I need to order LMS for one of our customer with 500 devices and reporting capabilities ..... So i chose base license "R-PI-1.1-K9" and 500 device license "R-PI-1.1-500-K9" and Compliance Management - 500 Device License "L-PI-1.1-CM-500"? i tried to search server capability for my requirements & Operating system and couldn't find it .....
1) What is the server requirements ?
2) What is operating system (windows 2008 or VMWare VMware ESX/ESXi Version 4.1 or 5.0)
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. [code]
Whenever I want to turn off the ip cache flow and enter command "no ip flow egress" on a router interface, the router will self reboot and returned with the error message - System returned to ROM by bus error at PC message in the show version ouput.
I tried on two different routers below here and both also undergoing a cold restart when I key in the command "no ip flow egress" on the said interface
1) Cisco 7206 running IOS 12.4(1c)
interface GigabitEthernet0/1 ip address 10.20.10.2 255.255.255.0 ip flow egress duplex auto speed auto end
when I key in "no ip flow egress" under int gi0/1 and the router self restarted and return the message Router uptime is 3 minutes System returned to ROM by bus error at PC 0x606D48FC,address 0x0
2) Cisco 3845 running IOS 12.4(3e)
interface GigabitEthernet0/0 ip address 10.20.20.2 255.255.255.0 ip nbar protocol-discovery ip flow egress duplex auto speed auto end
when I key in "no ip flow egress" under int gi0/0 and the router self restarted and return the message
Router uptime is 3 minutes System returned to ROM by bus error at PC 0x6007EBE0, address 0x0
I have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G Total Output Errors 0 47749 Small Buffer Misses 4 misses 139 misses
I want to implement QoS on our Core router but the core router makes use of GRE Tunnels to remote branch locations.so far all QoS techniques i want to use cannot be implemented using tunnel interfaces.
the core router is a cisco 7604 router with IOS version 12.2 (33)SRE while the remote locations have ISRs (2821).
Which QoS technique to use with respect to GRE Tunnels as there are times of congestion due to heavy network traffic to those remote locations.
We have a CISCO 7604 Router (GGSN) in our customer site. Since two weeks are observing high CPU utilization (even touching 100 percent). We performed a SNMP configuration on this routers 2 weeks back as well. But SNMP process is not consuming much CPU resources. The following is the output of the "show proc cpu" and "show proc cpu history.
------------------ show process cpu ------------------ CPU utilization for five seconds: 50%/15%; one minute: 49%; five minutes: 51% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
I have a 7604 Edge router that connects to our Data centre via Fiber.
but i keep getting input errors on the interface Gi3/5. i also found out that i cannot change the duplex settings on the edge router to auto, i only have two options of full and half and changing it has not worked either.
I have tried to use a switch in between the fiber modem and the edge router to try to manipulate the duplex settings, but when i tried it the port simply shutdown and then i have to reverse the configuration.
The software version of the router is 12.2(33)SRE3, i really need to sort this out as connection to and from the Data centre is quite slow.
what is the meaning of the following log messages on Cisco 7604 Core routers. The Core router is configured with 2 STM card configurations with Vlan assignments: [code]
We currently run 7206 routers with VAM cards and are able to configure the devices to perform stateful failover of tunnels from router to router. When moving to the 7604 with 15.1 IOS there are not any examples of how to set up the stateful failover of the tunnels between devices. We have the devices in the SSO mode are not able to understand how to get the redundancy between the devices functioning.
I have 7604 router with FWSM module in module 3.First of all the FWSM CF has been damaged, not physically. I bought the new same compact flash (size, partnumber, etc.). Downloaded the software 3.2 for FWSM, and ASDM from Cisco website. I realized that the procedure of creating new CF for FWSM is quite diffucult: creating 1-5 partitions, where 1 - is MP, and 4th - application partition. According to cisco documentation - the default boot partition is the 4th, so I partitioned from 7604 the CF into 4 partitions (partition disk1: <1-4> maximum) and copied the software and ASDM to the 4th partition (disk1:3:). Removed the CF from the router and put it into the FWSM module.
i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------ Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
I have two 7604 routers running IOS 12.2(33)SRB5a as ASBRs in my network. They both connect to a common AS via DS3 lines.FR01 is considered my main circuit, FR02 is the backup. But I have some heavy disk sync traffic I want to route via the backup unless that circuit is down.How could a static redistribution possibly influence all my routes ?
