I have a router cisco 3825, It is being restarted autometically. and gives a message "System returned to ROM by bus error at PC 0x6125DCFC, address 0x15A3C78B" in show ver.
View 5 RepliesI have an 3845 router:Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)After an unexpected reboot it says: System returned to ROM by bus error at PC 0x6323F398, address 0xB0D0B39 at 12:35:09 GMT Fri Jan 27 2012..To troubleshoot this error I need to find out what kind of processor this router has. It doesnt fall in either of the categories descibed in url...
View 4 Replies View RelatedI have problem with the WAN Router 7206. It has been reloaded automatically 2 times since yesterday. [code] I have already put this message to the output interpreter and the solution is upgrading to the latest IOS. But, when I search in the Bug Toolkit about SegV problem, this bug status is still "Open". So, how can I upgrade to the latest IOS if the status of this bug is still open?
View 2 Replies View RelatedWhen i was changing the class-maps i get lost the router. I have attached the crash log file, am i hitting a bug here? I have many times modified the class-maps on the go without any issues.
View 4 Replies View RelatedI noticed that my router 7200 was reboot for a bus error. The error occurred while the system was operational. After the restart the router works properly for more than 6 days.
This is the sh ver:
Cisco IOS Software, 7200 Software (C7200P-IPBASEK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 22:57 by prod_rel_team
[code].....
Seems that the error "System returned to ROM by bus error at PC 0x2E0BF30, address 0x0" should be a special type of bus error crash is when the crash is caused by a corrupted program counter (PC). The PC value is the location of the instruction which the processor was executing when the bus error occured. In this case, the PC has jumped to the address 0x0 (probably because of a null pointer), but this is not where the instruction is located.
Can I consider this as a processor memory parity errors and wait for a second parity error before I replace anything?
My switch is getting restarted and the error shown is : System returned to ROM by error - Debug Exception (Could be NULL pointer dereference)
View 4 Replies View RelatedWhenever I want to turn off the ip cache flow and enter command "no ip flow egress" on a router interface, the router will self reboot and returned with the error message - System returned to ROM by bus error at PC message in the show version ouput.
I tried on two different routers below here and both also undergoing a cold restart when I key in the command "no ip flow egress" on the said interface
1) Cisco 7206 running IOS 12.4(1c)
interface GigabitEthernet0/1
ip address 10.20.10.2 255.255.255.0
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/1 and the router self restarted and return the message Router uptime is 3 minutes System returned to ROM by bus error at PC 0x606D48FC,address 0x0
2) Cisco 3845 running IOS 12.4(3e)
interface GigabitEthernet0/0
ip address 10.20.20.2 255.255.255.0
ip nbar protocol-discovery
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/0 and the router self restarted and return the message
Router uptime is 3 minutes System returned to ROM by bus error at PC 0x6007EBE0, address 0x0
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
We have observed that one of the 3560 switch was rebooted with "System returned to ROM by address error at PC 0x0, address 0x0"
View 1 Replies View Relatedwhat does this log message mean? (RV120W fw 1.0.3.10)
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:18:46 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:18:46 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:13:36 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
[code]....
I got this error this operation returned because the timeout period expired error code 0x000005b4
View 1 Replies View RelatedI have a peculiar issue with a router whering I get the message in the Show Environment as below.
sh environment out
Redundant Power System is not present.
SYS PS1 is present.
Type: AC
AUX(-48V) PS1 is absent.
Fan 1 OK
Fan 2 OK
Fan 3 OK
Fan Speed Setting: Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 55
Core temperature warning: Enabled, Threshold: 70 (CPU: 95)
Board Temperature: Normal
Internal-ambient temperature = 22, Normal
CPU temperature = 37, Normal
Intake temperature = 22, Normal
Voltage 1(3300) is Normal, Current voltage = 3300 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is High/Low, Current voltage = 2168 mV
[Code]...
After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on
vty0 (10.10.10.44)
Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested by bt_admin on vty0 (1
0.10.10.44). Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[code].....
We find ourselves in a difficult situation with the Cisco VPN Client version 5.0.07.0290 where it keeps giving us an
"Error 42: Unable to create certificate enrollment request"
When we attempt to use the Online enrollment method to create and enroll a new certificate. There is no additional information in the VPN client logs where we have set 3-High for all logs. In addition, Wire shark does not show any packets sent from the machine running the client to the Cisco 3825 router which runs the Cisco CA.
To create and enroll a certificate we do the following:
1. Click on the Enroll button to show the Certificate Enrollment dialog
2. Select Online
3. Select <New> for Certificate Authority
4. Enter http://192.168.120.1 as CA URL (note, 192.168.120.1 is the IP of the Cisco 3825)
5. Click Next to display the dialog where we can enter certificate details
6. Enter details in all fields except IP Address and Domain
7. Click Enroll which shows a dialog with the Error 42 ... message in it.
If we attempt to create a request by using the File method, all works fine, that is, the client creates a file with the enrollment request. The fact that the client does not send any messages to the Cisco CA leads us to believe that we have a problem on the client machine. However, the client does not write any information in the logs, so it is a bit hard to fix the problem. I can provide additional configuration information if required for both the client and the Cisco CA. Note that we have not modified any client configuration. Basically, we installed the client on a Windows 7 64bit machine and attempted the steps listed above.
i have a problem with the playstation 3 system when i sign in it takes a while todo that all of a sudden a error appeared on my screen saying "An error occured (80023121)" and me and my dad try to fix the problem but nothing seems to be working
View 1 Replies View RelatedCisco VG224 (R527x) processor (revision 4.1) with 119808K/11264K bytes of memory. Processor board ID FGL150411MN, R527x CPU at 225MHz, Implementation 40, Rev 3.1, 1 On-Board Twenty-Four FXS Analog Voice Module V2.1, 2 FastEthernet interfaces, DRAM configuration is 64 bits wide with parity disabled. 63K bytes of non-volatile configuration memory. System fpga version is 250027, % Crashinfo may not be recovered at flash:crashinfo, % This file system device reports an error.
