When i was changing the class-maps i get lost the router. I have attached the crash log file, am i hitting a bug here? I have many times modified the class-maps on the go without any issues.
View 4 RepliesI have an 3845 router:Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)After an unexpected reboot it says: System returned to ROM by bus error at PC 0x6323F398, address 0xB0D0B39 at 12:35:09 GMT Fri Jan 27 2012..To troubleshoot this error I need to find out what kind of processor this router has. It doesnt fall in either of the categories descibed in url...
View 4 Replies View RelatedI have problem with the WAN Router 7206. It has been reloaded automatically 2 times since yesterday. [code] I have already put this message to the output interpreter and the solution is upgrading to the latest IOS. But, when I search in the Bug Toolkit about SegV problem, this bug status is still "Open". So, how can I upgrade to the latest IOS if the status of this bug is still open?
View 2 Replies View RelatedI have a router cisco 3825, It is being restarted autometically. and gives a message "System returned to ROM by bus error at PC 0x6125DCFC, address 0x15A3C78B" in show ver.
View 5 Replies View RelatedI noticed that my router 7200 was reboot for a bus error. The error occurred while the system was operational. After the restart the router works properly for more than 6 days.
This is the sh ver:
Cisco IOS Software, 7200 Software (C7200P-IPBASEK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 22:57 by prod_rel_team
[code].....
Seems that the error "System returned to ROM by bus error at PC 0x2E0BF30, address 0x0" should be a special type of bus error crash is when the crash is caused by a corrupted program counter (PC). The PC value is the location of the instruction which the processor was executing when the bus error occured. In this case, the PC has jumped to the address 0x0 (probably because of a null pointer), but this is not where the instruction is located.
Can I consider this as a processor memory parity errors and wait for a second parity error before I replace anything?
My switch is getting restarted and the error shown is : System returned to ROM by error - Debug Exception (Could be NULL pointer dereference)
View 4 Replies View RelatedWhenever I want to turn off the ip cache flow and enter command "no ip flow egress" on a router interface, the router will self reboot and returned with the error message - System returned to ROM by bus error at PC message in the show version ouput.
I tried on two different routers below here and both also undergoing a cold restart when I key in the command "no ip flow egress" on the said interface
1) Cisco 7206 running IOS 12.4(1c)
interface GigabitEthernet0/1
ip address 10.20.10.2 255.255.255.0
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/1 and the router self restarted and return the message Router uptime is 3 minutes System returned to ROM by bus error at PC 0x606D48FC,address 0x0
2) Cisco 3845 running IOS 12.4(3e)
interface GigabitEthernet0/0
ip address 10.20.20.2 255.255.255.0
ip nbar protocol-discovery
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/0 and the router self restarted and return the message
Router uptime is 3 minutes System returned to ROM by bus error at PC 0x6007EBE0, address 0x0
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
We have observed that one of the 3560 switch was rebooted with "System returned to ROM by address error at PC 0x0, address 0x0"
View 1 Replies View Relatedwhat does this log message mean? (RV120W fw 1.0.3.10)
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:59:26 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:18:46 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:18:46 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
2012-05-14 19:13:36 warning HERMES kern KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK
[code]....
I got this error this operation returned because the timeout period expired error code 0x000005b4
View 1 Replies View RelatedOSPF-4-ERRRCV: Received invalid packet: Bad LLS Checksum with one of our tunnels
View 1 Replies View Relatedi have a problem with the playstation 3 system when i sign in it takes a while todo that all of a sudden a error appeared on my screen saying "An error occured (80023121)" and me and my dad try to fix the problem but nothing seems to be working
View 1 Replies View RelatedCisco VG224 (R527x) processor (revision 4.1) with 119808K/11264K bytes of memory. Processor board ID FGL150411MN, R527x CPU at 225MHz, Implementation 40, Rev 3.1, 1 On-Board Twenty-Four FXS Analog Voice Module V2.1, 2 FastEthernet interfaces, DRAM configuration is 64 bits wide with parity disabled. 63K bytes of non-volatile configuration memory. System fpga version is 250027, % Crashinfo may not be recovered at flash:crashinfo, % This file system device reports an error.
View 4 Replies View RelatedJust upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
View 5 Replies View RelatedIve tried to reinstall XP, to redownload driver, to reinstall driver etc...
View 9 Replies View RelatedTrying to install WMP54G v4.0 on XP SP3. I have tried all three PCI slots. Removing driver RT2500.SYS system will boot. Put it back and BSOD Error:driver_irql_not_less_or_equal
View 8 Replies View RelatedI'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
I have Dell Inspiron 15 3520 laptop bought in December 2012 with Windows 8 Pro. It was working fine until two days ago. I am unable to obtain DHCP lease either through wireless or wired network. After troubleshooting, I found DHCP service is not running and try to restart but of no avail.I ran sfc /scannow and the results are OK.
View 2 Replies View RelatedRecently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies View RelatedI have received emails in my inbox to say that emails i have sent have been returned but they are in chinese and I haven't sent them.
View 2 Replies View RelatedI have a new Win 7 Dell Precision Workstation that will not log in to my domain. I get an error that there is no login server available if I attempt to log in using a domain account. I log in as the local admin and then try to join a domain using the Join a Domain or Workgroup wizard. I then get an error stating "this operation returned because the timeout period expired". I have had to reset my core switch to get a couple of the new boxes (including this one) to even join the domain. I also show no internet in the Network and Sharing Center most of the time.
