Cisco Switching/Routing :: HSRP Flapping On 7604?
Jul 9, 2012
i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
[Code]......
View 2 Replies
ADVERTISEMENT
Mar 11, 2012
I am having a problem with PBR done on a 7604-S router - It seems like it is not done in harware. I have an Iperf client and an Iperf server, and would like to test the performance of 7600 router for PBR, supervisor is RSP720-3C-G and used interface card is 7600-ES20-GE3C ESM20G.
I have read numerous discussions about PBR that is supposed to happen in hardware when you use it with matching access-list and set ip next-hop.Although, when I start the iperf, the 7600 cpu is hitting the 80-90 % boundary, and transfer bandwidth can't go over 120-130 Mbit/s.The IP Policy is applied on an interface part of vrf ONE maybe this is casing the problem... ?
The diagram and configuration follows:
Configuration:
c7604#sh run
boot system flash disk0:c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin
!
ip vrf one
[Code]...
View 8 Replies
View Related
Jul 14, 2012
i read alot about password recovery , but when i apply it to cisco 7604 it fails ?i went to rommon mode and typed# confreg 0x2142 then i typed reset when the router startup it request a password form me ,i can enter the user mode , and when i type sh ver command i note that the config resgitser is 0x2102 , not 0x2142 !!!!
i could enter the privilage mode !!!! and seems no thing changed ! does this router has a specific password recovery procedure ? which differes than the classic procedure?
View 4 Replies
View Related
Sep 2, 2012
I was called into a company today to look at their Cisco 7604 router as it had stopped working. The supervisor has all it LED in orange state, there was no blinking of the lights at power on they went straight to orange. Tried removing all cards, having only supervisor card in, etc but always the orange lights.
View 2 Replies
View Related
Dec 7, 2012
i have the topology :=========want to mention that im using port address translation on the router & not sure if it is making a conflict .
here is the config below :
why the cache is not working ?i mean that i tried going to internet with source ips of the subnet 10.20.30 , but i seems went to internet without any precedence of cahce server
[code]...
View 1 Replies
View Related
Jul 9, 2012
Example config
int g2/24
service-policy output test
#and/OR
int g2/24.10
encap dot1q 10
ip address 10.1.1.1 255.255.255.0
service-policy output test
View 5 Replies
View Related
Sep 22, 2011
I recently upgraded my network to have two 3750x core, one interface on the cisco is connecting to a Netgear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
View 2 Replies
View Related
Apr 14, 2013
i have a question, i have in the logging of my switches a mac falpping problem. i have a log notification : Apr 12 19:33:13: %SW_MATM-4-MACFLAP_NOTIF: Host xxxx.f065.520c in vlan 25 is flapping between port Gi0/1 and port Fa0/35. When i look up what is connected to interface FA0/35 it is a accespoint " AIR-AP1242G-A-K9" Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
How this is making the mac flapping ?
View 2 Replies
View Related
Jun 27, 2012
We have been receiving these notifications on one of our core.
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host b407.f9c3.3c51 in vlan 56 is flapping between port Po5 and port Te7/2
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 145a.05c8.0ed3 in vlan 802 is flapping between port Te7/2 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 9463.d129.546a in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 3c43.8ef3.7448 in vlan 56 is flapping between port Gi2/9 and port Po5
Jun 28 12:54:01: %MAC_MOVE-SP-4-NOTIF: Host 000e.35eb.25ae in vlan 66 is flapping between port Po5 and port Te7/2
PO5 goes to our primary wireless controller. Gi2/9 goes to a Cisco 4500 switch that also has a PO5 on it for a failover lan controller and TE7/2 is another core switch.
These mac-address all seem to point to PO 5 which is the port channel assigned to Wireless Controller interfaces.
How do I determine if this is a spanning-tree loop? No ports are err-disabled.
View 8 Replies
View Related
Jun 4, 2012
We have some legacy Cisco 6513 switches with the backbone (16-port GBIC blade) MTU set to 1500. It has a WS-X6148A-GE-TX blade as well, MTU set to 9K.
Now we have a customer sending MTU of 1546, their copper interface terminating on WS-6148A keeps flapping. Does the flapping have something to do with the backbone set to 1500? We cant set the backbone to 9K at this moment since it may be intrusive (reuire a reboot).
