Cisco Switching/Routing :: 7604 WS-X6724-SFP - Can Apply Service Policy To Dot1q Main Port
Jul 9, 2012
Example config
int g2/24
service-policy output test
#and/OR
int g2/24.10
encap dot1q 10
ip address 10.1.1.1 255.255.255.0
service-policy output test
View 5 Replies
ADVERTISEMENT
Mar 21, 2013
I got this 3640, trying to apply a service-policy (output and input), but seems like I do it something wrong...because he only apply the output policy... here the config, I already try to config the service police inside the fa0/0, but is not showed at all, he only show the output, its like I never apply that
View 1 Replies
View Related
Jul 18, 2011
I've run a across a strange issue that I've not encountered before and after the things I've tried am beginning to think it's a limitation of the router itself. What I have are 3 Cisco 1941 routers that are all endpoints for a customer's MPLS network. STL is the headquarters and both remote offices have a link back this router. Each of the remote locations only have 1 serial interface. It is a flat network with few routes and a small shoretel voip system running across it. Each router is running C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2).
QoS is configured as follows on each router:
class-map match-any AutoQoS-VoIP-Remark
match ip dscp ef
match ip dscp cs3
match ip dscp af31
class-map match-any AutoQoS-VoIP-Control-UnTrust
match access-group name AutoQoS-VoIP-Control
class-map match-any AutoQoS-VoIP-RTP-UnTrust
[code]....
If I try to apply the policy map to serial0/0/0, I get the following error:
% policy map utoQos-Policy-Untrust not configured
I've tried to create a different policy map with the same settings and get the same error. We thought that when it was first set up, each interface belonged to the same network, so we separated things out (hence the .252 mask). I'm not sure what else to try and I'm hoping its something painfully simple that I'm missing.
View 2 Replies
View Related
Jan 24, 2013
We are planning to implement the following policy map for egress traffic on an Nexus 7000:
policy-map type queuing dd-1p3q1t-8e-out-10G class type queuing 1p3q1t-8e-out-pq1 priority level 1 shape percent 10 class type queuing 1p3q1t-8e-out-q2 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q3 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q-default bandwidth remaining percent 90
We are using two N7K's to which is one N5K connected through a vPC. From the N5k we use a port-channel with 4 * 10G. Two of this four ports are connected to on N7K and the other two are connected to the other N7K. On the n/K's we are using vPC.
My question now are:
1. Where i have to connect the policy map? To the port-channel or on each physical interface?
2. When i have to connect this policy to the port-channel, how does i have to set the shape percent, when i would like to reserve 10% from the 40G? Does i have to set the shape value to 5% on each N7K because vPC?
View 1 Replies
View Related
Mar 11, 2012
I am having a problem with PBR done on a 7604-S router - It seems like it is not done in harware. I have an Iperf client and an Iperf server, and would like to test the performance of 7600 router for PBR, supervisor is RSP720-3C-G and used interface card is 7600-ES20-GE3C ESM20G.
I have read numerous discussions about PBR that is supposed to happen in hardware when you use it with matching access-list and set ip next-hop.Although, when I start the iperf, the 7600 cpu is hitting the 80-90 % boundary, and transfer bandwidth can't go over 120-130 Mbit/s.The IP Policy is applied on an interface part of vrf ONE maybe this is casing the problem... ?
The diagram and configuration follows:
Configuration:
c7604#sh run
boot system flash disk0:c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin
!
ip vrf one
[Code]...
View 8 Replies
View Related
Apr 22, 2012
Here is my configuration below , i have upgraded my C-3750 switch IOS from IPbase to IPservices , after upgrading i have tried to apply PBR on my Vlan 4 and failed , when i am tying to apply route-map to Vlan4 the command was taking but i am unable to see the route-map when sh run , i am giving the command as "ip policy route-map TTSL" in my Vlan4 , below is the configuration.
In Vlan2 i have connected one ISP and Vlan4 I have connected one ISP , my local subnets are 192.168.1.x and 192.168.2.x , now i want to route the 192.168.1.x traffic from Vlan2 and 192.168.2.x Traffic from Vlan4 .
sh boot
coreswitch#sh boot
BOOT path-list : flash:c3750-ipservices-mz.122-35.SE5/c3750-ipservices-mz.122-35.SE5.bin
[Code].....
View 9 Replies
View Related
Nov 2, 2011
I would like to know why i can't configure to 100 full duplex one port from target follow: WS-X6724-SFP
View 2 Replies
View Related
Feb 16, 2012
I am facing problem with ACE configuration. I want to redirect 443 traffic to my Proxy Server. But I am not able to do this. I want to redirect only subnet 192.168.80.0/24..Then only it is working but I dont have to have this policy to be applied on all the users only one subnet I want to have under HTTPS policy.
how can I apply the policy only on specific subnet so that port 443 traffic can be redirect and rest of all subnets can go direclty to Internet.
