco or another manufacturer exists, that would allow you to move primary power for a switch without causing an outage? I realize that for the Catalyst 3560 for example, you can get an RPS 2300 or 675, but my understanding is that these are made for a more permanent installation, not to mention rather costly.
It looks like the RPS 675 is rather inexpensive after all, especially in the secondary market, but still rather large for toting around.
Cisco Switching/Routing :: CSS 11501 - Configuring CSS Content / Load Balancing
Feb 3, 2012I would like configure a CSS content, that uses the sorry service principal in an advanced way.
I am familiar with the primary Sorry Server command and see that the CSS would send all connections to the named service that is configured as the primary Sorry Server.
What I would like to do is to configure the CSS, so that once it’s decided it’s in a “sorry” state (all the services that are configured with “add service” are down) that it load balances to a different set of services.
To explain what I’ve been trying to do in the form of configuration on the CSS, I’ve pasted some pretend config below.
Connections come into IP address 1.1.1.1, which normally get load balanced between 9.1.1.1, 9.1.1.2 and 9.1.1.3.
If 9.1.1.1, 9.1.1.2 and 9.1.1.3 are all down, the sorry service is used and the CSS starts passing traffic to 1.1.2.1, which I want it to load balance between 9.1.2.1, 9.1.2.2 and 9.1.2.3.
The order that I have applied the config, is different to the below, as I set out to configure in this order: secondary services, secondary content, sorry service, primary services, primary content.
The order of the config below is different, because I wanted it in the order that the traffic flows and the CSS won’t take the config in that order!
The wall I have ran into, is that when I try to create the service I have named “Sorry Service”, I get the following error:
%% Service IP Address conflicts with a local I/F, VIP, mg mt route.
[Code] .....
Cisco Switching/Routing :: Nexus 5548UP Switches - Load Balancing?
Mar 10, 2013The best option for load balancing between 2 X Cisco nexus 5548UP switches located at one site and connecting to 2 X Cisco nexus 5548UP switches located at another site.
The sites are connected via a 1GB fibre connection. I am unable to use GLBP until GLBP is supported in further software releases.
Cisco Switching/Routing :: Static Load Balancing On 3650-X IP Base?
Nov 22, 2011Does 3650-X IP Base support Static Load Balancing or i should upgrade to ip service SW ?
View 4 Replies View RelatedCisco Switching/Routing :: 4500X EtherChannel Symmetric Load Balancing
May 8, 2013I have probem with symmetric load balancig, in case when both ends of ether channel are on the sam switch (we are using VLAN translation).We need to create L2 port channel with both ends on same switch (Cisco WS-C4500X-24X-ES), for example:Po1 – Gi0/1, Gi0/3 (one end of port channel )Po2 – Gi0/2, Gi0/4 (other end of port channel)On ports in Po2 we will configure VLAN mapping.My question is what is the best ether-channel load-balancing scheme with wich we can accomplish full symmetry in both directions? For example, if traffic in one direction goes through Gi0/1 (member of Po1), in other direction also must go through Gi0/1. This is required because we need to connect four appliances for DPI (they are full L2 transparent) and traffic through each appliance need to be symmetric.
I can set-up src-ip, dst-ip, src-dst-ip etc. load balancing, but, actually I need src-ip on Po1 and dst-ip on Po2. Is there any way to set up different load balancing mechanism for different ether channel on same switch (4500X).
Cisco Switching/Routing :: 6500 Will Load-balancing Work As Intended
Sep 27, 2012If the load balancing is set to src-dst-ip, will a layer 2 switch forward based on that information? Particularly talking about a 6500, with trunk interfaces, since those packets never go to the layer 3 engine, will the load-balancing work as intended?
View 2 Replies View RelatedCisco Switching/Routing :: C2960 - Port Channel Load Balancing?
Apr 15, 2013I have an inquiry about a configuration I deploy in a C2960 switch. I have configured a ether channel with 8 ports, the load balanced method is source mac address. The bundling protocol is LACP.
I have found the ether channel is not balanced as I expect. One of the eight interfaces is congested.
Code...
Cisco Switching/Routing :: 6509 / Default Route Load Balancing?
Nov 29, 2012Right now I have 2 default routes load balancing 100MB internet links. This is on my 2 6509's.
ip route 0.0.0.0 0.0.0.0 10.47.2.1 (FWSM)
ip route 0.0.0.0 0.0.0.0 10.47.2.250 (5510)
Is there anyway to make the first default route take more of the traffic, like 60/40 or 70/30?Any program that I could use to see top users going through the FWSM?
Cisco Switching/Routing :: 1921 Load Balancing Over 3 ADSL Lines
Aug 22, 2012I have the requirement to provide a Cisco Router with 3 x ADSL lines (768k) to increase the internet speed.PPP multilink is not supported from the ISP.
Is it possbile to distribute the traffic between this three ADSL lines?How can I configure this?
I have the following hardware configuration:
1 x CISCO1921-SEC/K9
2 x EHWIC-VA-DSL-B
The third ADSL line is connected over an ADSL modem at one fixed Router Gigabit interface.