View 1 Replies
View Related
Feb 27, 2012
We have two switches WS-C2960S-24TS-L running in stack with running IOS c2960s-universalk9-mz.122-55.SE3.We have connected two checkpoint devices on Gi1/0/24 and Gi2/0/24 with a simple configuration:
interface range GigabitEthernet1/0/24, gi2/0/24
switchport access vlan x
switchport mode access
spanning-tree portfast
On the devices log we get the following message:
%SW_MATM-4-MACFLAP_NOTIF: Host 0000.0000.fe21 in vlan x is flapping between port Gi2/0/24 and port Gi1/0/24
The mac-address 0000.0000.fe21 is not found on any checkpoint interface. "Show mac-address int gi1/0/24 or gi2/0/24" does not show the correct mac-address of the checkpoint interface connected to the port, but instead shows 0000.0000.fe21.Is there a bug in the IOS, something wrong with the switch config or does it have something to do with the checkpoint config?
View 2 Replies
View Related
Nov 15, 2011
This is the message that I am getting from my 1941w router. I have a isakmp tunnel built with a GRE tunnel going through it.
View 15 Replies
View Related
Mar 28, 2013
Lately I have been noticing mac flap messages on some of our access layer 3750G switches. Just a little background on how this is setup.
These 3750G switches are stacked and uplinked to a distribution layer 3750E stack (2 switches) via cross stacked etherchannel. (Usually 4 links) The access layer switches are stricly layer 2 where the distribution layer 3750E is routing the VLANs at the access layer to to the core 6500 switches.
I have just about ruled out physical loops on these stacks for the reason that the Macs are flapping. I am seeing this on two different stacks now each having 3 switches in the stack at the access layer. The cross stack etherchannel is spanned across the first two switches at the access layer and connected to both switches at the distribution layer. I have checked the etherchannel status and all ports appear to be part of the etherchannel and they appear fine.
The mac addressses that are flapping are just plain old desktop machines that plug directly into the access layer. I usually see this when the mac is learned on a port such as when a machine is plugged into the network or reboots.
View 6 Replies
View Related
Dec 6, 2012
Two days back my entire network was behaving in unusual ways.When is connect to core switc(4506e) through console. [code]
View 11 Replies
View Related
Mar 5, 2013
Would like to ask whats the correct snmp config so that it will send to our snmp server when a mac flapping occurs on a cisco switch specifically 4507 switches.
View 6 Replies
View Related
Aug 27, 2012
I work for a Wireless ISP and the device impacted is the back haul radio into the site. I have swapped from a 2950T to a 3550. Replaced the radio, PoE, patch lead. We have re ran the cable up the tower using shielded outdoor cable with a drain wire which has been earthed to an earthing block in the cabinet. We have other devices on the tower not experiencing the issue. We suspect cable interference however am now at a loss to diagnose further.
[Code]....
View 3 Replies
View Related
Feb 4, 2013
I have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
View 1 Replies
View Related
Mar 10, 2012
We have a pair Cisco 6509 switch in which 2 * 48 Port 1G line cards and 1 * 16 Port 10G line Card, FWSM and Sup 720 are installed.We have Cisco UCS and HP Blade servers.Cisco UCS servers are connected to Cisco 6509 switch using Fabric Interconnect, and HP Servers are directly connected to core switches.Recently the team made many changes in the network. Upgraded the IOS in Cisco 6509 switch, Configured Port profiling , MAC Pinning , HBA Cards to UCS / Nexus 1000V Infrastructure. After this change they lost the connectivity to UCS and HP Serers. Every tower is checking at their end.
The Network Team has reverted back the core switch with old IOS , but still the problem persisit.I could only see the following error log in the core switch. There are two port-channels one between core 1 and core 2. The other is between core switch and FWSM module. [code]
View 2 Replies
View Related
Jul 23, 2012
we have cisco 2960 switch which is connected to a cisco 2811 router. flapping issue between these two devices??
The following actions i have taken, but no result.. I have changed cables. have set speed to 100 and duplex full on both the interfaces but the interfaces are showing up up still not getting connectivity. same i have to auto on both sides still no result what configurations should i set to resolve this issue...?
View 10 Replies
View Related
Oct 2, 2012
I have Cisco 1811 and Cisco 2960 interconnect with each other by TRUNK link. As time pass i recieving below log on cisco 1811 router.
DTP-5-NONTRUNKPORTON: Port Fa8 has become non-trunk
LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne t8, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan200, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan300, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan400, changed state to down
View 4 Replies
View Related
Sep 15, 2012
I recently upgraded my network to have two 3750x core, one interface on the Cisco is connecting to a Net gear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
003396: Sep 17 01:46:16.328: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003397: Sep 17 01:46:19.843: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003400: Sep 17 01:49:58.769: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/17, changed state to down
[Code] .....
After my research i think this is a looping issue but I'm unsure how to address it.
View 2 Replies
View Related
Jun 2, 2013
i just configured a C6K VSS with Sup2T, 15.1SY IOS software and a WS6724-SFP module with the follwing cos config:
auto qos default
table-map cos-discard-class-map
map from 0 to 0
map from 1 to 8
map from 2 to 16
[code]....
