Cisco Switching/Routing :: Enable AutoQoS On Giga Interface On 3925 Router?
Apr 3, 2012
I was trying to enable AutoQoS on my router 3925 GE interfaces, but failed to do so !! But I was able to do so on FE interfaces !! I have Security/K9 and Data/K9 license on this router. Or do I still miss out anything ?? I am on IOS 150-1(M4).
I was able to enable AutoQoS on all my Cisco 2811 and 1841 routers !
View 3 Replies
ADVERTISEMENT
Jun 27, 2010
I just receive a new Cisco 3925 with a etherswitch module 24 port :
SM-ES3G-24-P,I successfully boot the switch module and gain access to it.
I found some documentation on CCO but I don't sorted out this small information :,
Switch#sh cdp neig Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone, D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port IDRouter Gig 0/26 143 R S I CISCO3925 Gig 2/0Switch#
The Router is connected to the switch module via a HIMI :
The Cisco enhanced EtherSwitch service modules also provide a physical Gigabit Ethernet serializer/deserializer integrated circuit transceiver (HIMI) interface. In the Cisco 2900 series and Cisco 3900 series routers, the HIMI link on the Cisco enhanced EtherSwitch service modules is connected to the router internal Gigabit Ethernet backplane. This link is used for interconnection between other interface cards or network modules attached to the router Gigabit Ethernet backplane bypassing the router host CPU; thus, increasing CPU performance by decreasing CPU processing.
If I do a sh ip int brief on the switch, I have 26 interface but only 24 are physicaly present on the front.The type of the 0/25 and 0/26 are the same : media type is 1000BaseXThe interface gi 0/26 is up up but the 0/25 is down down.
View 3 Replies
View Related
Jan 9, 2013
I just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
View 4 Replies
View Related
Oct 15, 2012
Cisco C2960S IOS:12.2(55)SE5
Cisco C3560X IOS: 12.2(55)SE3
The 3560 switch is serving as an access and distribution layer switch. End devices are connected to it and it also implements IP routing via SVI and L3 ports.Auto qos voice cisco-phone has been implemented on applicable access layer ports. SRND4 is being used.
2960:
mls qos map policed-dscp 0 10 18 24 46 to 8
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue output cos-map queue 1 threshold 3 4 5
mls qos srr-queue output cos-map queue 2 threshold 1 2
mls qos srr-queue output cos-map queue 2 threshold 2 3
mls qos srr-queue output cos-map queue 2 threshold 3 6 7
[code].....
Question 1:Why is the auto qos generated policed-dscp map different on these two switches?The Cisco Smart Business Architecture LAN configuration files guide [URL] does not specifically use the 3560 in their examples, they use the 3750 but it's my assumption that the same techniques, configs apply with regard to my specific feature questions. When using a 3750 in the Access layer, the guide shows (page 15) the same auto qos generated policed-dscp map configuration that is on my 2960. The SBA LAN config guide shows that when using a 3750 as a Distribution layer switch (page 26), the policed-dscp map configuration is the same that I see on my 3560.In the configuration guide for the 3750 distro switch, there is no auto qos applied as there are no access ports, so the mls qos commands are manually input. Since my 3560 does have access ports, auto qos generated the mls qos commands, and the results are the same be it following the guide and manually entering (per distro switch guidelines) or using auto qos. This leads to question 2...
Question 2:Why is the mls qos map policed-dscp configuration different depending on use as an access vs. distribution switch?
Question 3: On the 3560, access ports that have "auto qos voice cisco-phone" applied are put into queue-set 2 (output). Queue-set 2 (output) uses default values (not configured). Is this correct and desirable? If so, why? The 2960 has all ports in queue-set 1, regardless of being an access device port or a trunk port connected to the 3560 (as per the SBA LAN config guide EgressQOS macro commands). The 3560 trunk ports are all also configured to use queue-set 1 (output), again as per the SBA LAN config guide EgressQOS marco commands.
