Linksys Wireless Adapters :: XP Bluescreens With RT2500 System Error
Dec 28, 2007Ive tried to reinstall XP, to redownload driver, to reinstall driver etc...
View 9 Replies
ADVERTISEMENT
Linksys Wireless Adapters :: WMP54G RT2500 System Driver Causes BSOD Error?
Oct 27, 2008Trying to install WMP54G v4.0 on XP SP3. I have tried all three PCI slots. Removing driver RT2500.SYS system will boot. Put it back and BSOD Error:driver_irql_not_less_or_equal
View 8 Replies View RelatedLinksys Wireless Adapters :: WMP300N Install On New System Without CD?
May 28, 2011How do i install the WMP300N without the installation CD ? I bought a new PC and i cant find the CD?
View 7 Replies View RelatedLinksys Wireless Adapters :: AE1000 Disconnects From System?
Feb 11, 2011I recently purchased two of these units. One used with a quad core AMD rig and another with a single core AMD rig. Both systems are running Windows 7 but the older single core system is having issues. I noticed that I keep hearing the sound of a USB device being disconnected but wasnt sure what it was until I noticed when I try to copy large files over wireless the AE1000 disconnects from my system like I've unplugged it. I've swapped the two units and it didn't solve the problem. My newer quad core doesn't experience the issue at all. I've also tried different USB ports but that doesn't solve the issue either.
View 9 Replies View RelatedLinksys Wireless Adapters :: WMP54Gv4 Causes System Crash With Airport Extreme
Jan 4, 2010I had been using my Linksys wireless-G PCI adapter WMP54Gv4 in a PC running XP (SP3) and an Airport Extreme wireless router for the past 4 or 5 years without any issues. Then recently, my wireless signal had become flaky on all client machines (on both PC and various Macs, which reported weak signal and kept dropping and searching for a new PPPoE from my DSL line). AT&T verified our line was fine and even sent a new modem but troubles persisted, so I bought a new Airport Extreme last week. This solved the network reliability issue on the Macs just fine.
However, the PC with the WMP54Gv4 adapter now crashes whenever the new Airport Extreme is turned on. There have been no hardware or software changes on the PC, yet it now reliably produces a BSOD stating "DRIVER_IRQL_NOT_LESS_OR_EQUAL". This crash also happens when booting in safe mode with networking. I can avoid the system crash when booting in safe mode without networking or booting normally without my Airport Extreme turned on, though I do see this error: "Linksys Wireless Network Monitor: Access violation at address 0040756D in module EMP54Gv4.exe"
So I cannot run any tests of the PCI card on the machine when the wireless network is on, since the operating system crashes.
The evidence thus points to an explanation where my wireless network from the new Airport Extreme is tripping up the operation of the linksys wireless card in a way that XP hates. I know the wireless network is OK, since it works fine on my Macs. I confirmed that my driver (v3.0.3.0) is still listed as current for this PCI card, so it's not a matter of having an out-of-date driver.
Here's another observation that may be relevant: When I first started using the new Airport Extreme with WPA2 protection, the PC could run without crashing, but it could not connect to the wireless network. I also had trouble connecting via my Macs. Then I switched the Airport Extreme to use WPA/WPA2 security, which is when the network-based PC crashing ensued (though the Macs can now connect just fine).
Linksys Wireless Adapters :: WPC54GS Not Recognized By System (HP Pavilion Dv6137eu)
Jun 14, 2011We bought an Wireless-G Notebook Adapter with SpeedBooster (WPC54GS: [URL] for an laptop ( HP Pavilion dv6137eu : [URL] for my sister. at the specifications of the laptop, it tells me (translated): Pc card slots: 1 ExpressCard/54 slot (also supporting ExpressCard/34) first question: is that slot the right one, fitting the cisco wpc54gs?
if we bought the right thing, whats wrong then? : The problem is, she installed everything like how its told in steps 1a-g of: steps [URL] then she plugged in restarted like the next step told. even after a new restart, the laptop seems to not recognise the card. even the power light isn't light up. Is the power light only light up when its also installed and recogised by the computer? or does it have to light up from the moment its connected to the slot? we couldn't also find it at the device manager:
the network adapters we found are, i think, the build in ones. at what folder at the hardware tree had the card in de bus has to appear? i dont know what the only device thats not recognised here, must be, but we cant install it with the cdrom of the cisco card, so i dont thing it is the cisco card?
Linksys Wireless Adapters :: Wpc11ver.3 / Get Driver For Ubuntu Operating System?
