I need 3925 router that support BGP as well as IPSEC VPN. is this correct part number i ordered? CISCO3925-SEC/K9. Its always hard to understand Cisco licensing, specially new one. will above package will have router wth ipbasek9+seck9?
View 4 RepliesI'm looking to utilize one of my 3925's to create a LAN-LAN IPsec VPN tunnel with another site.
I was under the impression that I needed to get a securityk9 license installed and then I would be good to go. I got a temporary 60 day trial license and successfully installed it, but none of the commands that I need to create the tunnel are showing up for me.
I'm trying to use the "crypto isakmp" command, but that is not showing up: Router(config)#crypto ? ca Certification authority key Long term key operations pki Public Key components
Here's my show license:
Index 2 Feature: securityk9
Period left: 633 weeks 4 days
Period Used: 0 minute 0 second
License Type: Evaluation
License State: Active, Not in Use, EULA accepted
License Count: Non-Counted
License Priority: Low
I have a new 3925 ISR G2 router with the universal IOS, 256kb flash in CF0, 1gb flash in CF1. When the router boots it prompts to enter initial config. Whether I say yes or no, enter the appropriate info, "write memory", and reload it comes up with a blank config. I've checked the config-register (2142), copied the start up-config to nvram:, flash0:, and flash1: but nothing works.
View 2 Replies View RelatedI have one router 3925 equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
Please find the attached config details.
I have spend half day to look up this question in cisco official web site, but get nothing . Any infomation about vpn performance of 3925 router？Produce : cisco 3925 ( Cisco 3925 Security Bundle w/SEC license PAK )Question is , how much ipsec vpn tunnels can be carried as a vpn server of this bundle ? if more licenses may be bought, how much most tunnels can be held？
View 5 Replies View RelatedI have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
View 5 Replies View Relatedhow to setup natting on a 3925 router.
View 1 Replies View RelatedI have a question regarding the 3925 router. In the past on my old 3660's, in order to add a new line to an ACL, I would have to remove the entire ACL and readd it when adding new ACL lines to the list. Is this required on the 3925's, or is it like the ASA 5520's where you can just add an ACL any 'ol time without having to remove/add the entire ACL list?
View 2 Replies View Relatedwe are configuring a ras on 3925 router with e1 controller. when we connect the e1 controller to pbx we got on pbx a no frame alarm (detailed error is that we have nfas but we do not have cas). what could be the error? do the router need dsp to have a framed e1?
View 1 Replies View Relatedi said in the title i have forgot my password for my cisco3925 rourtor and how to reset my password
View 3 Replies View Relatedchecked all the recovery doc, however, there is no one specific for 3900 series router
View 2 Replies View RelatedI have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View RelatedI am trying to set up a redundant OSPF setup and I am seeing behavior I don't quite understand. At the main office I have two routers, a 3825 connected via full DS3 to the MPLS cloud, and a 3925 connected to the Internet for VPN backup.There are nine branches, but I am only going to talk about three. The three branches all connect together as well as having their own MPLS connections to the cloud. They are all 2821 routers with a 4.5 Mbps multilink interface into the cloud (three T1's). One of the branches has a backup IPSec/GRE Internet connection that I want any of them to be able to use in case of an MPLS problem (which there have been many lately, sometimes involving all of them going down at the same time). The connection into MPLS uses Inter-area OSPF with the provider. The Tunnel connection is also using IA OSPF (the main office is area 0 and this cluster of branches are all on area 100).
OSPF seems to be behaving oddly. At the main office, on the 3825 with the "backup" shut off, if I do "show ip route 10.51.0.0" it shows this output: [code]If the metric before was 24, why would it put in a route with a metric of 53 now? What's worse is that the branches all think they should connect over the MPLS and the main office sends everything over the VPN. It works, but I don't really want asymetric routing! I have included some configs as well... those which I consider relevant. I am including a diagram that has more on it than is relevant, but what I referenced is here (and yes, spanning-tree has been properly configured on the red fiber connections with the connection between FEC2960 and Hl2960 blocking, but try to ignore the LAN stuff because this is in a transitional phase right now anyway).