View 1 Replies
View Related
Oct 27, 2011
I can´t configure speed in a giga port on WS-C3560-24PS-S switch(config-if)#speed ? no negotiate Do not negotiate speed
do you know if the port support speed 100??
because I need to connect with 2955C-12 switch in one port: 100BASE-FX (Multimode Fiber) uplinks, this port its only 100mbps?
and the switch C3750G-12S-E can I configure the ports on 100mbps?
View 4 Replies
View Related
Nov 8, 2011
I was trying to give the following host name to my 3925 router.Iht comes up with the following error. DRT0(config)#hostname DRT#0 % Hostname contains one or more illegal characters.% Hostname "DRT#0" is not a legal LAT node name, Using "CISCO_000000" DRT#0(config)#
View 2 Replies
View Related
Nov 13, 2011
I have a question regarding the 3925 router. In the past on my old 3660's, in order to add a new line to an ACL, I would have to remove the entire ACL and readd it when adding new ACL lines to the list. Is this required on the 3925's, or is it like the ASA 5520's where you can just add an ACL any 'ol time without having to remove/add the entire ACL list?
View 2 Replies
View Related
Jan 30, 2013
terms of Performance for 3925, 3925E and 3945.
didn't see much different between 3925 and 3925E except an additional port.
View 5 Replies
View Related
Apr 11, 2012
Is it possible to create a vlan on a standard 3925? We have no addon cards installed.
View 3 Replies
View Related
Jul 9, 2012
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies
View Related
Jan 19, 2012
I have a 3925 Router with a 48 port switch module (part number SM-D-ES3G-48-P). I have no problem accessing the 3925 Router, but when I go into the 48 port, I get an error that reads
Error Hardware not supported by firmware. Try loading a newer software instead. System Resetting...
I know that the wrong IOS is installed on the switch, but the problem is that this is an endless loop. The switch resets then comes back to the same error. How to get the switch out of this loop so that I can load the correct IOS.
View 1 Replies
View Related
Jan 14, 2012
On my 2650 Router it just has only Telnet password.It has no enable mode password set.After reboot it is goes to prompt mode BB.I am unable to go to enable mode .how can i go back to enable mode on this router?
View 13 Replies
View Related
Oct 31, 2012
My engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
View 3 Replies
View Related
Feb 12, 2013
We have CISCO ASR 1002 router on our DC, I want to enable TACACS on this router.what is the usage of key, we need a separate key for every device? or. [code]
View 9 Replies
View Related
Jan 14, 2013
We currently installed a 100Mbps fiber line with Ethernet hand-off. I purchased a Cisco 3925 ISR to be the gateway for this connection. I am not going to use it for any security purposes. I have an ASA5520 that will do that work. Right now I am currently just trying to get the router online.
I know the following
Laptop <--->GB 0/1((()))GB0/0<---->Ethern
et handoff from ISP.
I can ping and SSH to the outside interface of the router from outside the network. I can also ping and SSH to the router from the laptop that is directly attached to the routers GB0/1 port. From the Router's CLI I can ping IP addresses on the internet. From the laptop I can not. I can not access the internet through the router though. Here is my config.Building configuration...
Current configuration : 3724 bytes!! Last configuration change at 02:17:03 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsisversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname XXXNAMEXXX!boot-start-markerboot-end-marker!!logging buffered 51200 warningsenable secret 4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX!no aaa new-modelmemory-size iomem 20!no ipv6 cefip source-routeip cef!!!!!no ip domain lookupip domain name XXXXXXXXXXXXXXDomainXXXXXXXXXXXmultilink bundle-name authenticated!!crypto pki token default removal timeout 0!crypto pki trustpoint TP-self-signed-XXXXXXXXXXXXXXXXenrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-XXXXXXXXXXXXXrevocation-check nonersakeypair TP-self-signed-XXXXXXXXXXXXXX!!crypto pki certificate chain TP-self-signed-XXXXXXXXXXXXXXcertificate self-signed
[code]...