Cisco Switching/Routing :: 1941 Auto Failover With Load Balancing?
Jan 27, 2013One of our customer has 3 ISP Line, out of which Two are Broadband and One is Leased Line. All 3 ISP interfaces are Etherent.
Now, they want Auto Failover with Load balancing among these 3 ISP lines.
Can we do same implementation in Cisco 1941 Router?? What licenses required in router for same?
Cisco Switching/Routing :: 6509 - Load Balancing Nexus Switches
Jan 24, 2013I am trying to understand what load balancing method is used on a port channel on a Nexus switch . I have a server connected by a VPC to two Nexus switches. The nexus switches are only acting as layer 2 switches. I have a 6509 connected via a upstream link that does all of the routing for my VLANS. If have a server connected to the Nexus switches and it talks to a server on my 6509 what load balancing happens on the Nexus going across VPC 27 which is a layer 2 trunk going up to my 6509. Is it done on layer 2 or layer 3 flows?
My Nexus shows the default load balancing configurations
Port Channel Load-Balancing Configuration:System: source-dest-ip
Port Channel Load-Balancing Addresses Used Per-Protocol:Non-IP: source-dest-macIP: source-dest-ip source-dest-mac
Cisco Switching/Routing :: 6509 - Etherchannel Load Balancing Between Two Switches
Mar 5, 2012Is it possible to use two different load balancing methods at each end of a port-channel between two switches?
We have a Cisco 6509 at one end of the port-channel and a Cisco blade switch 3020 at the other end. Right now, we are using "src-dst-ip" at both end of the port-channel. We would like to change this. That is, we would like the #3020 switch to use "src-dst-ip" while the 6509 switch should use the "src-dst-port".
Why we want to do this, the reason is that we have FWSMs on the 6509. I've read that by configuring "src-dst-port" on the 6509, one can get a better performance of traffic going through the FWSM. However, the issue is that the 3020 switch does not support "src-dst-port".
Cisco Switching/Routing :: Asa 5520 Load Balancing Based Upon Http Or Https
Mar 5, 2012I have a customer who wants his new ASA-5520 to load balance out-going traffic between 2 ISPs, fairly normal request. Now here's the twist. He wants to separate traffic based upon the protocol used, http to one ISP, https to the other.
View 3 Replies View RelatedCisco Switching/Routing :: 3750X Port Channel Load Balancing Protocols
Jan 15, 2012What I am attempting to achieve is to aggregate trunk ports out of a VMware server into a single logical connection to give as much bandwidth as possible, the switches are 3750X and are three stacked together with the server connections spread across the stack. What I am not sure about is if two port channel load balance protocols can happy co-exist on the switch, by default the switch is using MAC address load balancing and Vmware wants to use IP Source load balancing. As other trunks and channels exist on the switch I don't want to make a change that will affect the other live connections if changing this is a global setting and not local on the channel.
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 2248 / Port-Channels On N2K Not Load Balancing?
Sep 5, 2012I have a dual-homed fabric (Nexus 2248 dual attached to two Nexus 5020's via vPC). On this Nexus 2248 is a server that has a four port LACP etherchannel. The ports do not appear to be load balancing correctly. The output below shows the four ports in use and it clearly shows port e138/1/10 as getting the most use. When I use the "show port-channel load-balance forwarding-path..." command on either of the vPC switches for various source and destination IP's that use this link, it shows them correctly load-balancing across the four ports. But we do not see this when looking at stats on both the server side and the switch side.
dc5020-3g# sh int e138/1/10,e138/1/12,e138/1/14,e138/1/16 | i seconds
30 seconds input rate 552 bits/sec, 69 bytes/sec, 0 packets/sec
30 seconds output rate 130120 bits/sec, 16265 bytes/sec, 161 packets/sec
Load-Interval #2: 5 minute (300 seconds)
30 seconds input rate 40 bits/sec, 5 bytes/sec, 0 packets/sec
[code]....
**************** Config info below. This is a vPC pair and the port configs are identical on both switches so I'm only showing the configs for one switch to keep it simple.
dc5020-3g# sh port-channel load-balance
Port Channel Load-Balancing Configuration:
System: source-dest-ip
Port Channel Load-Balancing Addresses Used Per-Protocol:
Non-IP: source-dest-mac
IP: source-dest-ip source-dest-mac
[code]....
Cisco Switching/Routing :: 4500E - Changing Default Etherchannel Load Balancing Algorithm
Mar 25, 2012Will there be some pause in traffic on formed ether channel interfaces (4500E switch), when i will change the default ether channel load balancing method to src-dst-port (or any other non-default method)?
