I have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 RepliesThe ASR1000 router supports hot-swap modules and network interfaces?
View 1 Replies View RelatedI'm working with a Cisco Unified CM 7.0There are sevral ip phones in the place.ach phone has a 3 digit extension tied to it. no matter where on the network that phone is plugged in that phone has the same extension. This is a problem because one phone (extension 134) is damaged and was swapped out with a phone that has extension 102. I want that phone that has extension 102 to have the extension 134 instead.So that is my problem. I must say I am merely a CCNA and I have no idea about this voip stuff. I thought it was a simple log in to the server and make a single change. boy was I wrong. I clicked on call routing, then I clicked on Directory number and I got a list of all the DNs. I then click on extension 102 and 134. I noticed the MAC of the respective phones was in a field titled associated devices. I then dissociated both phones thinking I could just associate the appropriate phones next. as soon as I hit save that entire section disappeared. Now those extension aren't tied to any phone and once more those phones now have no extensions. I am freaking out because I can't undo this. I've clicked on literally every single option inside this server. I am in way over my head. I will include a picture to illestrate what I am talking about.
View 6 Replies View RelatedWe have a 6509-e (WS-C6509-E V04) with (4) (WS-X6148-GE-TX) 48 port modules and a supervisor 32 (WS-SUP32-GE-3B).We purchased a supervisor 720 (WS-SUP720-3B) and (2) (WS-6708-10G-3C) 8 port fiber modules and (1) WS-X6748-GE-TX)48 port module to add to the switch. My question is what is the best way to swap out the supervisor module? Can the SUP720 be added as a standby module so that the config can be transferred? Probably a long shot. Is there anything in this swap that I should be concerned with? The other three modules should be pretty straight forward.
View 4 Replies View RelatedCan you swap fan in 3845 while it is running?
View 1 Replies View RelatedI'm adding another module, WS-X6724-SFP, to our C6506E core switches. I read that it is hot swappable.
View 1 Replies View RelatedIf i replace a card of the same type in the same slot will I lose the configuration for that card or does it live in the backplane of the device?Is there any special command I need to run to replace the card or can i shutdown the 4507r-e and just swap out the blade?
View 3 Replies View RelatedIf I could swap around the bootvar on my 5505 without affecting the activation key.this is to learn different NAT on pre and 8.3+ IOS.
# sh bootvar
BOOT variable = disk0:/asa825-26-k8.bin
Current BOOT variable = disk0:/asa825-26-k8.bin
CONFIG_FILE variable =
Current CONFIG_FILE variable =
[code].....
Had a switch die over the weekend, a c3560, per our normal procedure I pulled the hardware put a very basic config on it(vlans, portchannel, uplink ports, ip of management vlan, con and vty security, snmp, enable secret, and hostname). Then I use solarwinds orion to upload a copy of the old config to bring the switch back to the same state as the one that failed. Its a system that has worked for us 3 or 4 times in the past. But this time when the base config was on the box it couldnt ping across the network.I have tried clearing the arp cache and the dynamic mac tables, i verified the routing tables and even removed the 10.1.185.128/27 route and re-added it, saw the routing update go across to the other 65k, tried bouncing the edge switch(i cant bounce the 65k's), took down the po between the edge and 65k.
View 2 Replies View Relatedmy 2970 having intermittent problem. i would like to swap with my backup switch WS-2950T. when i try to configure the 2950 following the 2970 config, i unable to perform this command "switchport trunk encapsulation dot1q". does 2950T does not support this command??
View 8 Replies View RelatedWhat is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedIf you hot swap a 100M card with a Gig module in a live 4500 switch, what happens to the running-config? Don't have the module versions to hand.
View 2 Replies View RelatedThe ASR1000 router supports hot-swap modules and network interfaces?
View 2 Replies View RelatedIm looking to swap out my older 3.5" drive in an external enclosure for a Seagate - FreeAgent GoFlex Desk 2TB. Can I just drag and drop the 200+gb of files on my current drive to the new Seagate - FreeAgent GoFlex Desk 2TB? Or do I need to re configure the new drive in my web browser.
E4200 media server in .02 firmware
I need 3925 router that support BGP as well as IPSEC VPN. is this correct part number i ordered? CISCO3925-SEC/K9. Its always hard to understand Cisco licensing, specially new one. will above package will have router wth ipbasek9+seck9?
View 4 Replies View RelatedI have a new 3925 ISR G2 router with the universal IOS, 256kb flash in CF0, 1gb flash in CF1. When the router boots it prompts to enter initial config. Whether I say yes or no, enter the appropriate info, "write memory", and reload it comes up with a blank config. I've checked the config-register (2142), copied the start up-config to nvram:, flash0:, and flash1: but nothing works.