View 10 Replies
View Related
Sep 22, 2011
I have a problem with the command mls qos trust dscp, I used the ios c2800nm-ipvoice_ivs-mz.124-25f.bin but i can not enable dont show me the complete command in the interface Ethernet o Giga. I want to configuring mls qos trust dscp.
View 1 Replies
View Related
Sep 21, 2011
how to enable protection path in GSR 12404 router Gigi interface connected to mux port. Like we configure APS group for POS interfaces.
View 1 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Mar 27, 2012
I have purchased these two switches from ebay as a test lab, I plan to connect them up via a gigastack modulecable and enable ip routing on the c3550 and vlans to talk to each other.
I'm very much a procurve person and really need to get into the cisco switching.I will want to trunklacp between the switches - whats the process is setting that up on cisco switches?
View 1 Replies
View Related
May 16, 2012
Router 1941 is installed with additional 4 Gig-interfaces card; we have 4 ADSL Router with 4 MB connections. I need to connect all the ADSL connection to the router 4 port and combine them into 16 MB, is there any way to combine 4 Gig interfaces?
View 4 Replies
View Related
Oct 25, 2012
I have a pair of router Cisco 2800 running in HSRP, now I want to configure one sub interface with another sub net, Will my current IP on physical interface work or do I need to create two Sub interfaces for each network. Do i must need encapsulation on sub interface
Current Config:-
Router 1:-
interface FastEthernet0/1description Connect to LAN_SW1 Gi1/0/1ip address 192.168.1.13 255.255.255.0no ip redirectsduplex autospeed autostandby 1 ip 192.168.1.1standby 1 priority 90standby 1 preempt
Router 2:-
interface FastEthernet0/1description Connect to LAN_SW2 Gi1/0/1ip address 192.168.1.3 255.255.255.0no ip redirectsduplex autospeed autostandby 1 ip 192.168.1.1standby 1 priority 110standby 1 preempt
For second network I do not require HSRP
Router 1:-
interface FastEthernet0/0description Connect to LAN_SW1 Gi1/0/1no ip addressduplex fullspeed 100
[ code]...
Router 2:-
interface FastEthernet0/0description Connect to LAN_SW2 Gi1/0/1no ip addressduplex fullspeed 100
[Code]...
View 3 Replies
View Related
Mar 23, 2013
I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
From which release this command is available?
View 1 Replies
View Related
Apr 3, 2013
Have a 3750X running at the moment and has about 30 vlans all connected and just use the ip route global config command to enable routing. Plan is to switch out to the 4503E, with IPBase license. When ever I issue the same command, and do a show run its not there. I get no error when I issue the command either. And yes I have rebooted. Do I need to use RIP or OSPF routing? When I do a show ip route the screen looks the same with all the codes, though gateway of last resort isn't set even though I do have ip route 0.0.0.0 0.0.0.0 a.b.c.d in the config. Or is ip routing just enabled by default?
View 6 Replies
View Related
Oct 12, 2012
In my preparation for my coming CCNA certification I am experimenting with different network configurations. In my test network I am currently working with a "Router on a stick" setup. A Cisco 2611 router connecting a Cisco 2950 switch. VLANs configured on the switch and subinterfaces + dot1q encapsulation configured on the router. Switch only supports dot1q.Router's Eth0/1 is connected to the Switch Fa0/24 port which is also set to trunk mode. I am using a normal Cat5e twisted pair cable to connect the 2 devices.
VLANs are working since I can connect a workstation to an access port for example fa0/2 (vlan2) and get Internet access.I can also ping any of the subinterfaces of the router from the workstation.With the current setup I am not able to ping the switch from the router, or the other way around, so in other words I can't remote manage the switch from a telnet or SSH session with this setup. What I am missing?Just to be clear I am pinging the switch directly from the router (Router2611#ping 172.16.100.2), so please ignore all static routes and OSPF. [code]
View 3 Replies
View Related
Dec 19, 2012
I have two Catalyst 2960 Series (48 port) switches with the newest Cisco IOS installed. There is also a Cisco 2600 Series Router which I can't manage because it's ISP managed.