View 2 Replies View RelatedI want to use chanelized POS PA in 7200 router. I want to know can I use chanelized PA for both chanelized and non-chanelized OC3/STM1? Does the both chanelized and non-chanelized feature is supported on chanelized module or I have to use other module?
View 1 Replies View RelatedI ran across this today on a 7200 that when all the vty lines are filled, and dont release, you enter clear line vty x and it is supposed to release the line. Well in some versions it doesn't work.
Here is the work around I found. clear tcp line vty x
I want to monitor my 7200's CPU packets per second rate.Any command i can run to show this?Or any MIB so I can poll this? 7200 NPE-G1 can handle 1mpps. And i want to verify the actual rate.
View 1 Replies View RelatedI want to know a number of maximum tcp connection at same time on interface of my 7200 router, how I'll do that?
View 3 Replies View RelatedI am having issues with frequent bgp flaps on the Cisco 7200 series router from past 1 week. I have raised a ticket with ISP but couldn't get any resolution from them as the flap is for about 2min.When ever we see BGP flap, we are not able to ping the remote end IP, Also at that point we drops on the interface connected to ISP.
View 1 Replies View RelatedI was recently given a Cisco 7200 VXR and told to erase the stored configurations in it. how to do erasing of Cisco 7200 stored config else I might have to delete them line by line.
View 4 Replies View RelatedWe have network consisting of approx. 8 7200's running LNS/MPLS/BGP and we provide predominantly private networks to clients(Majority of client networks are a mix of Ethernet tails and DSL).We have received a request from one client to support multicast - Having never implemented multicast, have a few questions:
1. Is is supported/possible to provide multicast within a vrf on 7200's?(From initial investigations, it appears to be)
2. Is it possible to only enable mutilcast in a vrf(i.e. not globally)?
3. Any recommended guides/best pratices?(Googling has revealed nothing really that is similiar to what we want to do)4. What are the potential ramifications?(Resource overhead, Security implications, anything else?)
I am planning to provide a redudnt link to our customer. The setup as below:
One link over wireless while the other link over wired link, I want to make sure that I should maintain the same public IP addresses for the customer therefore, I am looking for L2 failover for my customer.
If the wireless down the customer should migrated to wired and vis versa. I have 7200 CISCO Router as Core.
I am trying to configure a dynamic failover with IP SLA on a Cisco 7200 using 12.2(33) IOS. I would like to have something similar as the following configuration:
ip sla monitor 1type echo protocol ipIcmpEcho x.x.x.xfrequency 3ip sla monitor schedule 1 life forever start-time now!!track 10 rtr 1 reachability
access-list 101 permit icmp any host X.X.X.X echo!route-map LOCAL_POL permit 10 match ip address 101 set ip next-hop Y.Y.Y.Y set interface Null0!ip local policy route-map LOCAL_POL
!
ip route XX.XX.XX.XX 255.255.255.0 YY.YY.YY.YY track 10ip route XX.XX.XX.XX 255.255.255.0 ZZ..ZZ.ZZ.ZZ 254
My questions are the following
Question 1: What is the equivalent of ip sla monitor in 12.3 for dynamic failover with IPsla Should I used
ip sla ethernet-monitor 1 type echo domain name ?
or
ip sla 1 path echo X.X.X.X or ethernet mpid echo domain name or icmp-echo time out 1000 frequency 3 threhsold 2
I do not know if I have to used ethernet-monitor or ip sla. What is the domain name and the mpid associated to the ethernet-monitor ip sla.In the case where I have to used ip sla 1, shoud I used a path-echo, ethernet mpdi or icmp-echo for dynamic failover
Question 2: In 12.3, what is the equivalent to ip sla monitor schedule 1 life forever start-time now.I have found thec command ip sla schedule 1 start now but it does not seems that we could configure the duration.
Question 3: Should I also enable ip sla responder
I have a 7200 router with a 12.2.(46a) IOS and I am trying to activate Netflow on a subinterface. From the documentation of Cisco, I should be able to do it since the ios 12.2.(14)S but the command is unavailable.
[URL]
I have tried also to enter the command in the subinterface directly but it doesn't recognize it.
We have a Cisco 7204 G1 running c7200-advipservicesk9-mz.122-33.SRE7.bin and we're having a lot of difficulties getting a VTI working to a Cisco 2921 with adv. security. I've ruled out that the 2921 is at fault by successfully establishing a VTI to another 2921 and a 7200 running a different IOS release.
We see the tunnel come up, but when I sent a ping from the 2921 to the 7204 there isn't a reply. When I look at the results on the 7204 from a 'sh crypto engine connection active', I see the decrypt counters increase, but I don't see the Encrypt counters increase as it's trying to reply to the ping. I'm not sure if this is because there is an issue with the encryption or whether there might be a more fundamental issue with the router not replying to the pings.
I've tried the following IOS releases (c7200-advipservicesk9-mz.122-33.SRE7 & c7200-advipservicesk9-mz.122-33.SRE6) and they all behave the same way - this makes me think it might be a config issue rather than and IOS bug which is what I first thought. c7200-advipservicesk9-mz.122-33.SRE7.bin.
sh crypto engine connections active
Crypto Engine Connections
ID Interface Type Algorithm Encrypt Decrypt IP Address
1 Tu10 IPsec 3DES+SHA 0 31 10.5.5.1
2 Tu10 IPsec 3DES+SHA 19 0 10.5.5.1
1001 Tu10 IKE SHA+3DES 0 0 10.5.5.1
Here is a copy of my config on the 7204 - the other end (Cisco 2921) is configured in the same way.
crypto isakmp policy 1
encr 3des
authentication pre-share
[code].....