I want to connect my clients from the Windows WS to a VPN Tunnel using 3925 router w/o Cisco VPN client. Is there the way to use native IPSec client on Windows XP or Windows 7?
View 1 Replies View RelatedI need to install an ATM module in a 3925 router. I would like to know if this card is that I have to buy with the transceiver(SFP)?
Will use a fiber cable LC LC singlemode fiber optic.
Module: NM-1A-OC3-POM
Transceiver :SFP-OC3-IR1
Monitoring H.323? I've got a 3925 running15.1(3)T with 9 PRI's. Because of our volume, syslogging is not the desired solution. We want something that we can potentially graph over an 8 hour period, so while the RTMT is accurate, either it won't store the data for 8 hours, or we aren't using it correctly (plus, mgmt may want access to the stats/graphs, and we're not keen on granting them access). So far, we've used: [code] None of these seem to accurately portray utilization. cdsp Active Channels seems to get the closest, so perhaps I have to tweak it a little bit, but so far, nothing accurate.
View 3 Replies View RelatedI have a network architecture like the one HERE but with alot more spokes (32). Would my cisco 3925 be able to support so many crypto maps?
View 2 Replies View RelatedRecently fitted 2 3925 routers on a WAN Mulitlink (2 * 2Mb) which has been working reasonably well but have noticed CRC's and intremitteny up/downs on E1 links. This could be due to issues with Microwave links but on checking nothing stands out on these - no errors or traps form radios.
Anyway taing a closer look at E1 lines and had some questions:-
Microwave radios E1 circuits are set to UNFRAMED, router interfaces set to NO-CRC4, didnt think this was the same?
E1 card are VWIC3-2MFT-T1/E1 and also noticed the following:-
no network-clock-participate wic 0(same for 1 and 2), my card are in slot 0 and 1.
I see no slips etc on E1 controllers .
I was wondering if the NM-1HSSI is supported on the cisco 3925. documentation seems to include only till 3800 series but can't find if it's supported or is there an alternative option for 3925.
View 6 Replies View RelatedI have a new Cisco 3925 router. I have 2 network segments 10.0.1.X with net mask 255.255.255.0 and 10.0.2.x woith netmask 255.255.255.0. I have an internet gateway router at 10.0.1.21. I have set GBethernet 0/0 to 10.0.1.1 / 255.255.255.0 and GBethernet 0/1 to 10.0.2.1 / 255.255.255.0. I have set a static route 0.0.0.0 / 0.0.0.0 to 10.0.1.21 for gateway of last resort.
When I setup a workstation on the 10.0.2.X segment at 10.0.2.100 wirh a gateway of 10.0.2.1, I can ping 10.0.2.1 and 10.0.1.1 but can not ping anything else on the 10.0.1.X network or on the internet. When I am connected to the console port on the router I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and any address in the internet but I can not ping 10.0.2.100.
When I am on a network connected to the 10.0.1.x network af 10.0.1.100 I can ping 10.0.1.1 and 10.0.2.1 and 10.0.1.21 and anywhere on the internet but can not ping 10.0.2.100 or any other address on the 10.0.2.x network other than 10.0.2.1. What Do I need to do on the 3925 to get to all address on each segment and to get to the 10.0.1.21 gateway from the 10.0.2.x addresses?
I am using a Cisco 3925 router and attempting to install an EHWIC card with no luck. The card I am trying to install is EHWIC-D-8ESG.
I have powered down the router, inserted the card into the proper slot and my router doesn't seem to recognize the new card. Is there a command I need to enter to enable the card?
What the maximum concurrent users you can have on a Cisco 3925 for :-
1) Site to Site VPN using IPSEC tunnels
2) GRE tunnel sIf I have 90 users on a single GRE tunnel with 50mb Internet pipe using fat clients will this work ?
To have GRE tunnel support in a Cisco3925 do I need any specific license (DATA, SEC, etc) or it is include in the UNIVERSAL IOS?
View 1 Replies View RelatedI have a new 3925 router and it came with 1 VWIC3-4MFT-T1/E1 card installed. I added a 2nd one and although it shows up in inventory, the interfaces do not show up in configuration in any form, interface or controllers. I used to just install a card and it would be recognized, is that no longer supported and is it platform specific or IOS specific?