Here is the remote AS config on both routers. We summarize the routes and only change the redistribute metric to distinguish main from backup circuit :
i read alot about password recovery , but when i apply it to cisco 7604 it fails ?i went to rommon mode and typed# confreg 0x2142 then i typed reset when the router startup it request a password form me ,i can enter the user mode , and when i type sh ver command i note that the config resgitser is 0x2102 , not 0x2142 !!!!
i could enter the privilage mode !!!! and seems no thing changed ! does this router has a specific password recovery procedure ? which differes than the classic procedure?
I was called into a company today to look at their Cisco 7604 router as it had stopped working. The supervisor has all it LED in orange state, there was no blinking of the lights at power on they went straight to orange. Tried removing all cards, having only supervisor card in, etc but always the orange lights.
Assuming I have the following setup: Cisco 7604 Cisco Systems Cisco 7600 4-slot Chassis System OSR-7600 Clock FRU 1 & 2WS-F6K-MSFC2A Cat6k MSFC 2A daughterboard Rev. 4.0 WS-F6K-PFC3B Policy Feature Card 3 Rev. 2.4 WS-SUP32-GE-3B 9 ports Supervisor Engine 32 8GE Rev. 4.6 WS-X6148A-GE-TX 48-port 10/100/1000 RJ45 EtherModule Rev. 4.1WS-X6548-GE-TX SFM-capable 48 port 10/100/1000mb RJ45 Rev. 11.3 The SUP32-3c says it supports both L2VPN and L2TPv3, however the line cards are effectively 6500 line cards and I was under the impression the 6500 didn't support these.
If the supervisor supports a feature does that mean it is globally supported on a switch? Or do I need to check the compatibility of these line cards as to if they support these features?
i have the topology :=========want to mention that im using port address translation on the router & not sure if it is making a conflict .
here is the config below :
why the cache is not working ?i mean that i tried going to internet with source ips of the subnet 10.20.30 , but i seems went to internet without any precedence of cahce server
I am having a problem with PBR done on a 7604-S router - It seems like it is not done in harware. I have an Iperf client and an Iperf server, and would like to test the performance of 7600 router for PBR, supervisor is RSP720-3C-G and used interface card is 7600-ES20-GE3C ESM20G.
I have read numerous discussions about PBR that is supposed to happen in hardware when you use it with matching access-list and set ip next-hop.Although, when I start the iperf, the 7600 cpu is hitting the 80-90 % boundary, and transfer bandwidth can't go over 120-130 Mbit/s.The IP Policy is applied on an interface part of vrf ONE maybe this is casing the problem... ?
The diagram and configuration follows: Configuration:
c7604#sh run boot system flash disk0:c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin ! ip vrf one [Code]...
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
I've got router as vpn-concentrator which receives vpn site-to-site connections from 10 branches with cisco 881 and cisco 1941.I started cacti monitoring and found out that there are too many errors on interfaces.URL.
I have a issue where after configuring aaa and rebooting, logging into the console port seems to be auto trying something before it finally times out and let's the user try. I getting the following sequence: [code] I need aaa to work via vty, however I need the device to boot directly to the Username: prompt so I can continue to use my VB script to clear the config when the devices are return from the field.
Any info concerning the installation of CW LMS 4.0.1 on Solaris 10!
The installation keeps on failing when it is checking for packages. Also the second time when we downloaded the software once more.
ERROR: AddProperty called with invalid package name: CSCOmd.
I have also attached the install log files.
The system is Solaris 10 with zones:
bash-3.00# more /etc/release Solaris 10 10/09 s10s_u8wos_08a SPARC Copyright 2009 Sun Microsystems, Inc. All Rights Reserved. Use is subject to license terms. Assembled 16 September 2009 121133-02, 125503-02, 126897-02, 127127-11, 127755-01, 138866-01 Incompatibles: [Code] .....
I am installing LMS 4.1 to windows 2008 R2 SP1.Server hardware meets requirements.A the end of the installation I am getting from the installation log file the following warnings/errors. [code]
