Cisco Switching/Routing :: Installing WS-X6724-SFP Hot Swap?
Nov 20, 2011I'm adding another module, WS-X6724-SFP, to our C6506E core switches. I read that it is hot swappable.
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: WS-X6724-SFP / How To Find Out SFP Vendor
Feb 3, 2013We have a 7609 in production network and I am trying to find out the SFP vendor plugged in module WS-X6724-SFP."show inventory raw" gives me the SN but not the vendor name. "show hw-module subslot 1/1" shows The indicated slot/subslot number is empty. Any commands which can show the SFP vendor?
View 1 Replies View RelatedCisco Switching/Routing :: WS-X6724-SFP - Getting Minor Error
Sep 20, 2012The line card WS-X6724-SFP inserted in slot 2 is getting MINOR ERROR. I could also see TestTransceiverIntegrity: on port no 2/11 has failed.
Is this a h/w issue?
==================================================================================================
S/w model : WS-C6509-E
IOS : s72033-adventerprisek9_wan-mz.122-33.SXI3.bin
==================================================================================================
1) TestTransceiverIntegrity:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . F . . . . . . . . . . . U .
Cisco Switching/Routing :: DFC3 For WS-X6724-SFP 6500 Line-cards?
Jul 17, 2012When quoting a WS-X6724-SFP line card for a Catalyst 6500:
1. If no Distributed Forwarding Card 3 (DFC3) is selected, can it be purchased at a later time as a spare part or the client needs to buy the line card with the DFC3 included from start?
2. Does each line card require a DFC3 in order to be able to perform localized forwarding decisions?
3. Does the DFC3 card is embedded in the line card physically?
Cisco Switching/Routing :: Can't Configure To 100 Full Duplex One Port From Target WS-X6724-SFP
Nov 2, 2011I would like to know why i can't configure to 100 full duplex one port from target follow: WS-X6724-SFP
View 2 Replies View RelatedCisco Switching/Routing :: 7604 WS-X6724-SFP - Can Apply Service Policy To Dot1q Main Port
Jul 9, 2012Example config
int g2/24
service-policy output test
#and/OR
int g2/24.10
encap dot1q 10
ip address 10.1.1.1 255.255.255.0
service-policy output test
Cisco Switching/Routing :: Shutdown 4507r-e And Just Swap Out Blade?
Apr 2, 2012If i replace a card of the same type in the same slot will I lose the configuration for that card or does it live in the backplane of the device?Is there any special command I need to run to replace the card or can i shutdown the 4507r-e and just swap out the blade?
View 3 Replies View RelatedCisco Switching/Routing :: C3560 Swap Out Not Ping Across Network
Jun 17, 2012Had a switch die over the weekend, a c3560, per our normal procedure I pulled the hardware put a very basic config on it(vlans, portchannel, uplink ports, ip of management vlan, con and vty security, snmp, enable secret, and hostname). Then I use solarwinds orion to upload a copy of the old config to bring the switch back to the same state as the one that failed. Its a system that has worked for us 3 or 4 times in the past. But this time when the base config was on the box it couldnt ping across the network.I have tried clearing the arp cache and the dynamic mac tables, i verified the routing tables and even removed the 10.1.185.128/27 route and re-added it, saw the routing update go across to the other 65k, tried bouncing the edge switch(i cant bounce the 65k's), took down the po between the edge and 65k.
View 2 Replies View RelatedCisco Switching/Routing :: Swap With Backup Switch WS-2950T
Jan 8, 2013my 2970 having intermittent problem. i would like to swap with my backup switch WS-2950T. when i try to configure the 2950 following the 2970 config, i unable to perform this command "switchport trunk encapsulation dot1q". does 2950T does not support this command??
View 8 Replies View RelatedCisco Switching/Routing :: 4506 Hot Swap 100M Card With Gig Module
Oct 18, 2012If you hot swap a 100M card with a Gig module in a live 4500 switch, what happens to the running-config? Don't have the module versions to hand.
View 2 Replies View RelatedCisco Switching/Routing :: Installing SDM 2.5 On 2600?
Sep 17, 2012I am trying to configure SDM 2.5 on a cisco 2600.I have access via telnet to the router and was able to change the enable password - which i think is level 15 (right?) and setup (and bring up) the ip on the ethernet interface. I can ping - and get response from - the router Trying to install SDM on the router i need to provide the default username i tried both admin/administrator but SDM can't communicate with the router?