View 3 Replies View RelatedI tried any type of combination and just couldn't make it works. Only PPTP works well. Whether Apple iOS IPSec VPN is supported or not?
View 11 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedI just receive a new Cisco 3925 with a etherswitch module 24 port :
SM-ES3G-24-P,I successfully boot the switch module and gain access to it.
I found some documentation on CCO but I don't sorted out this small information :,
Switch#sh cdp neig Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone, D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port IDRouter Gig 0/26 143 R S I CISCO3925 Gig 2/0Switch#
The Router is connected to the switch module via a HIMI :
The Cisco enhanced EtherSwitch service modules also provide a physical Gigabit Ethernet serializer/deserializer integrated circuit transceiver (HIMI) interface. In the Cisco 2900 series and Cisco 3900 series routers, the HIMI link on the Cisco enhanced EtherSwitch service modules is connected to the router internal Gigabit Ethernet backplane. This link is used for interconnection between other interface cards or network modules attached to the router Gigabit Ethernet backplane bypassing the router host CPU; thus, increasing CPU performance by decreasing CPU processing.
If I do a sh ip int brief on the switch, I have 26 interface but only 24 are physicaly present on the front.The type of the 0/25 and 0/26 are the same : media type is 1000BaseXThe interface gi 0/26 is up up but the 0/25 is down down.
How many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View Relatedi have 68 sites with Routers. On each site I have one equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
I have 15 off this sites that the access via telnet to the equipment’s connected after the routers are not working. These sites are using Router Cisco 3925. The other sites that are working are using Routers Cisco MWR 2921.
Both router models are running the same configuration with no filter on it.
The equipment’s after the routers are all accessed directly via telnet without the router. If the router is directly plugged to the equipment the 15 sites with Router Cisco 3925 are not accessed via telnet.
There is any bug related with the IOS version that Router Cisco 3925 is using?:
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T2, RELEASE SOFTWARE (fc1).ROM: System Bootstrap, Version 15.0(1r)M8, RELEASE SOFTWARE (fc1).System image file is "flash0:c3900-universalk9-mz.SPA.151-2.T2.bin"
We are in the process of determining and going to subscribe the speed/bandwidth required from Telco for our DMVPN HUB Headend.
Apparently we are going to have max of 30 remote sites(spokes)
Our design is basically just 1 single headend(hub) and spokes.
1x ISR 3925 (HUB)
30x ISR 2911 (SPOKES)
Spokes subscribed speed is either 512kbps or 1Mbps depending on sites.
How we can determine the optimal speed/bandwidth to subscribe on our HUB.
We currently installed a 100Mbps fiber line with Ethernet hand-off. I purchased a Cisco 3925 ISR to be the gateway for this connection. I am not going to use it for any security purposes. I have an ASA5520 that will do that work. Right now I am currently just trying to get the router online.
I know the following
Laptop <--->GB 0/1((()))GB0/0<---->Ethern
et handoff from ISP.
I can ping and SSH to the outside interface of the router from outside the network. I can also ping and SSH to the router from the laptop that is directly attached to the routers GB0/1 port. From the Router's CLI I can ping IP addresses on the internet. From the laptop I can not. I can not access the internet through the router though. Here is my config.Building configuration...
Current configuration : 3724 bytes!! Last configuration change at 02:17:03 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsisversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname XXXNAMEXXX!boot-start-markerboot-end-marker!!logging buffered 51200 warningsenable secret 4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX!no aaa new-modelmemory-size iomem 20!no ipv6 cefip source-routeip cef!!!!!no ip domain lookupip domain name XXXXXXXXXXXXXXDomainXXXXXXXXXXXmultilink bundle-name authenticated!!crypto pki token default removal timeout 0!crypto pki trustpoint TP-self-signed-XXXXXXXXXXXXXXXXenrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-XXXXXXXXXXXXXrevocation-check nonersakeypair TP-self-signed-XXXXXXXXXXXXXX!!crypto pki certificate chain TP-self-signed-XXXXXXXXXXXXXXcertificate self-signed
[code]...
I just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
terms of Performance for 3925, 3925E and 3945.
didn't see much different between 3925 and 3925E except an additional port.