Cisco Switching/Routing :: 2960-S - Can't Telnet / Ping Into Switch
Sep 4, 2012
I have a Cisco 2960-S Switch, It is connected to a jack in the building to check the settings, Interface VLAN 1 has an ip, there is a default gateway, Any host connected to switch can access the network resources. But the problem is that I have to use Serial Cable to configure it. I cant ping or telnet into it from any other device. PC's are on different subnets/VLANS.
Basically this switch is connected to a port in a different switch, Do i have to make a trunk?
View 8 Replies
ADVERTISEMENT
Sep 17, 2012
I have 2 switches. 2960 and 3750. I have trunk on both ports of the switch. there are couple of vlans and ports are assigned to those vlans. examples are management, voice and data. int vlan 1 has ip there is default gateway the hosts are able to connect to the internet when connected to the switch.
View 5 Replies
View Related
Apr 10, 2012
We got a switch issue here for 4507R-E with two sup6l-e supervisor running sso redudant. and we found that sometimes client can't ping through the local vlan ip add on the switch , can't logon the cli by telnet too. In the direct connected network device such as access switch and ASA , can't ping or telnet the 4507R too. when we made a forceswitch to sso standby supervisor from console , the problem solve and everything get fine . after that, we switch angin back to the origin supervisor , fine too.
before we made the supervisor forceswitch , we had check the system cpu usage is 15 - 20 % from console . also we had creat a new vlan 200, attach the notebook to 4507's vlan 200 port , the notebook can't ping or telnet the vlan 200 ip interface too.
View 1 Replies
View Related
May 1, 2013
i have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
View 14 Replies
View Related
Feb 7, 2012
The network is set up like this.
Host -----> 3750 (classic) running IPSERVICES stack ----> 3550 router -----> VPN 3005 Concentrator.
IP routing is disabled on the 3750 (it's acting solely as a switch) IP routing is enabled with an EIGRP process running on the 3550 router that has the network for the 3005 broadcasting.
I can ping the vpn 3005 concentrator from a telnet session in the 3550 but not from the 3750.I can ping between the 3750 and the 3550 vlan management interfaces. Visually speaking it's like this
3750 ------> 3550 [Success!!!!]
3550 ------> VPN 3005 Concentrator [Success!!!!]
3750 ------> 3550 --xxxx--> VPN 3005 Concentrator [Timeout....]
I know this because I tracerout to the 3005 from the 3750 and it resolved the default gateway configured for the 3550 properly but then started timing out.
The 3750 is trunked to the 3550.
3750 is vtp client mode
3550 is vtp server mode
I'm wondering if there's a layer 2 issue involved here as it is a VTP domain and maybe it's not returning properly.
View 2 Replies
View Related
Mar 4, 2012
I have set up a newly switch, cisco 3570C. Its in v15 and the only configuration i did is:
-set up interface ip add. 10.132.16.111
-set up telnet
I am able to telnet within LAN environment. I cant ping or telnet the switch in a WAN enviornment. Is there any setting i should confgure on the switch?
View 12 Replies
View Related
Apr 12, 2012
I only want SSH to be allowed when accessing this switch, but telnet is still allowed, why? Whe authenticate via radius.version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname 3750!boot-start-markerboot-end-marker!logging buffered 64000logging console informationallogging monitor informationalenable secret 5 $1$1K$!username admin privilege 15 secret 5 $1$Bs$cLHusername users view priv3 secret 5 $1$Jfnviwp!!aaa new-model!!aaa authentication login default group radius localaaa authentication enable default lineaaa authorization consoleaaa authorization exec default group radius local !!!aaa session-id commonclock timezone GMT 0clock summer-time BST recurring last Sun Mar 2:00 last Sun Oct 3:00switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-12ssystem mtu routing 1500udld aggressiveno ip domain-lookupip domain-name CB!!login on-failure loglogin on-success log!!crypto pki trustpoint TP-self-signed-3817403392enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-3817403392revocation-check nonersakeypair TP-self-signed-3817403392!!crypto pki certificate chain TP-self-signed-3817403392certificate self-signed 01 3082024C 308201B5 A0030201 02020101 300D0609 2A864886 F70D0101 04050030 31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274 69666963 6174652D 33383137 34303333 3932301E 170D3132 30343133 31303539 33395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649 4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 38313734 30333339 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100C31D AE6DD8B5 56245317 AD96F4F4 727385D4 97A5B138 488A215E 4294FC40 1C5B2F26 2B75E1CF E562F240 118F2F50 0CFF2449 16EC66EA 2D489F5F F36BFD05 ACCC79CA DDDA984D 4CB7AB DD95A5E0 9274A225 3F5A3634 DEBF1A2A 416E2189 B35B4473 C7D5EE2C E3D41675 A86F31CD.