View 21 Replies View RelatedCisco Switching/Routing :: Installing Ios On 3550?
Jan 17, 2013im trying to install a ios 12.2v on my switch. when the screen prompt it does not show me the user move symbol " SW1> ". all i see is " SW:" and from there i can not enter the commands to download from tftp server !
View 7 Replies View RelatedCisco Switching/Routing :: 6509E - Installing And Setting Up Second Sup720
Feb 27, 2013Trying to find documentation on the proper procedure for installing a second sup720 into our 6509-E chassis for sup redundancy. I have found documents that tout how 'cool' and 'awesome' NSF/SSO, and all that is, but haven't found any docs on installing a second sup720 into a chassis that is currently in production and is only running one sup720. In all the years that this chassis has been out, there must me a documented procedure out here to explain this.I have been through the following pages, and have found nothing to this effect.
View 1 Replies View RelatedCisco Switching/Routing :: X6748 And NAM-2 Modules Inaccessible After Installing Linecard
Oct 8, 2012I've installed second WS-X6748-SFP linecard on my catalyst 6509 with sup720-3b and after that NAM-2 and IDSM-2 module become inaccessible from management network. I can only login with session slot N proc 1.When I execute #hw-module module 4 reset, modules become accessible.
#sh module from cat6509
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL114670XW
3 48 48-port 100FX SFP Ethernet Module WS-X6148-FE-SFP SAL1201BZKF
4 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL1625ETFJ
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1206FNGQ
6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL1206FVFB
8 8 Intrusion Detection System WS-SVC-IDSM-2 SAD120502LR
9 8 Network Analysis Module WS-SVC-NAM-2 SAD120206LB
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 001e.4a3e.3b30 to 001e.4a3e.3b5f 1.10 12.2(14r)S5 12.2(18)SXF1 Ok
3 001e.4aea.e7b0 to 001e.4aea.e7df 3.3 8.4(1) 8.5(0.46)RFW Ok
4 5057.a895.bb84 to 5057.a895.bbb3 2.4 12.2(18r)S1 12.2(18)SXF1 Ok
5 001c.58d0.6dc4 to 001c.58d0.6dc7 5.6 8.5(2) 12.2(18)SXF1 Ok
6 0016.c848.3698 to 0016.c848.369b 5.6 8.5(2) 12.2(18)SXF1 Ok
8 001e.f7a1.54b0 to 001e.f7a1.54b7 6.3 7.2(1) 7.0(8)E4 Ok
9 001e.f72a.ba62 to 001e.f72a.ba69 4.3 7.2(1) 5.1(2) Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Centralized Forwarding Card WS-F6700-CFC SAL114881B6 4.0 Ok
4 Centralized Forwarding Card WS-F6700-CFC SAL1624EGQS 4.1 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B SAL1206FNZY 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL1206FSFH 3.1 Ok
6 Policy Feature Card 3 WS-F6K-PFC3B SAL1206FP27 2.3 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL1206FN26 3.1 Ok
8 IDS 2 accelerator board WS-SVC-IDSUPG ADBG7270048 2.5 Ok
cat6500 running 12.2(18)SXF12a ios...
Cisco Switching/Routing :: Nexus 5548 Rebooting Continually After Installing L3 Base License
Jul 30, 2012we recently purchased L3 daughter cards (N55-D160L3-V2) for our 5548UPs along with the LAN Enterprise Services licenses (N55-LAN1K9).
I installed the cards and Ent Svcs lic this past weekend and everything went well excep that I couldn't enable the EIGRP feature .. apparently EIGRP requires the LAN Base (N55-BAS1K9-BUN) license even when you have the Enterprise lic installed, so I was able to dig up that license eventually (which comes with the L3 daughter card, incidentally). Another side effect of not installing the Lan Base lic is that the L3 card/module will be in an "offline" state until the Lan Base lic is installed. Either way, everything was working normally in L2 mode at this time.
So, here I was thinking I was ready to proceed with enabling L3 - this morning I installed the LAN Base license on one of the 5548s which apparently triggered the L3 Daughter card module to go active and triggered a switch reboot. Ok, not that big of a deal, knew that was probably coming. I expected the switch to come back up normally .. NOPE. The switch went into a continual reboot cycle where the console prompt would appear, then about 30 seconds later, would reboot again.