View 1 Replies View RelatedCisco Switching/Routing :: Created Load Balancing Between Two Catalyst 3550 On Couple Of Vlans
Feb 24, 2012I am testing on lab equipment (2 Catalyst 3550 and 1 Catalyst 3560) HSRP version 1 and 2.I successfully created a load balancing between the two Catalyst 3550 on a couple of vlans (11 and 12) on ver 1
now, just adding the command "standby xx version 2" my hosts on the 2 vlans are completely unable to ping the virtual IP def. gw on debugging i checked that msgs are exchangedthe two cat 3550 are seeing each other on HSRP (active / standby roles)the real ip addresses are pingable rebooted the swiches (just as a last resort try)deleted arp chache on hostsremoved the auth on hsrp all of this no effect.
i also tried to modify the priority on the cat 3560 (before he was on both vlans in standby) to make it the active one and with the same config it worked flawlessly.
My only idea is that there is a bug on CATs 3550 (IOS: c3550-ipservicesk9-mz.122-55.SE4.bin) [code]
Cisco Switching/Routing :: 3560 - OSPF Load Sharing Design
Sep 16, 2012We have our network setup as displayed in the attached. We have 2 HQ offices and 1 branch office. The branch office needs to connect to resources located at both HQs but taking the most effecient path. We have ethernet circuits connecting from each HQ to 2 x Cisco 3560 switches in the branch. HSRP has been configured on the 3560 switches with SW1 as active and SW2 as standby. OSFP has been configured in a single area 0 and the path cost on the link between HQs has been increase to allow 3560 SW1 to route to HQ1 directly and HQ2 via 3560 SW2.The 3560s are connected with a trunk with a L3 SVI for OSPF. This seems to work ok but I have noticed that the branch could become transit if the HQ1 to HQ2 link breaks. How can this be avoided? I realise that if we configure the branch subnets and SW1 to SW2 link in a stub area (area1) then all traffic will route from SW1 to HQ1 and will never share over SW2. I'm assuming that this is because OSPF chooses inter-area routes over intra-area.
View 4 Replies View RelatedCisco WAN :: ASR1001 / L2 Over L3 With Load-balancing?
Nov 30, 2011i'm trying to accomplish the following:I want to trasport a bunch of vlan layer 2 etherchannel on a pair of layer3 connections, using L3 to load balance.i was considering a pair of options:
1) bridging + gre (non applicable since i cant bridge 2 interface beloging to a etherchannel to a tunnel)
2) L2TP is it possible to accomplish this with the above tecnology? any reference, configuration example?
3) AoMLPS is it possible to accomplish this with the above tecnology ? any reference, configuration example?
I cant modify topology, the routers used are ASR1001 It is mandatory that both sites have a layer2 connection between them.
Cisco WAN :: 2811 DSL Load Balancing
Dec 9, 2010I have a Cisco 2811 router with two HWIC-ADSL cards configured for dsl connection. I have two lines from the same ISP and i am load balancing between them. I have created a couple of SLA's to check the state of the connections and add to the routing table the two default routes if both are up or any one of them is up.My problem is that when i try to download big files (especially antivirus updates) the download at some point stops (especially the antivirus exits with an error of unreachability). If i shut down one line everything works fine.Could i use something (configuration-wise) to prevent this problem from happening?????Is there any way i can combine the two lines? They are simple ADSL connctions with static ip's.
View 8 Replies View RelatedCisco WAN :: Load Balancing On ASR1002?
Jun 25, 2012One of our customer just purchased ASR1002 router, they have three internet links from different ISPs and they dont have any remote site, they have three different public IP pool as their respective ISPs. So, is it possible to load balance the internet traffic using all three link on Cisco ASR router ( IOS - Advance Enterprise Services)
View 3 Replies View RelatedCisco WAN :: 4506-E DSL Load Balancing
Jun 10, 2012I need to configure DSL Load Balancing on Core Cisco Switch 4506-E. I have a Router Cisco 2811 with 2GE Ports and a Firewall Cisco ASA5505. I have 8 Physical DSL Connections with 1Mb each. I need to combine that 8 Mb on Core Switch and allow each end user to access the Internet via the available DSL connection which means that every user has 8 Mb available.
View 7 Replies View RelatedCisco VPN :: Load Balancing ASA 5520
Sep 13, 2011We have an ASA5520 pair that we will be installing to load balance SSLVPN connections. Below is a portion of our configs pertaining to the VPN load-balancing feature (configured on both ASAs):My specific question is related to routing of return traffic to load-balanced VPN sessions. Is there some kind of persistence function that tells the return traffic which ASA to route back to? For instance, if ASA1 has a VPN connection having IP address 10.211.112.1 associated to it, and ASA2 has a VPN connection having IP address 10.211.112.100, how does the return traffic for each connection know which ASA to route back to?
View 1 Replies View RelatedCisco VPN :: Load Balancing ASA 5510
Sep 13, 2011Currently we have deployed site to site vpn between 2 asa 5510 model. one is corporate site and one is remote site. now we plan to use radware load balancer in which 2 isp will terminate. now if at a remote site wecreate only 1 ipsec tunnel and mention sigle isp peering. if one isp fails at corporate how remote site will be access by site to site vpn through 2 isp vpn. what thing we need to do over asa as well as load balancer at both end.
View 6 Replies View Related