I need to install an ATM module in a 3925 router. I would like to know if this card is that I have to buy with the transceiver(SFP)?
Will use a fiber cable LC LC singlemode fiber optic.
Module: NM-1A-OC3-POM
Transceiver :SFP-OC3-IR1
I am using a Cisco 3925 router and attempting to install an EHWIC card with no luck. The card I am trying to install is EHWIC-D-8ESG.
I have powered down the router, inserted the card into the proper slot and my router doesn't seem to recognize the new card. Is there a command I need to enter to enable the card?
I have a 3925 Router with a 48 port switch module (part number SM-D-ES3G-48-P). I have no problem accessing the 3925 Router, but when I go into the 48 port, I get an error that reads
Error Hardware not supported by firmware. Try loading a newer software instead. System Resetting...
I know that the wrong IOS is installed on the switch, but the problem is that this is an endless loop. The switch resets then comes back to the same error. How to get the switch out of this loop so that I can load the correct IOS.
confirm the C3KX-NM-10G module is hot-swappable.i have checked the cisco's website and it says " Although network modules are hot-swappable, we recommend installing a network module before powering the switch"
What steps i need to follow to install the module?
I have Inspiron 1545 with windows 7 home basic. When I try to install bluetooth module it asks me to activate Bluetooth using wireless switch. How do I do it..
View 4 Replies View RelatedAny doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.
View 5 Replies View RelatedI am going to install new Nexus 7K. Installed SUP and one 32-Port 10Gb module. When I open the box to install this 10Gb module, I saw that there is a carbon paper is tighted with ***** on the top of the module. confirm either it will insert in Switch with carbon paper or have to remove this carbon paper?
View 1 Replies View RelatedI've been researching the 3750-x Netflow support but I'm not 100% sure of how much support it has. From what I've read the only way to get NetFlow support is to install a specific module that provides NetFlow. I also heard about how it might support s-flow but I haven't found out for sure.
View 8 Replies View RelatedI have spend half day to look up this question in cisco official web site, but get nothing . Any infomation about vpn performance of 3925 router？Produce : cisco 3925 ( Cisco 3925 Security Bundle w/SEC license PAK )Question is , how much ipsec vpn tunnels can be carried as a vpn server of this bundle ? if more licenses may be bought, how much most tunnels can be held？
View 5 Replies View Relatedhow to setup natting on a 3925 router.
View 1 Replies View Relatedi said in the title i have forgot my password for my cisco3925 rourtor and how to reset my password
View 3 Replies View RelatedTo have GRE tunnel support in a Cisco3925 do I need any specific license (DATA, SEC, etc) or it is include in the UNIVERSAL IOS?
View 1 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View Relatedi have 68 sites with Routers. On each site I have one equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
I have 15 off this sites that the access via telnet to the equipment’s connected after the routers are not working. These sites are using Router Cisco 3925. The other sites that are working are using Routers Cisco MWR 2921.
Both router models are running the same configuration with no filter on it.
The equipment’s after the routers are all accessed directly via telnet without the router. If the router is directly plugged to the equipment the 15 sites with Router Cisco 3925 are not accessed via telnet.
There is any bug related with the IOS version that Router Cisco 3925 is using?:
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T2, RELEASE SOFTWARE (fc1).ROM: System Bootstrap, Version 15.0(1r)M8, RELEASE SOFTWARE (fc1).System image file is "flash0:c3900-universalk9-mz.SPA.151-2.T2.bin"
We currently installed a 100Mbps fiber line with Ethernet hand-off. I purchased a Cisco 3925 ISR to be the gateway for this connection. I am not going to use it for any security purposes. I have an ASA5520 that will do that work. Right now I am currently just trying to get the router online.
I know the following
Laptop <--->GB 0/1((()))GB0/0<---->Ethern
et handoff from ISP.
I can ping and SSH to the outside interface of the router from outside the network. I can also ping and SSH to the router from the laptop that is directly attached to the routers GB0/1 port. From the Router's CLI I can ping IP addresses on the internet. From the laptop I can not. I can not access the internet through the router though. Here is my config.Building configuration...
Current configuration : 3724 bytes!! Last configuration change at 02:17:03 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsisversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname XXXNAMEXXX!boot-start-markerboot-end-marker!!logging buffered 51200 warningsenable secret 4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX!no aaa new-modelmemory-size iomem 20!no ipv6 cefip source-routeip cef!!!!!no ip domain lookupip domain name XXXXXXXXXXXXXXDomainXXXXXXXXXXXmultilink bundle-name authenticated!!crypto pki token default removal timeout 0!crypto pki trustpoint TP-self-signed-XXXXXXXXXXXXXXXXenrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-XXXXXXXXXXXXXrevocation-check nonersakeypair TP-self-signed-XXXXXXXXXXXXXX!!crypto pki certificate chain TP-self-signed-XXXXXXXXXXXXXXcertificate self-signed
[code]...
I was trying to give the following host name to my 3925 router.Iht comes up with the following error. DRT0(config)#hostname DRT#0 % Hostname contains one or more illegal characters.% Hostname "DRT#0" is not a legal LAT node name, Using "CISCO_000000" DRT#0(config)#
View 2 Replies View RelatedIm going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
Model:Cisco EPC3925Vendor:CiscoHardware Revision:1.0 MAC Address:18:59:33:ad:b0:a0Bootloader Revision:2.3.0_R1Current Software Revision:EPC3925-ESIP-16-v302r125532-110504cFirmware Name:epc3925-ESIP-16-v302r125532-110504c.binFirmware Build Time:May 4 17:40:26 2011Cable Modem Status:OperationalWireless Network:Enable
I was trying to enable AutoQoS on my router 3925 GE interfaces, but failed to do so !! But I was able to do so on FE interfaces !! I have Security/K9 and Data/K9 license on this router. Or do I still miss out anything ?? I am on IOS 150-1(M4).