I finally ended up re-installing the original L2 card and the switch came right up. I see that LAN Base and LAN Enterprise are both still installed as well.
What have I done wrong here? Why did the switch go into a continuous reboot cycle once I installed the LAN Base license?
Here are more details :
Software
BIOS: version 3.5.0
loader: version N/A
[Code]....
Cisco Switching/Routing :: 2800 Series Router - Removing And Installing Compact Flash Memory Cards
Nov 15, 2011I just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies View RelatedCisco WAN :: Hot-swap On ASR1000?
Sep 25, 2012The ASR1000 router supports hot-swap modules and network interfaces?
View 1 Replies View RelatedCisco :: How To Swap An Extension Number
Dec 24, 2012I'm working with a Cisco Unified CM 7.0There are sevral ip phones in the place.ach phone has a 3 digit extension tied to it. no matter where on the network that phone is plugged in that phone has the same extension. This is a problem because one phone (extension 134) is damaged and was swapped out with a phone that has extension 102. I want that phone that has extension 102 to have the extension 134 instead.So that is my problem. I must say I am merely a CCNA and I have no idea about this voip stuff. I thought it was a simple log in to the server and make a single change. boy was I wrong. I clicked on call routing, then I clicked on Directory number and I got a list of all the DNs. I then click on extension 102 and 134. I noticed the MAC of the respective phones was in a field titled associated devices. I then dissociated both phones thinking I could just associate the appropriate phones next. as soon as I hit save that entire section disappeared. Now those extension aren't tied to any phone and once more those phones now have no extensions. I am freaking out because I can't undo this. I've clicked on literally every single option inside this server. I am in way over my head. I will include a picture to illestrate what I am talking about.
View 6 Replies View RelatedCisco LAN :: 6509-e Best Way To Swap Out Supervisor Module
Mar 28, 2012We have a 6509-e (WS-C6509-E V04) with (4) (WS-X6148-GE-TX) 48 port modules and a supervisor 32 (WS-SUP32-GE-3B).We purchased a supervisor 720 (WS-SUP720-3B) and (2) (WS-6708-10G-3C) 8 port fiber modules and (1) WS-X6748-GE-TX)48 port module to add to the switch. My question is what is the best way to swap out the supervisor module? Can the SUP720 be added as a standby module so that the config can be transferred? Probably a long shot. Is there anything in this swap that I should be concerned with? The other three modules should be pretty straight forward.
View 4 Replies View RelatedCisco WAN :: 3925 Cannot Swap Hwic Without Reload
Dec 20, 2012I have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View RelatedCisco Infrastructure :: Swap Fan In 3845 While It Is Running?
Oct 4, 2011Can you swap fan in 3845 while it is running?
View 1 Replies View RelatedCisco Firewall :: Swap BootVAR On 5505 Without Affecting Activation Key
May 11, 2013If I could swap around the bootvar on my 5505 without affecting the activation key.this is to learn different NAT on pre and 8.3+ IOS.
# sh bootvar
BOOT variable = disk0:/asa825-26-k8.bin
Current BOOT variable = disk0:/asa825-26-k8.bin
CONFIG_FILE variable =
Current CONFIG_FILE variable =
[code].....
Cisco WAN :: ASR1000 Router Supports Hot-swap Modules And Network Interfaces?
Sep 25, 2012The ASR1000 router supports hot-swap modules and network interfaces?
View 2 Replies View RelatedLinksys Wireless Router :: Swap Hard Drives On The E4200?
Aug 3, 2011Im looking to swap out my older 3.5" drive in an external enclosure for a Seagate - FreeAgent GoFlex Desk 2TB. Can I just drag and drop the 200+gb of files on my current drive to the new Seagate - FreeAgent GoFlex Desk 2TB? Or do I need to re configure the new drive in my web browser.
E4200 media server in .02 firmware
Protocols / Routing :: Installing The Wireless Netgear Router?
Sep 4, 2011I am trying to instal my Netgear router. It is asking for the Preferred DNS name and the alternate DNS name? I got the IP address and the other required fields but I'm not sure about eh DNS thing?
View 2 Replies View RelatedCisco Routing :: 3750x - Installing Single Mode Fiber / Switches Not Connecting?
