Cisco Infrastructure :: 7206 Router Self Reboot / System Returned To ROM By Bus Error
Sep 10, 2012
Whenever I want to turn off the ip cache flow and enter command "no ip flow egress" on a router interface, the router will self reboot and returned with the error message - System returned to ROM by bus error at PC message in the show version ouput.
I tried on two different routers below here and both also undergoing a cold restart when I key in the command "no ip flow egress" on the said interface
1) Cisco 7206 running IOS 12.4(1c)
interface GigabitEthernet0/1
ip address 10.20.10.2 255.255.255.0
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/1 and the router self restarted and return the message Router uptime is 3 minutes System returned to ROM by bus error at PC 0x606D48FC,address 0x0
2) Cisco 3845 running IOS 12.4(3e)
interface GigabitEthernet0/0
ip address 10.20.20.2 255.255.255.0
ip nbar protocol-discovery
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/0 and the router self restarted and return the message
Router uptime is 3 minutes System returned to ROM by bus error at PC 0x6007EBE0, address 0x0
I have problem with the WAN Router 7206. It has been reloaded automatically 2 times since yesterday. [code] I have already put this message to the output interpreter and the solution is upgrading to the latest IOS. But, when I search in the Bug Toolkit about SegV problem, this bug status is still "Open". So, how can I upgrade to the latest IOS if the status of this bug is still open?
I have an 3845 router:Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)After an unexpected reboot it says: System returned to ROM by bus error at PC 0x6323F398, address 0xB0D0B39 at 12:35:09 GMT Fri Jan 27 2012..To troubleshoot this error I need to find out what kind of processor this router has. It doesnt fall in either of the categories descibed in url...
When i was changing the class-maps i get lost the router. I have attached the crash log file, am i hitting a bug here? I have many times modified the class-maps on the go without any issues.
I have a router cisco 3825, It is being restarted autometically. and gives a message "System returned to ROM by bus error at PC 0x6125DCFC, address 0x15A3C78B" in show ver.
I noticed that my router 7200 was reboot for a bus error. The error occurred while the system was operational. After the restart the router works properly for more than 6 days.
This is the sh ver:
Cisco IOS Software, 7200 Software (C7200P-IPBASEK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1) Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc. Compiled Thu 28-Oct-10 22:57 by prod_rel_team
[code].....
Seems that the error "System returned to ROM by bus error at PC 0x2E0BF30, address 0x0" should be a special type of bus error crash is when the crash is caused by a corrupted program counter (PC). The PC value is the location of the instruction which the processor was executing when the bus error occured. In this case, the PC has jumped to the address 0x0 (probably because of a null pointer), but this is not where the instruction is located.
Can I consider this as a processor memory parity errors and wait for a second parity error before I replace anything?
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file ================= Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38 Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0 05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ====================== Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1) Technical Support: [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc. Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1) BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1) [Code]...
Customer site connected to a PE using 2 x E1 circuits aggregated using Multilink PPP. The CE is a 1760, and the PE is a 7206. This is the customer HQ site.
Connected to the same PE are three other sites from the same customer. Each is connected with a single E1, again each CE is a 1760.
During some testing the customer did some large file transfers concurrently from each of the three remote sites into the HQ, so we had data coming into the PE via the three E1's (6Mbps) and then being routed onto the 4 Mbps Multilink PPP interface into the HQ, which is a potential bottleneck. This test failed miserably with packets being dropped on the output interface on the PE facing the HQ.
But then if Multilink PPP encap is removed, and we just connect the HQ using one E1 with HDLC encapsulation, the test works, even though we have half the bandwidth to the HQ, so an even greater potential bottleneck.
I have a DLSW connectivity between 2800 series router and 7206 router. AS 400 is directly connected to 2800 series router and other server is connected directly to 7206 router. now i want to add one more server which will work as backup for the server connected to 7206 . What would be the connectivity/configuration to make it working in case primary server connected to 7206 is down or connection would automatically needs to shift on its backup server.
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
I recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
I need to order LMS for one of our customer with 500 devices and reporting capabilities ..... So i chose base license "R-PI-1.1-K9" and 500 device license "R-PI-1.1-500-K9" and Compliance Management - 500 Device License "L-PI-1.1-CM-500"? i tried to search server capability for my requirements & Operating system and couldn't find it .....