View 4 Replies View RelatedJust upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 5 Replies View RelatedIve tried to reinstall XP, to redownload driver, to reinstall driver etc...
View 9 Replies View RelatedTrying to install WMP54G v4.0 on XP SP3. I have tried all three PCI slots. Removing driver RT2500.SYS system will boot. Put it back and BSOD Error:driver_irql_not_less_or_equal
View 8 Replies View RelatedI'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
I have Dell Inspiron 15 3520 laptop bought in December 2012 with Windows 8 Pro. It was working fine until two days ago. I am unable to obtain DHCP lease either through wireless or wired network. After troubleshooting, I found DHCP service is not running and try to restart but of no avail.I ran sfc /scannow and the results are OK.
View 2 Replies View RelatedRecently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies View RelatedI have received emails in my inbox to say that emails i have sent have been returned but they are in chinese and I haven't sent them.
View 2 Replies View RelatedI have a new Win 7 Dell Precision Workstation that will not log in to my domain. I get an error that there is no login server available if I attempt to log in using a domain account. I log in as the local admin and then try to join a domain using the Join a Domain or Workgroup wizard. I then get an error stating "this operation returned because the timeout period expired". I have had to reset my core switch to get a couple of the new boxes (including this one) to even join the domain. I also show no internet in the Network and Sharing Center most of the time.
View 2 Replies View RelatedThe process is IP Input and I'm not really sure how to troubleshoot it. I've read through all the doc's on high cpu load if I shutdown the port that feeds that network, CPU drops to around 30%, bring it back up and it jumps up to 90%+. I've got a policy map on the interface shaping the traffic
[code]...
I am trying to upgrade the IOS on cisco 3825 from 124-9.T1.bin to 124.24.t6.bin, after I upload the configuration to the CF and verify the file, everything appears fine but when I try to load the new image it fails with following error and falls back to old image :-
System Bootstrap, version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
Readonly ROMMON intializedboot: cannot open "flash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "c3825-advsecurityk9-mz.124-24.T6.bin"
Then after few minutes it boot to the Old 12(4).9 ios again.
What are the prerequisites before doing this? I have to upgrade a router this Wednesday evening if there is an opportunity to move it to a code that is more current that the one the client is currently running which is 12.4(25b). I see on the Cisco Support site that after this code, everything moves to 15.
View 5 Replies View RelatedI have a 3825 with a 16 port etherswitch card installed that I'm trying to setup rate-limits on. Interface G0/0 is the connection to the outside world and int g0/1 has a couple of 2950 switches attached to it.
The etherswitch card, f1/0, f1,1 etc has corresponding vlans, 902, 903 etc each with an IP 10.110.1.x, 10.110.2.x and all part of access-group 111. The switches connect on sub-interfaces g0/1.101, g0/1.102 etc and have IP's 10.55.1.x, 10.55.2.x and part of access-group 101.
What i'm trying to achieve is that every port / IP that is on access-group 111 shares 3Mb of bandwidth in/out and access-group 101 shares a separate 3Mb of bandwidth in/out.
I've created two access-lists as follows;
access-list 101 permit ip 10.55.0.0 0.0.255.255 any
access-list 111 permit ip 10.110.0.0 0.0.255.255 any
And on int g0/0 I've created the following rate-limits;
rate-limit input access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit input access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
Now instead of both access-groups having 3Mb each they all seem to be sharing 3Mb! I've tried class-maps and policy-maps but to no avail..
LAN subnet conflicts with WAN subnet. My router is d-link 825 and my cable modem is Cisco EPC-3825. Op system is W7. Everything worked great with an older cable modem (Cisco 3000).
View 4 Replies View RelatedI want to know the number of routes supported by CISCO3825-HSEC/K9(512MB DRAM).
View 2 Replies View RelatedIs there any way to configure 3825 to ensure that all packets have a source IP address that matches the correct source interface (similar to ASA's 'ip verify reverse-path interface')? Currently, we manage anti spoofing with a bunch of ACLs, however I'm looking for a more manageable solution.
View 2 Replies View RelatedI want to configure PAT on the router I have no configuration yet
View 1 Replies View RelatedWe need to upgrade the RAM on our 3825 Cisco Router. Currently, it's 512MB and we want to upgrade it to 1GB. So do I just order another 512MB DRAM Memory? What is the part number that I need to order?
Here is the show ver:
Cisco IOS Software, 3800 Software (C3825-ADVENTERPRISEK9-M), Version 12.4(24)T2, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 19-Oct-09 21:05 by prod_rel_team(code)