Dec 22, 2012wpc11ver.3 / get driver for Ubuntu operating system?
View 2 Replies View RelatedLinksys Wireless Adapters :: WMP600N - System FW Not Include Enough Info To Properly Configure / Use This Device
May 4, 2010I've purchased a wmp600n pci adapter january this year and installed it with no problems and did not encoutner a single problem with it until today. I use windows 7 64bit.
I've just came back from a 3 week absence and turned on my computer for the first time since i left. I notice that I have no wireless connection. So i go to network connections and realize that my wireless adapter dosent even show up..only my lan card. So i check my device manager, and under network adapters, i can see my wireless adapter, but with an exclamation mark next to it. I check the properties, and under the status box, it gives me this message.Your computer's system firmware does not include enough information to properly configure and use this device. To use this device, contact your computer manufacturer to obtain a firmware or BIOS update. (Code 35).
So i do what it says, and flash my bios to the latest version. After the update, I check the device manager, and the error message is still there. I check my wireless adapter driver version and it is v3.0.2, which is the latest version according to the linksys driver download webpage. I've tried uninstalling and re-installing the adapter but no luck there. I also checked to see if maybe there was a problem with my pci slot and that was not the problem because I was able to use my older wireless adapter.
Linksys Wireless Adapters :: Error 211 On A WUSB100v2 (Win7 X64)
Aug 7, 2011I have during the day attemped to install the card on my machine.
At first attempt, I followed the instruction on the CD. It took forever, and ended up giving me the notorious "Error 211".
I then tried the different solutions. First this one: [URL] The difference however being that the card indeed was found and identified properly by the device manager. Installed the downloaded drivers manually, but if I remember correctly (this was a few hours ago) it timed out and I got a message the device wasn't properly installed.
[URL] Here I couldn't even perform the first step, since I couldn't even remove the drivers! The process of uninstalling drivers gets stuck, and I waited for over an hour, and eventually decided to just rip the USB dongle out. That stopped the uninstalling process. Refitted the USB dongle in the computer, and the network device showed up the same way as it did before.
So, what apperas to be the case is that the device seems to have the proper drivers installed, but for some reason it cannot communicate properly with the computer. I can see it in the device manager; I can see the properties and even change the settings. However, I cannot uninstall it, remove it (with the Remove USB Device dialogue) or access it in any other way - it becomes completely unresponsive and if anything happens, it times out. The card does not show up in the list of avaliable network devices. The blue diode on the dongle lights, and sometimes flashes as if it was working.
System spec:
Case: ANTEC HTPC FUSION M-ATX
Mobo: ASUS MAXIMUS III GENE P55 S-1156 M-ATXRAM: CORSAIR 8GB DDR3 XMS3 INTEL I5/I7 PC10666 1333MHZProcessor: INTEL CORE I5 750 2.66GHZ 8MB S-1156OS: MICROSOFT WINDOWS 7 HOME PREM 64-BIT ENG
HDD: 2x WESTERN DIGITAL CAVIAR BLACK 500GB 7200RPM SATA/300
Graphics: XFX GEFORCE GTX 275 LITE 896MB GDDR3 PCI-E
Linksys Wireless Adapters :: WET11 Give Error 404 On 192.168.1.225
Aug 23, 2012my Linksys Ethernet bridge WET11 V1.0, where working perfect, but when i reset the device, and try lo login whit user admin and password admin, my browser show error 404, this happ whit crome, mozilla, an I Explorer, i download the Setup wizard, and the error message is "the setup wizard was unable to locate a wirless ethernet bridge on the network......"
when i connect the cable to de device, the lan led is on, and the ping command give me reply.
another port to configure, such as telnet?
Linksys Wireless Adapters :: WRT 110/ WPC 100 - No Connection Error Message
Dec 31, 2008I purchased a WRT110 wireless router several weeks ago. Used it with my WPC55AG with no problems at all. I liked the wireless-N, so I decided to upgrade to a wireless-N notebook card and purchased a WPC100. I can always connect to the router with 100% signal strength. However, when trying to access the Internet, sometimes I can connect to websites, but I regularly get an error message that Internet Explorer cannot connect to the internet, even though the signal strength is still 100%.
Tried going back to my WPC55AG and do not get any connection error messages. Tried connecting to my router with my PSP and do not get any connection error messages. Connected to another wireless router that didn't have WPA or WEP using my WPC100 and didn't get any connection error messages..
