Cisco Switching/Routing :: Flapping Between Router (2811) And Switch (2960)
Jul 23, 2012
we have cisco 2960 switch which is connected to a cisco 2811 router. flapping issue between these two devices??
The following actions i have taken, but no result.. I have changed cables. have set speed to 100 and duplex full on both the interfaces but the interfaces are showing up up still not getting connectivity. same i have to auto on both sides still no result what configurations should i set to resolve this issue...?
View 10 Replies
ADVERTISEMENT
Feb 4, 2013
I have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
View 1 Replies
View Related
Feb 22, 2012
Stange problem which I encountered today, I have a Cisco 2960 which is connected to a netgear. The switch started showing itself in CDP and was running STP. I checked the cables physically today and noted 3 uplinks to the netgear, all port on the Cisco active and forwarding and green lights.
The Cisco was running STP, I changed it to R-PVST and the lights on the Cisco went crazy and I got the message port flapping on the switch but the switch did not block any ports (all ports on same vlan).
There after I changed it back to stp and the switch blocked the other up links apart from one.
Sure R-PVST is far superior than STP?
View 5 Replies
View Related
Apr 30, 2012
show logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
View 2 Replies
View Related
Jul 5, 2012
I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
View 2 Replies
View Related
Sep 3, 2012
We have a DHCP SERVER implemented in a cisco router 2610.This router is connected to a switch cisco 2960 configured as DHCP SNOOPING. At the switch appear the next log message: [code] The ip address: 10.100.200.1 belongs to DHCP SERVER configured at router cisco 2610. What to do so these log messages does not appear any more? Do I need to do some configuration changes at some switch or router?
View 11 Replies
View Related
May 12, 2013
I have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
View 9 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
Feb 5, 2013
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
View 5 Replies
View Related
Dec 12, 2006
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies
View Related
Jan 14, 2013
I am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies
View Related
Aug 20, 2012
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
View 3 Replies
View Related
Apr 29, 2012
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
View 5 Replies
View Related
Jan 24, 2012
I am setting up a new 2960-S switch and none of the recommended username and passwords combinations work. I have tried CIsco Cisco, <blank> cisco and various other permutations.
I have tried to reset the switch to factory defaults and it still doesn't work. The switch is currently connected to a 3560G and has been assigned an IP. If I try to access it from Network assistant it shows as unmanaged and I get prompted for a username and password.The switch is connected to another new 2960-S via a FlowStack module.
View 4 Replies
View Related
Mar 31, 2011
I am having an issue get an EZVPN working between a 2811 server and a SR520 client. The symptoms are the SR520 makes multiple connection attempts to the 2811. It appears that sometimes these connections are successful and the SR520 is assigned an IP address but then the tunnel will be dropped and a new session will be started. I've attached scrubed configs for both the 2811 and the SR520. One other note, when connecting to the 2811 with a software VPN client, there are no problems, so I think the problem is with the SR520. On the other hand, the SR520 wasn't having any problems until we switched our VPN server from a UC520 to the 2811.
View 3 Replies
View Related
Nov 28, 2012
I need to know the 172cisco 1 router support to IPv6 & it support to IPv6 then which IOS is required for it.Also I need to know the cisco 2960 switch is support to IPv6?
View 3 Replies
View Related
Feb 19, 2013
Currently Being Moderated password recovery
View 3 Replies
View Related
Feb 16, 2012
I am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
View 4 Replies
View Related
Feb 9, 2012
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
View 5 Replies
View Related
Oct 22, 2012
I have a Cisco 1841 router connected to a Cisco 2960 switch.Users behind the router can't access the internet but when someone is directly connected to the switch with his PC and uses the IP Address found on the WAN port of the router, he's able to go on to the internet. [code]
View 4 Replies
View Related
Mar 8, 2012
Today in my rush to get home I plugged in a new 2960 stack and did a little bit of very basic configuration, but no passwords were set. I tried to telnet in and the message says that a password is required, but none is set. I tried the SDM as I hadn't turned it off yet and it is prompting me for a user/pass but I have no idea what to put in there. No console is available, it's a new office so no employees around either.
View 14 Replies
View Related
Oct 24, 2012
i am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies
View Related
Mar 30, 2013
Configuration details: I have 2 nexus 5K switches and both 5K is connected to four 2960 access switches in each floor through fiber(shown in the attached picture). I have configured each VPC for each floor and portchannel configuration on 2960s switch to communicate to 5K switches. Now I am not able to communicate PC 1 connected in 1st floor to PC2 connected in 4th Floor.
I have attached topology map of my infra and the configuration files also. 1st floor switch and 4th floor swich have same configuration except IP address and switch name.
View 3 Replies
View Related
Mar 2, 2012
If I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies
View Related
Jan 30, 2012
Document at url... is quite interesting,One of these goes about the behavior of a switch (2960-S and 3750G) when QoS is not enabled vs the one when QoS is simply enabled with "mls qos".What additional commands, beside "mls qos", would be needed so as to simulate as accurately as possible the switch's behavior when QoS is not enabled?
View 3 Replies
View Related
Nov 13, 2011
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
View 11 Replies
View Related
Sep 4, 2012
I have a Cisco 2960-S Switch, It is connected to a jack in the building to check the settings, Interface VLAN 1 has an ip, there is a default gateway, Any host connected to switch can access the network resources. But the problem is that I have to use Serial Cable to configure it. I cant ping or telnet into it from any other device. PC's are on different subnets/VLANS.
Basically this switch is connected to a port in a different switch, Do i have to make a trunk?
View 8 Replies
View Related
May 5, 2013
I have a 2960 that bounced several times over the weekend and then appears to have lost its configuration. Using CDP from the backbone switch pulls up the information below. Is there any way for me to configure the downed switch from another switch on the network? I am trying to avoid having someone from the site try to find a console cable and a suitable computer with a serial port. [code]
View 2 Replies
View Related
Oct 21, 2011
I did the DHCP configuration for my CISCO 2960 switch but the clients are still not able to get the IPs.see the configuration below.
(config)#ip dhcp database cisco.com
(config)#pool test
(config-if)#client client-id vlan 500
(config-if)#ip dhcp snooping trust
View 1 Replies
View Related
Jan 8, 2013
I am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
View 14 Replies
View Related
Sep 3, 2012
I am working on Multicast scenario, There is one 6513E switch one 2960 switch. Two VRF's are configured in core switch (6513) IPTV-SRV and Villa-VRF IPTV-SRV vrf has IPTV server and Villa-VRF has IPTV i.e. client.
V LAN 30 is mapped to IPTV-SRV vrf with subnet address 192.168.30.0/24
V LAN 12 is mapped to Villa-VRF with sub net address 192.168.12.0/24
I did the following configuration for VRF but its not working . i am not an expert in multicast design but seems i did most of the configs.
ip vrf IPTV-SRV
rd 30:1
mdt default 232.1.1.1
route-target export 30:1
route-target import 10:1
[code]...
View 3 Replies
View Related