I was able to enable AutoQoS on all my Cisco 2811 and 1841 routers !
how to configure a site to site tunnel using IKEv2 between our offices using an ASA 5515-X and a Cisco 3925 router running IOS 15.2 Connecting ASA to ASA and ASA to Router via IKEv1 works fine. Want to take advantage of the improvements in IKEv2 but I'm having difficulty with the ikev2 setup on the router. Here is the pertinent ASA side config--
ASA IP: 5.5.5.5
Router IP: 10.10.10.10
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1
[Code].....
I need 3925 router that support BGP as well as IPSEC VPN. is this correct part number i ordered? CISCO3925-SEC/K9. Its always hard to understand Cisco licensing, specially new one. will above package will have router wth ipbasek9+seck9?
View 4 Replies View RelatedI have a new 3925 ISR G2 router with the universal IOS, 256kb flash in CF0, 1gb flash in CF1. When the router boots it prompts to enter initial config. Whether I say yes or no, enter the appropriate info, "write memory", and reload it comes up with a blank config. I've checked the config-register (2142), copied the start up-config to nvram:, flash0:, and flash1: but nothing works.
View 2 Replies View RelatedI have one router 3925 equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
Please find the attached config details.
I have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
View 5 Replies View RelatedI have a question regarding the 3925 router. In the past on my old 3660's, in order to add a new line to an ACL, I would have to remove the entire ACL and readd it when adding new ACL lines to the list. Is this required on the 3925's, or is it like the ASA 5520's where you can just add an ACL any 'ol time without having to remove/add the entire ACL list?
View 2 Replies View Relatedwe are configuring a ras on 3925 router with e1 controller. when we connect the e1 controller to pbx we got on pbx a no frame alarm (detailed error is that we have nfas but we do not have cas). what could be the error? do the router need dsp to have a framed e1?
View 1 Replies View Relatedchecked all the recovery doc, however, there is no one specific for 3900 series router
View 2 Replies View RelatedI have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View RelatedI am trying to set up a redundant OSPF setup and I am seeing behavior I don't quite understand. At the main office I have two routers, a 3825 connected via full DS3 to the MPLS cloud, and a 3925 connected to the Internet for VPN backup.There are nine branches, but I am only going to talk about three. The three branches all connect together as well as having their own MPLS connections to the cloud. They are all 2821 routers with a 4.5 Mbps multilink interface into the cloud (three T1's). One of the branches has a backup IPSec/GRE Internet connection that I want any of them to be able to use in case of an MPLS problem (which there have been many lately, sometimes involving all of them going down at the same time). The connection into MPLS uses Inter-area OSPF with the provider. The Tunnel connection is also using IA OSPF (the main office is area 0 and this cluster of branches are all on area 100).
OSPF seems to be behaving oddly. At the main office, on the 3825 with the "backup" shut off, if I do "show ip route 10.51.0.0" it shows this output: [code]If the metric before was 24, why would it put in a route with a metric of 53 now? What's worse is that the branches all think they should connect over the MPLS and the main office sends everything over the VPN. It works, but I don't really want asymetric routing! I have included some configs as well... those which I consider relevant. I am including a diagram that has more on it than is relevant, but what I referenced is here (and yes, spanning-tree has been properly configured on the red fiber connections with the connection between FEC2960 and Hl2960 blocking, but try to ignore the LAN stuff because this is in a transitional phase right now anyway).
I want to connect my clients from the Windows WS to a VPN Tunnel using 3925 router w/o Cisco VPN client. Is there the way to use native IPSec client on Windows XP or Windows 7?
View 1 Replies View RelatedMonitoring H.323? I've got a 3925 running15.1(3)T with 9 PRI's. Because of our volume, syslogging is not the desired solution. We want something that we can potentially graph over an 8 hour period, so while the RTMT is accurate, either it won't store the data for 8 hours, or we aren't using it correctly (plus, mgmt may want access to the stats/graphs, and we're not keen on granting them access). So far, we've used: [code] None of these seem to accurately portray utilization. cdsp Active Channels seems to get the closest, so perhaps I have to tweak it a little bit, but so far, nothing accurate.
View 3 Replies View RelatedI have a network architecture like the one HERE but with alot more spokes (32). Would my cisco 3925 be able to support so many crypto maps?
View 2 Replies View RelatedRecently fitted 2 3925 routers on a WAN Mulitlink (2 * 2Mb) which has been working reasonably well but have noticed CRC's and intremitteny up/downs on E1 links. This could be due to issues with Microwave links but on checking nothing stands out on these - no errors or traps form radios.
Anyway taing a closer look at E1 lines and had some questions:-
Microwave radios E1 circuits are set to UNFRAMED, router interfaces set to NO-CRC4, didnt think this was the same?
E1 card are VWIC3-2MFT-T1/E1 and also noticed the following:-
no network-clock-participate wic 0(same for 1 and 2), my card are in slot 0 and 1.
I see no slips etc on E1 controllers .