View 3 Replies
View Related
Feb 9, 2012
I can't to connect on my switch (WS-C2950G-48-EI) with Telnet or HTTP.When to connect with console, i have a error [code]
View 4 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
Feb 5, 2013
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
View 5 Replies
View Related
Dec 12, 2006
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies
View Related
Jan 14, 2013
I am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies
View Related
Aug 20, 2012
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
View 3 Replies
View Related
Apr 29, 2012
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
View 5 Replies
View Related
Jan 24, 2012
I am setting up a new 2960-S switch and none of the recommended username and passwords combinations work. I have tried CIsco Cisco, <blank> cisco and various other permutations.
I have tried to reset the switch to factory defaults and it still doesn't work. The switch is currently connected to a 3560G and has been assigned an IP. If I try to access it from Network assistant it shows as unmanaged and I get prompted for a username and password.The switch is connected to another new 2960-S via a FlowStack module.
View 4 Replies
View Related
Nov 28, 2012
I need to know the 172cisco 1 router support to IPv6 & it support to IPv6 then which IOS is required for it.Also I need to know the cisco 2960 switch is support to IPv6?
View 3 Replies
View Related
Feb 19, 2013
Currently Being Moderated password recovery
View 3 Replies
View Related
Feb 16, 2012
I am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
View 4 Replies
View Related
Feb 9, 2012
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
View 5 Replies
View Related
Oct 22, 2012
I have a Cisco 1841 router connected to a Cisco 2960 switch.Users behind the router can't access the internet but when someone is directly connected to the switch with his PC and uses the IP Address found on the WAN port of the router, he's able to go on to the internet. [code]
View 4 Replies
View Related
Mar 8, 2012
Today in my rush to get home I plugged in a new 2960 stack and did a little bit of very basic configuration, but no passwords were set. I tried to telnet in and the message says that a password is required, but none is set. I tried the SDM as I hadn't turned it off yet and it is prompting me for a user/pass but I have no idea what to put in there. No console is available, it's a new office so no employees around either.
View 14 Replies
View Related
Oct 24, 2012
i am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies
View Related
Mar 30, 2013
Configuration details: I have 2 nexus 5K switches and both 5K is connected to four 2960 access switches in each floor through fiber(shown in the attached picture). I have configured each VPC for each floor and portchannel configuration on 2960s switch to communicate to 5K switches. Now I am not able to communicate PC 1 connected in 1st floor to PC2 connected in 4th Floor.
I have attached topology map of my infra and the configuration files also. 1st floor switch and 4th floor swich have same configuration except IP address and switch name.
View 3 Replies
View Related
Mar 2, 2012
If I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies
View Related
Jan 30, 2012
Document at url... is quite interesting,One of these goes about the behavior of a switch (2960-S and 3750G) when QoS is not enabled vs the one when QoS is simply enabled with "mls qos".What additional commands, beside "mls qos", would be needed so as to simulate as accurately as possible the switch's behavior when QoS is not enabled?
View 3 Replies
View Related
Nov 13, 2011
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
View 11 Replies
View Related
May 5, 2013
I have a 2960 that bounced several times over the weekend and then appears to have lost its configuration. Using CDP from the backbone switch pulls up the information below. Is there any way for me to configure the downed switch from another switch on the network? I am trying to avoid having someone from the site try to find a console cable and a suitable computer with a serial port. [code]
View 2 Replies
View Related
Oct 21, 2011
I did the DHCP configuration for my CISCO 2960 switch but the clients are still not able to get the IPs.see the configuration below.
(config)#ip dhcp database cisco.com
(config)#pool test
(config-if)#client client-id vlan 500
(config-if)#ip dhcp snooping trust
View 1 Replies
View Related
Jan 8, 2013
I am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
View 14 Replies
View Related
Feb 4, 2013
I have a 2960 switch and every then and now the ports are flapping, while i was on console i saw ports going down and coming up...when the ping to machine ip addresses timed out the port status on switch was still up...no errors collisions seen on sw port. Below is sh int when the port was flapping
[code]...
View 1 Replies
View Related
Sep 3, 2012
I am working on Multicast scenario, There is one 6513E switch one 2960 switch. Two VRF's are configured in core switch (6513) IPTV-SRV and Villa-VRF IPTV-SRV vrf has IPTV server and Villa-VRF has IPTV i.e. client.
V LAN 30 is mapped to IPTV-SRV vrf with subnet address 192.168.30.0/24
V LAN 12 is mapped to Villa-VRF with sub net address 192.168.12.0/24
I did the following configuration for VRF but its not working . i am not an expert in multicast design but seems i did most of the configs.
ip vrf IPTV-SRV
rd 30:1
mdt default 232.1.1.1
route-target export 30:1
route-target import 10:1
[code]...
View 3 Replies
View Related