Linksys Wireless Adapters :: WUSB600N May Not Be Installed Properly - Error 211
Mar 17, 2011I am using the USB network adaptor, Model : WUSB600N version 2. It has worked fine whenever I have needed it. Except now. I received “Your adapter may not be installed properly”” ERROR 211: The network adapter is not installed properly” message last night. Also the Windows pop-up message: “USB device not recognized” message. I removed the adaptor and reinstalled it into another USB port. The same thing happened. I moved it again to a third USB port, I received the same error on all five of my PC’s USB ports. I was not able to access the network at all last night.
I brought in laptop into work today , because the antenna/extension is kept there. I inserted the adaptor and it started right up. After an hour of usage, I disconnected the antenna and the adaptor and reinserting the adaptor without the antenna directly into the USB port. And it still worked fine.I turned the PC off, disconnected everything and went to lunch. When I returned, booted up the PC, and inserted the adaptor and, once again got the error message: “ERROR 211 – The network adapter is not installed properly…. I tried again, this time using the antenna, and it is up and working for now.
Linksys Wireless Adapters :: Wusb100 Installation Error 211 On Windows 7
Jan 9, 2012I am having trouble installing the wusb100 adapter on a Windows 7 Pro 64 bit machine. I have downloaded the updated files and when I go to install the software, I get to the section that says, "plug in the adapter." At that point, it says it can see the adapter and it sits for 3 minutes trying to complete the install. The I get error 211 which says the adapter is plugged in wrong and to try again. I notice that the adapter is set up with drivers in the Hardward Management area of Windows, however, I cannot access the adapter to set it up. Thoughts? I have also tried to manually install the drivers but they are installed. The trouble is I can't see the adapter.
View 2 Replies View RelatedAcer Travelmate2350 - Getting A Message No Supported Wireless Adapters Available In The System?
Oct 17, 2011i have acer travelmate2350. i want to use internet in my laptop by wireless but i am getting a message "no supported wireless adapters available in the system" on the icon of wireless (red cross is also showing).
View 1 Replies View RelatedPS3 System - Error Has Occurred (80023121)?
Apr 28, 2011i have a problem with the playstation 3 system when i sign in it takes a while todo that all of a sudden a error appeared on my screen saying "An error occured (80023121)" and me and my dad try to fix the problem but nothing seems to be working
View 1 Replies View RelatedCisco WAN :: 3845 System Returned To ROM By Bus Error At PC
Jan 26, 2012I have an 3845 router:Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)After an unexpected reboot it says: System returned to ROM by bus error at PC 0x6323F398, address 0xB0D0B39 at 12:35:09 GMT Fri Jan 27 2012..To troubleshoot this error I need to find out what kind of processor this router has. It doesnt fall in either of the categories descibed in url...
View 4 Replies View RelatedCisco WAN :: 7206 System Returned To ROM By Error
Mar 16, 2011I have problem with the WAN Router 7206. It has been reloaded automatically 2 times since yesterday. [code] I have already put this message to the output interpreter and the solution is upgrading to the latest IOS. But, when I search in the Bug Toolkit about SegV problem, this bug status is still "Open". So, how can I upgrade to the latest IOS if the status of this bug is still open?
View 2 Replies View RelatedCisco WAN :: System Returned To ROM By Bus Error - 7200-G2
Dec 19, 2011When i was changing the class-maps i get lost the router. I have attached the crash log file, am i hitting a bug here? I have many times modified the class-maps on the go without any issues.
View 4 Replies View RelatedCisco :: VG224 On Boot File System Error
Nov 29, 2012Cisco VG224 (R527x) processor (revision 4.1) with 119808K/11264K bytes of memory. Processor board ID FGL150411MN, R527x CPU at 225MHz, Implementation 40, Rev 3.1, 1 On-Board Twenty-Four FXS Analog Voice Module V2.1, 2 FastEthernet interfaces, DRAM configuration is 64 bits wide with parity disabled. 63K bytes of non-volatile configuration memory. System fpga version is 250027, % Crashinfo may not be recovered at flash:crashinfo, % This file system device reports an error.
View 4 Replies View RelatedCisco WAN :: 3825 System Returned To ROM By Bus Error 0x6125DCFC
Aug 29, 2012I have a router cisco 3825, It is being restarted autometically. and gives a message "System returned to ROM by bus error at PC 0x6125DCFC, address 0x15A3C78B" in show ver.
View 5 Replies View RelatedCisco WAN :: 7206VXR NPE-G2 Crash - System Returned To ROM By Bus Error?
Dec 27, 2012I noticed that my router 7200 was reboot for a bus error. The error occurred while the system was operational. After the restart the router works properly for more than 6 days.