View 8 Replies
View Related
Nov 10, 2011
I have some trouble with that policy-map on my 2960 or 3560 switches with LAN base 12.2(53)SE2. I want to use that feature to catch video traffic from webcams in laptops which can't send dscp values out of the box. This is my test config to check if the function is working: catch every traffic from my workstation for testing, access-list 101 permit ip any any, class-map match-all CL_TEST
1. I can't see any counters with the command "sh policy-map interface FastEthernet 0/1". Cisco tells that this command is not possible. But how I can see if the policy is working correct?
2. When I did the configuration I can't see any packets with dscp af41 on the out going interface on the switch with "sh mls qos int gi0/1 statistic" as I expected. After reloading the switch I see the pakets with af41. Okay for that moment. But.After that I changed something in the policy-map. Only "set ip dscp ef" for a second test.
Generating some traffic I see only packets with af41 as before I changed the policy-map. No traffic with ef on the outgoing interface.
View 4 Replies
View Related
Jun 2, 2013
i just configured a C6K VSS with Sup2T, 15.1SY IOS software and a WS6724-SFP module with the follwing cos config:
auto qos default
table-map cos-discard-class-map
map from 0 to 0
map from 1 to 8
map from 2 to 16
[code]....
After applying the service policy to one interfac of the WS6724-SFP module the policy is deployed to all interfaces of the module. So far it should be ok but after a short time all interface of the module begin to go down an up and down and up ... flapping.
View 1 Replies
View Related
Dec 24, 2012
i would like to know the possibility to use mls qos trust dscp with service-policy in the IOS ver.12.2(25)SEE2.The specific version is not possible to configure like below.
Cat3750(config-if)#do sh run int f1/0/1
Building configuration...
[code]....
View 8 Replies
View Related
Jan 26, 2009
I have a 3750 switch (c3750-ipbasek9-mz.122-46.SE.bin) were i want to add bandwitdh limit pr. interface, doing the following:
ip access-list extended customer_A
permit ip any any
class-map match-all BW_10Mbps
[Code]....
When i trie to apply the "service-policy output 10 Mbps" to the interface, it says the service-policy output is not supported on the switch. Is this a software related isue ?
View 4 Replies
View Related
Jan 6, 2013
interface Vlan24
description Internal Wireless Internet
ip address 10.x.0.1 255.255.254.0
[Code]....
So, I am trying to limit the bandwidth used by this vlan. The service-policy output statement works, the service-policy input statement does not. My test is to get on that vlan and go to speedtest.net. My download speeds are about 3.5Mb/s, my upload speeds are about 20Mb/s.
it has something to do with this:
sh mls qos ip
QoS Summary [IPv4]: (* - shared aggregates, Mod - switch module Sid - Switch Id)
Int Sid Mod Dir Class-map DSCP Agg Trust Fl AgForward-By AgPoliced-By
[Code].....
View 1 Replies
View Related
Sep 15, 2011
I have a 4510R-E chassis with SUP7-E running IOS XE version 3.01.01.SG. I am unable to create a port-channel and apply auto-qos for VOIP.If I configure auto-qos on the physical interfaces, I get this message when I try adding them to the port channel:
"The attached policymap is not suitable for member either due to non-queuing actions or due to type of classmap filters."
Auto-qos is not an available command in the port-channel interface configuration, but if I try adding the service policies that were created by auto-qos to the port channel manually, it lets me apply the input policy but on the output policy I get this message:
"A service-policy with queuing actions can be attached in output direction only on physical ports."
With the input policy applied to the port-channel interface, I tried addign the output policy to the physical ports and I got this message:
"A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port."
Is there a way to get the auot-qos policies applied to the port-channel properly?
View 3 Replies
View Related
Feb 3, 2013
We have a 7609 in production network and I am trying to find out the SFP vendor plugged in module WS-X6724-SFP."show inventory raw" gives me the SN but not the vendor name. "show hw-module subslot 1/1" shows The indicated slot/subslot number is empty. Any commands which can show the SFP vendor?
View 1 Replies
View Related
Nov 20, 2011
I'm adding another module, WS-X6724-SFP, to our C6506E core switches. I read that it is hot swappable.
View 1 Replies
View Related
Sep 20, 2012
The line card WS-X6724-SFP inserted in slot 2 is getting MINOR ERROR. I could also see TestTransceiverIntegrity: on port no 2/11 has failed.
Is this a h/w issue?
==================================================================================================
S/w model : WS-C6509-E
IOS : s72033-adventerprisek9_wan-mz.122-33.SXI3.bin
==================================================================================================
1) TestTransceiverIntegrity:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . F . . . . . . . . . . . U .
View 2 Replies
View Related
Jul 17, 2012
When quoting a WS-X6724-SFP line card for a Catalyst 6500:
1. If no Distributed Forwarding Card 3 (DFC3) is selected, can it be purchased at a later time as a spare part or the client needs to buy the line card with the DFC3 included from start?
2. Does each line card require a DFC3 in order to be able to perform localized forwarding decisions?
3. Does the DFC3 card is embedded in the line card physically?
View 4 Replies
View Related
May 15, 2012
I would like to know if it possible to create a policy map in order to redirect the traffic ( 80 , http, 8080) to a proxy.