View 2 Replies View RelatedCurrently my home network is being switched via TrendNet TEGs80G unmanaged gig switches. I have been using them for about a year now with no issues. As my home network becomes more advanced, I recently just added a Cisco ASA5505, I am thinking about swapping those unmanaged devices, 4 of them, to managed. I was looking at the Cisco SG300-10 for upstairs, and a 16 port variant for my main core. These devices do not support full Cisco IOS cli, but they are manageable with a rich feature set nonetheless. My question is, should I swap the unmanaged devices with the more expensive Cisco devices, or just keep what works and save the money until I really need to spend it. As previously stated, my home LAN works just fine as it is, however my WiFi, NTV550s, server and workstations are all on the same network. Probably not the most secure but it is what it is without VLAN support.
View 11 Replies View RelatedIn our project, we had to configure PAGP between catalyst cisco 3110. there is no problem in configuration of PAGP and everythin is ok,and channel is up.but after reload cisco, chanel can not be up and between switches all packet are in loop between 2 switches.in order to solve this probelm I have to shutdown all port and again create chanel for every port.
View 12 Replies View RelatedRouter with 2 RSP RSP720-3C-GE & Image: c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin We are getting the message as
------------------ show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
Show log is attached & we are getting %DHCPD-4-DECLINE_CONFLICT: messages constantly.
I currenty have 2 cisco 5510 firewalls one of the firewals is completly dead but contains a Cisco ASA SSM-10 can i remove this card and just place it into a working unit, will i have any problems doing so.
View 1 Replies View RelatedI have one router 3925 equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
Please find the attached config details.
I have spend half day to look up this question in cisco official web site, but get nothing . Any infomation about vpn performance of 3925 router？Produce : cisco 3925 ( Cisco 3925 Security Bundle w/SEC license PAK )Question is , how much ipsec vpn tunnels can be carried as a vpn server of this bundle ? if more licenses may be bought, how much most tunnels can be held？
View 5 Replies View RelatedI have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
View 5 Replies View Relatedhow to setup natting on a 3925 router.
View 1 Replies View RelatedI have a question regarding the 3925 router. In the past on my old 3660's, in order to add a new line to an ACL, I would have to remove the entire ACL and readd it when adding new ACL lines to the list. Is this required on the 3925's, or is it like the ASA 5520's where you can just add an ACL any 'ol time without having to remove/add the entire ACL list?
View 2 Replies View Relatedwe are configuring a ras on 3925 router with e1 controller. when we connect the e1 controller to pbx we got on pbx a no frame alarm (detailed error is that we have nfas but we do not have cas). what could be the error? do the router need dsp to have a framed e1?
View 1 Replies View RelatedCisco equipment without RTC defaults to "1 Mar 1993" after the reload. Why this date was chosen?
View 3 Replies View RelatedI have two ASA 5540 working in Active/Standby mode. After I've upgraded them to 8.2.3 ver. I have the following issue: once a day presently active device arbitary reloadI have no err in show version and in syslogs:11:15:50 ASA : %ASA-6-302020: Built inbound ICMP connection for faddr 10.10.0.36/512 gaddr 10.0.0.16/0 laddr 1011:15:58 ASA : %ASA-1-104001: (Primary) Switching to ACTIVE - HELLO not heard from mate.
View 4 Replies View Relatedis there any way to reload the current saved (not running) config without a reboot of the firewall?
View 4 Replies View RelatedFrom PEC training - Cisco says to perform a proper ASR 1004 shutdown by executing 'reload' , then wait for bootstrap message to appear, then [before commencement of unpacking of the IOS] turn off the power switch. IS THIS ACCURATE. Anyone have any doc related to the recommended POWER DOWN process on the ASR 1004. We have a UPS cutover coming up and I want to be ready to power down and restart the new ASR 1004s we have - properly.
View 3 Replies View Relatedi said in the title i have forgot my password for my cisco3925 rourtor and how to reset my password
View 3 Replies View Relatedchecked all the recovery doc, however, there is no one specific for 3900 series router
View 2 Replies View RelatedI am trying to set up a redundant OSPF setup and I am seeing behavior I don't quite understand. At the main office I have two routers, a 3825 connected via full DS3 to the MPLS cloud, and a 3925 connected to the Internet for VPN backup.There are nine branches, but I am only going to talk about three. The three branches all connect together as well as having their own MPLS connections to the cloud. They are all 2821 routers with a 4.5 Mbps multilink interface into the cloud (three T1's). One of the branches has a backup IPSec/GRE Internet connection that I want any of them to be able to use in case of an MPLS problem (which there have been many lately, sometimes involving all of them going down at the same time). The connection into MPLS uses Inter-area OSPF with the provider. The Tunnel connection is also using IA OSPF (the main office is area 0 and this cluster of branches are all on area 100).
OSPF seems to be behaving oddly. At the main office, on the 3825 with the "backup" shut off, if I do "show ip route 10.51.0.0" it shows this output: [code]If the metric before was 24, why would it put in a route with a metric of 53 now? What's worse is that the branches all think they should connect over the MPLS and the main office sends everything over the VPN. It works, but I don't really want asymetric routing! I have included some configs as well... those which I consider relevant. I am including a diagram that has more on it than is relevant, but what I referenced is here (and yes, spanning-tree has been properly configured on the red fiber connections with the connection between FEC2960 and Hl2960 blocking, but try to ignore the LAN stuff because this is in a transitional phase right now anyway).