After applying the service policy to one interfac of the WS6724-SFP module the policy is deployed to all interfaces of the module. So far it should be ok but after a short time all interface of the module begin to go down an up and down and up ... flapping.
View 1 Replies
View Related
Feb 22, 2012
Stange problem which I encountered today, I have a Cisco 2960 which is connected to a netgear. The switch started showing itself in CDP and was running STP. I checked the cables physically today and noted 3 uplinks to the netgear, all port on the Cisco active and forwarding and green lights.
The Cisco was running STP, I changed it to R-PVST and the lights on the Cisco went crazy and I got the message port flapping on the switch but the switch did not block any ports (all ports on same vlan).
There after I changed it back to stp and the switch blocked the other up links apart from one.
Sure R-PVST is far superior than STP?
View 5 Replies
View Related
Aug 27, 2012
I am receiving the following error message on a Cisco 3750 switch stack. Need troubleshooting this error message.
00:03:13: %SW_MATM-4-MACFLAP_NOTIF: Host 00d0.7400.2730 in vlan 600 is flapping between port Gi2/0/3 and port Gi2/0/2
View 3 Replies
View Related
Sep 11, 2012
I have two Core 6509E SUP2T configued as VSS and has two 48 ports fiber blades. I have two 3750s, I have two gig on each 3750 port-channle to po1 and connected to both the core, one link to each core.Now, I was asked ot add two more links on each 3750 switch to make it a total of 4 gigs on each 3750s (all 4 gig ports/uplinks will be in used an dtwo links to core one an dtwo links to core 2).when i added two additional links on 3750s and bundled them to po1, I created another port channel on core and bundeled the additional two gigs on each core to accomodate for the two additional links (ports on core switches are not consequtives).
adding these two additional ports makes the 3750 switches flap between managemnet vlan and po1.now, i am not sure if I must have added the two additional links on the core to teh current port-channel or core!? I have created another port-channel on core to accomodate for this currently!?
View 26 Replies
View Related
Mar 11, 2012
I have an issue with a Cisco 3750 switch stack which is connected to two seperate upstream Cisco 3750's which are administered by an ISP. The ISP is experiencing MAC address flapping from one of my VLAN SVI's i am using to route traffic upstream
[code]...
As you can see I utilise a VLAN SVI to route traffic to the upstream 1.1.1.2 (illustration only) IP. As per the diagram of the topology attached, the ISP is receiving a MAC address flapping error confirming the SVI MAC address from my switch stack is being learnt on the trunk port connecting switch 1 and switch 2, and also the port (Gi1/0/48) directly connected to my switch stack. As these are all Layer 2 links essentially being passed upstream and then connected between the two ISP switches, we have a 3 way triangular loop formed.
If I was to remove the port channel configuration from the two ports associated with the VLAN SVI, am i right in suggesting this would still form a layer 2 loop? The two ports would still be a member of the SVI VLAN, and it is the VLAN MAC address which is being learnt by the two ISP switches on different interfaces.
View 2 Replies
View Related
Oct 18, 2011
I am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
View 5 Replies
View Related
Apr 30, 2012
show logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
View 2 Replies
View Related
Oct 7, 2012
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
View 4 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Jan 8, 2012
I want to setup HSRP between three 6509 switches with a single virtual ip for all the three switches.
know if its possible and share any site or config.
View 1 Replies
View Related
Nov 11, 2012
I'm looking to try and implement ipv6 HSRP on a series of IOS-XR Routers running 4.2.1 following on from successfully setting up IPv6 HSRP on a few cat6509s on VLAN Interfaces in other parts of the network. I have entered the "router hsrp" configuration menu and gone into the interface in question that I'm looking to setup with IPv6 HSRP. Unfortunately, there version 2 or address-family ipv6 commands are not available.
View 2 Replies
View Related
Apr 17, 2012
is it possible to run hsrp on two routers (not l3 switch) connected to a l2 switch ? if so does the two routers need a back to back connection ?
i know if use two l3 switches (instead of routers) and connect to a LAN switch then we need a back to back connection between the L3 switches
also can we use hsrp on vss on 6500?
design
1800 router 1800 ROuter
| |
| |
|---------- L2 switch-------------------------------|
if the above design is acceptable how does the routers know which one is active and which one is standby ? if we need a direct connection between two routers they have to be on a seperate subnet and routers dont allow broadcasts - so how will hsrp work on routers ?
L3 switch --------------------------l3 switch
| |
| |
|---------------L2 switch---------------|
View 8 Replies
View Related