My current equipment its a 3750X using a IP Service License ,I was reviewing some options but i want to be sure before implement in production.
View 8 Replies
View Related
Feb 28, 2012
We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.
View 10 Replies
View Related
Jun 4, 2013
we have a nat exemption rule for 10.0.0.0/8 to w.x.y.z followed by some static nat rules and then dynamic policy nat rule for 10.0.0.0/8 to w.x.y.z natting to IP a.b.c.d.When I do a packet trace from 10.10.10.10 to w.x.y.z, it shows the packet first matching against the nat exemption rule, and then immediately afterwards it matches the dynamic policy NAT rule. The static nat rules are being successfully bypassed (which is what I want), but why does the dynamic policy nat rule apply if an exempt rule has been hit already? An actual test between the IPs above reflects the result of the packet tracer as well (IP a.b.c.d is seen on server w.x.y.z).We are running the following software on an ASA5520.
View 7 Replies
View Related
May 1, 2013
I have a 3560G that I cannot apply a policy route-map to one of the VLAN interfaces. I am running up to date software, c3560-ipservicesk9-mz.150-2.SE2 and it accepts the command, but does not show it in the sh run of the interface. I updated to this code as I had seen previously someone said it needed to be version 15 before you could apply route-maps to VLAN interfaces.
View 4 Replies
View Related
May 19, 2011
Unfortunately it's not particularly obvious as the error that's thrown when trying to apply an IPv6 access-list to a DAP policy is pretty vague:
View 2 Replies
View Related
Apr 2, 2012
Is it possible to do dot1q-tunneling on the new Cisco Calalyst 2960 Compact series switches? I know that the 3560 series support it, but im unable to find any information about the 2960C series, personally i doubt it as the standard 2960 series don't support it.
View 2 Replies
View Related
Mar 14, 2013
i'm desperately trying to get LACP working over a dot1q Tunnel. The "Service Provider" Switches are two 4506-E Switches with SUP7-E connected via a 10G Link, running on cat4500e-universalk9.SPA.03.03.00.SG.151-1.SG
sample config:
dot1q tag vlan native
interface GigabitEthernet3/1
switchport access vlan 2001
[Code].....
View 4 Replies
View Related
Nov 9, 2011
If you have a router with multiple direct vanilla FE (non trunked) interfaces on a switch trying to send QOS tagged packets to a wifi bridge several switches away does the trunking in the switched infrastructure mess with the qos tags if no qos is configured on the switches.
Does it depend on the switch? We have new 2960's running 12.2 and a few older 2950's running 12.1
View 1 Replies
View Related
Jan 26, 2012
enable dot1q encapsulation on two ethernet ports on a 1721 router. I am able to configure it on the built in fastethernet port, but not on any interface provided by a WIC-1ENET or a WIC-4ESW. I have an application that requires two physical ethernet ports that support dot1q encapsulation.
View 4 Replies
View Related
Jun 3, 2011
We are trying to apply specific service policies per PPPOE-User.
Our BRAS is a Cisco 7206VXR , running c7200-spservicesk9-mz.122-33.SRE3.bin
When we try an very easy service policy as following the policy is well applied:
Code...
View 0 Replies
View Related
Jul 9, 2012
i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
[Code]......
View 2 Replies
View Related
Jul 17, 2012
I have a Catalyst 4500 L3 Switch Software (cat4500e UNIVERSAL-M), Version 03.02.00.XO RELEASE SOFTWARE (fc2). So I just wanted to verify that the switch only does dot1q encapsulation because the switchport trunk encapsulation dot1q command does not work.
View 3 Replies
View Related
Nov 20, 2011
In fact i receive traffic on a one client per vlan basis (traffic is PPPoE), i receive all this traffic on a router, collecting all these vlan on a bridge where the pppoe packets are treated.When I use a transeiver to convert operator fiber arrival to my router copper media interface, i have no problem....
When I use dot1q-tunnel to make the same on my 3750, packets seems to be corrupted.I get PPPoE timeouts and packet loss, not regulary, totally stochastic...
I made dozen of tests and different settings, without success I first thougt of MTU issues. [code] I made tests with system MTU and/or system jumbo MTU above 1500, without success.I didn't found any known caveats on 3750 running Version 12.2(25r)SEE4 related to dot1q-tunnel.
View 7 Replies
View Related
Jul 14, 2012
i read alot about password recovery , but when i apply it to cisco 7604 it fails ?i went to rommon mode and typed# confreg 0x2142 then i typed reset when the router startup it request a password form me ,i can enter the user mode , and when i type sh ver command i note that the config resgitser is 0x2102 , not 0x2142 !!!!
i could enter the privilage mode !!!! and seems no thing changed ! does this router has a specific password recovery procedure ? which differes than the classic procedure?
View 4 Replies
View Related
Sep 2, 2012
I was called into a company today to look at their Cisco 7604 router as it had stopped working. The supervisor has all it LED in orange state, there was no blinking of the lights at power on they went straight to orange. Tried removing all cards, having only supervisor card in, etc but always the orange lights.
View 2 Replies
View Related