Oct 22, 2011Prior we only had 62.5u multi mode.I've got 3750x switches and new SM SFP and yellow fiber patch cables. None of my links show connected. No lights and trunk port interfaces show down/down.
Is there a special command you have to do on a port when using SM fiber? Do you think I need cross over fibers?
Also, should I be able to see a laser signal light like MM or is SM a different frequency so it's not as visible as MM?
TEGs80G - Swap Unmanaged Devices With More Expensive Cisco Devices?
Jun 1, 2012Currently my home network is being switched via TrendNet TEGs80G unmanaged gig switches. I have been using them for about a year now with no issues. As my home network becomes more advanced, I recently just added a Cisco ASA5505, I am thinking about swapping those unmanaged devices, 4 of them, to managed. I was looking at the Cisco SG300-10 for upstairs, and a 16 port variant for my main core. These devices do not support full Cisco IOS cli, but they are manageable with a rich feature set nonetheless. My question is, should I swap the unmanaged devices with the more expensive Cisco devices, or just keep what works and save the money until I really need to spend it. As previously stated, my home LAN works just fine as it is, however my WiFi, NTV550s, server and workstations are all on the same network. Probably not the most secure but it is what it is without VLAN support.
View 11 Replies View RelatedCisco Firewall :: 5510 / Swap ASA SSM-10 From Dead Firewall?
Mar 20, 2013I currenty have 2 cisco 5510 firewalls one of the firewals is completly dead but contains a Cisco ASA SSM-10 can i remove this card and just place it into a working unit, will i have any problems doing so.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Installing 5-2-0-26-4.tar.gpg On ACS 5.2?
May 26, 2011Trying to upgrade a pair of ACS servers from 5.2.0.26 base to patch 4. I have tried creating different repositiories that are SFTP, FTP, and Local. The secondary unit(ROTACS2) upgraded fine with no problems the primary(ROTACS) will not, see below.
Cisco Application Deployment Engine OS Release: 1.2ADE-OS Build Version: 1.2.0.182ADE-OS System Architecture: i386
Copyright (c) 2005-2009 by Cisco Systems, Inc.All rights reserved.Hostname: ROTACS
Version information of installed applications---------------------------------------------
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.2.0.26Internal Build ID : B.3075
ROTACS/mpartain#
[code]....
It appears that the GPG key is not vaild on this primary server. The patches are in the repositories and I used the acsrepo repo to install on the ROTACS2 secondary server.I have looked through articles and the only mention is to not use TFTP, which I am not. I have also tried to apply patches 1-3 with the same results.
Cisco :: LMS 4.2 Installing In Other Partition Than C?
May 27, 2012I'm having problems installing LMS 4.2 in other partition. I have two operating system. One on C: Windows 7 Pro and One on D:Windows Server 2008,after installing it on Windows Server 2008, i'm able to access the server using the command net start crmdmgtd; but if i restart my machine it gets and error (blue screen) and says: Could not find ntdll.dll in the dynamic library. NTSerializeboot.
View 1 Replies View RelatedCisco :: Error When Installing LMS 4.2.1?
Jun 6, 2012I built a new Win2k8 server meeting all prereq's. This is a new install of LMS. Right at the beginning of the install process, i get this error and the install halts.
View 2 Replies View RelatedInstalling OS From Another Machine CD-ROM
Jan 25, 2012I want to install a windows operating system in my machine but my machine dont have a CD-ROM. so i want to install an OS from using my another PC(Laptop)'s CD-ROM. So is it possible to install OS into my one machine from another different machine(windows-7) via sharing the drive .
View 4 Replies View RelatedCisco WAN :: Installing New CF In 3845 Router?
Mar 24, 2011I am installing Cisco blank CF upgrades (double the capacity of the CF that came with the router) in Cisco 3845 routers and I cannot get the IOS to load.
Network security requires tftp be disabled, so I am limited to xmodem. Slow, but it works. I know the IOS download is good, because I can load it on the CF that came with the router.
I can install, format and read the new flash. But the download locks up and bombs about 1/3 of the way through.
Note: CF that came with the router was "C" so I used the format flash: command. The new flash reads the same as the old, except that there is no file IOS loaded.
I've never had an issue upgrading an IOS, but this is my first shot at installing on a new CF.