Now the problem is as follows. I'd like to create two VLANs, one in the IP range 192.168.0.xxx and the other in the 192.168.1.xxx. Now the router has a gateway IP address 192.168.1.1 .
Would it be possible to somehow connect these two VLANs with the router so that these 2 VLANs can't see each other but they can ofcourse both contact the router and exit on the internet?
View 3 Replies
View Related
Aug 6, 2012
I was able to setup my router c819 with Verizon 3G but there is one minor thing that on the console it keeps saying:
Aug 7 21:04:30.067: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
Aug 7 21:04:35.111: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
Aug 7 21:06:18.423: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
The interface Cellluar0 is connected to Verizon 3G network and I'm able to ping and get to the internet just fine. I did few research and some people said it was access list. My ACL is below but I can't find anything wrong with it.
!
!
interface Cellular0
ip address negotiated
[Code].....
View 4 Replies
View Related
Nov 14, 2011
We have a 1841 Cisco router for one of our remote sites and we have the GRE over IPSec tunnel on it (with our datacenter router) for the connectivity. The LAN facing interface becomes UP/Down (status 'UP', Protocol 'Down'). When I login the router and 'shut' and then 'no shut' the interface, the interface becomes UP and everything starts to work. Traffic starts to flow across it. But after some time, some hours or sometimes some days, the interface is again back to up/down status. The router is connected to a non-Cisco switch. I do see some CRC's increasing very slowly, but apart from that there seems nothing wrong with the interface in sho int fas0/0 command:
!
RTR01#sho int fas0/0
FastEthernet0/0 is up, line protocol is down
Hardware is Gt96k FE, address is 0026.cb91.ee48 (bia 0026.cb91.ee48)
[Code]....
View 1 Replies
View Related
Apr 19, 2013
I have been trying to enable L3 intervlan routing on C2960S Switch with ip routing command and that was the output from the Switch: [code]
View 6 Replies
View Related
May 21, 2013
I have router Cisco 2691 and Cisco 7604 and want to play with AutoQoS Cisco feature. But on both there is no such command But why?
View 1 Replies
View Related
Nov 1, 2011
I just finished setting up a bundle of (2) T1's in a multilink bundle and I'm having issues with one of the T1's not wanting to join the bundle.
The router I'm using on the remote office location is a 3620 router running code c3620-i-mz.121-1c.bin
The campus router which is a 7206 is setup the same exact way with multilink 240 and like I've said, serial 0/0 is joined to the bundle just fine, so we are running off one T1 connection.
The serial interface that is not working is: serial 0/1
Here is a show-run:
interface Multilink240
ip address 172.18.xxx.xxx 255.255.255.252
ip route-cache flow
ip ospf network point-to-point
service-policy output PhonesFirst
ppp multilink
[code].....
View 3 Replies
View Related
Mar 14, 2013
I have already exploited Metro Ethernet, but I don't understand why auto-negotiation does not support for Ten Giga ports?
View 8 Replies
View Related
Sep 9, 2011
My friend recently let me have his Seimens Gigaset SE567 modem which i needed cause it has a router but as soon as i switched it with my old router which is a Westell 6100f,the internet light wont show up ..so i contacted verizon and they said that there service is plug and play type of service so i am lost on what to do ..i looked around the forums and i got close by going to the browser and typing the IP but from there i am stuck ..i don't know how to set up any thing in the configurations.
View 2 Replies
View Related
Feb 14, 2012
How do I enable SSH on 4507. I do not see "ip ssh ..." commands config#ip ssh (I do not see "ip ssh " commnd)
Do i need to enable something else?
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
View 1 Replies
View Related