This is the sh ver:
Cisco IOS Software, 7200 Software (C7200P-IPBASEK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 22:57 by prod_rel_team
[code].....
Seems that the error "System returned to ROM by bus error at PC 0x2E0BF30, address 0x0" should be a special type of bus error crash is when the crash is caused by a corrupted program counter (PC). The PC value is the location of the instruction which the processor was executing when the bus error occured. In this case, the PC has jumped to the address 0x0 (probably because of a null pointer), but this is not where the instruction is located.
Can I consider this as a processor memory parity errors and wait for a second parity error before I replace anything?
Cisco :: 3500 Series AP Gets WCS System Error Page Message
Jan 8, 2013Just upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 5 Replies View RelatedCisco Switching/Routing :: 3560 - System Returned To ROM By Error
Dec 16, 2011My switch is getting restarted and the error shown is : System returned to ROM by error - Debug Exception (Could be NULL pointer dereference)
View 4 Replies View RelatedCisco Infrastructure :: 7206 Router Self Reboot / System Returned To ROM By Bus Error
Sep 10, 2012Whenever I want to turn off the ip cache flow and enter command "no ip flow egress" on a router interface, the router will self reboot and returned with the error message - System returned to ROM by bus error at PC message in the show version ouput.
I tried on two different routers below here and both also undergoing a cold restart when I key in the command "no ip flow egress" on the said interface
1) Cisco 7206 running IOS 12.4(1c)
interface GigabitEthernet0/1
ip address 10.20.10.2 255.255.255.0
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/1 and the router self restarted and return the message Router uptime is 3 minutes System returned to ROM by bus error at PC 0x606D48FC,address 0x0
2) Cisco 3845 running IOS 12.4(3e)
interface GigabitEthernet0/0
ip address 10.20.20.2 255.255.255.0
ip nbar protocol-discovery
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/0 and the router self restarted and return the message
Router uptime is 3 minutes System returned to ROM by bus error at PC 0x6007EBE0, address 0x0
Cisco Switching/Routing :: System Returned To ROM By Reset SP Error Of 7606-S
Jan 15, 2012I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
Cisco Switching/Routing :: 3560 - System Returned To ROM By Address Error At PC 0x0
Jun 7, 2012We have observed that one of the 3560 switch was rebooted with "System returned to ROM by address error at PC 0x0, address 0x0"
View 1 Replies View RelatedDell :: Dimension 8400 - Parity Check / Memory Error And System Halted
Oct 15, 2004I'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
Dell :: 3520 DHCP Client Not Starting With System Error 5 Access Denied Message
Feb 7, 2013I have Dell Inspiron 15 3520 laptop bought in December 2012 with Windows 8 Pro. It was working fine until two days ago. I am unable to obtain DHCP lease either through wireless or wired network. After troubleshooting, I found DHCP service is not running and try to restart but of no avail.I ran sfc /scannow and the results are OK.
View 2 Replies View RelatedCisco WAN :: 6509 / System Detected CRC Error Rate On Port ASIC Data Bus Exceed Fatal Threshold
Dec 7, 2010Recently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies View RelatedLinksys Wireless Router :: System No Longer Sees WRT54G
Dec 29, 2011I mistakenly downloaded and installed version 4 firmware when i should have installed version 2. My system (windows ver. 7) no longer sees the wireless router (WRT54G). I no longer have the install CD and the version 2 firmware does not seem to be available on the website. Is my router now dead in the water?
View 1 Replies View RelatedLinksys Wireless Router :: E3000 - No System Port And Wifi Led
Mar 21, 2012I've made an observation that the newer routers above my E3000 don't have LED icons to indicate the port is connected/active and also to show Wi-Fi is active? I find this good at a glance without having to go look in the back of the unit to see which ports are open etc.
View 1 Replies View RelatedLinksys Wireless Router :: Wrt54gl / How To Change Security On System
Dec 25, 2011I need to change how my security is set on my wrt54gl... it has been so long I don't know the name or password I put it under.
View 1 Replies View RelatedLinksys Wireless Router :: Wrt54g - How To Allow System With Static IP E2000
May 27, 2011I have one system running as a fale server in my house, upgraded my wrt54g to an e2000 and that server cannot get through therouter. if I switch to dhcp it works fine, then switch bake to a static ip outside the dhcp range and use the same mask, gateway, nds,etc I can ping the router but can't get through it. If I then reboot the router it will work for a short time but eventually stop and I have to reboot the router again. I haven't setup any kind of restrictions or other security, server is wired not wireless.
View 2 Replies View Related