1) What is the server requirements ?
2) What is operating system (windows 2008 or VMWare VMware ESX/ESXi Version 4.1 or 5.0)
I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. [code]
I have a brand new 2960S-48TS-L, plain vanilla with no extra module/boards etc. It boots up ok (the installed version is 12.2 (55) SE5) but then constantly cycles the following error, and doesn't accept any input whatsoever. After 5-10 minutes of cycling the error, the switch reloads and starts the process again.
PCIE0: link is NOT up. --------------CPU's PCIe SDR Registers-------------------- PE_DLPSET = 00401000 PE_UTLSET1 = 00000000
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
i have a problem with the playstation 3 system when i sign in it takes a while todo that all of a sudden a error appeared on my screen saying "An error occured (80023121)" and me and my dad try to fix the problem but nothing seems to be working
Cisco VG224 (R527x) processor (revision 4.1) with 119808K/11264K bytes of memory. Processor board ID FGL150411MN, R527x CPU at 225MHz, Implementation 40, Rev 3.1, 1 On-Board Twenty-Four FXS Analog Voice Module V2.1, 2 FastEthernet interfaces, DRAM configuration is 64 bits wide with parity disabled. 63K bytes of non-volatile configuration memory. System fpga version is 250027, % Crashinfo may not be recovered at flash:crashinfo, % This file system device reports an error.
Just upgraded our WCS server to the 7.x code over the weekend. Turned up the first 3500 series AP's today. The AP's have been up for about an hour. I am seeing the Air Quality graphs on WCS. On the Worst 802.11a/n and 802.11b/g/n Interferers windows, I am see a WCS System Error Page message but only in those windows. I have gone over the documentation and dont see that I need to enable anything else on WCS.
After a successfull installation of NCS 1.2 into a vmware environment and run the setup I have the following error while trying to start or to have a status for NCS (ncs start ot ncs status):sh: /opt/CSCOlumos/bin/wcsadmin.sh No such file or directory
I'm trying to use the IP phone directory xml url in my UCCX script to use for "Calling Name" presentation and the Set enterprise presentation parameter for the CAD where (if found Calling name) it will be presented. This is working, but if the Calling Name includes special characters the script fails with a UTF 4-8 encoding error double byte....bla. something popup in the script. See a snippet of my CCX code "attached" where in the "Get xml document data" i get the exception and the script fails when it see a Calling name with the character: Ó
Question: is is it possible to handle UTF exceptions in a UCCX script?
I am trying to find some background information regarding this error:
Cisco 6500 [SUP720-3B] %QM-4-AGG_POL_EXCEEDED QoS Hardware Resources Exceeded Out of Aggregate policers.
What triggers this error? In this case, there are QoS policies configured at the interface level. The 'show platform hardware capacity' command shows that there are1024 policers supported. What counts as a policer? Is a policer each instance of a class using the police command? I see where there have been some suggestions to use VLAN based policies instead of interface policies and others suggesting to turn off 'qos marking statistics' but I would really like to understand the details of what causes policers to be used up and how to approach fixing this.
I am trying to understand how this works under the covers but can't seem to find any documentation anywhere defining the details.
I have windows server 2008r2 running a FTP server, so I can back up my configs and upgrade IOS when needed. My problem is than I can backup to the server just fine but when i try and restore a config or pull a new IOS over it gives me this error
%Error opening ftp://13****** (Protocol error) this is happening on every switch I have and I can't figure it out.
Trying to install WMP54G v4.0 on XP SP3. I have tried all three PCI slots. Removing driver RT2500.SYS system will boot. Put it back and BSOD Error:driver_irql_not_less_or_equal
I'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction -NMI: Parity Check/Memory Parity Error -The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
I have Dell Inspiron 15 3520 laptop bought in December 2012 with Windows 8 Pro. It was working fine until two days ago. I am unable to obtain DHCP lease either through wireless or wired network. After troubleshooting, I found DHCP service is not running and try to restart but of no avail.I ran sfc /scannow and the results are OK.
Recently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
