Cisco Switching/Routing :: Create Vlan On Standard 3925?
Apr 11, 2012Is it possible to create a vlan on a standard 3925? We have no addon cards installed.
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3560 Possible To Create Vlan Inside Transport Vlan?
Jan 10, 2012Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedCisco Switching/Routing :: Cannot Create Vlan On 2811
Dec 13, 2012This is a 2811 rotuer running Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2) Not sure why this isn't working. Can see it expects to parse the command. Can see this device is vtp server. Can see other vlans were defined here.
Router(config)#vlan ?
accounting VLAN accounting configuration
ifdescr VLAN subinterface ifDescr
Router(config)#vlan 35
^
% Invalid input detected at '^' marker.
[code]....
Cisco Switching/Routing :: Create New VLAN On 4500?
Jan 24, 2012I have an in production x2 4500's which I would like to add a new vlan and IP address to.
Sample config...
interface Vlan65
ip address 10.100.6.2 255.255.255.248
no ip redirects
no ip unreachables
no ip proxy-arp
standby 65 ip 10.100.6.1
standby 65 timers 1 3
standby 65 preempt delay minimum 120
Cisco Switching/Routing :: Nexus 5010 - Unable To Create More Than 256 VLAN In N5k
Jun 23, 2012I am not able to create more than 256 VLAN in Cisco Nexus 5010 switch. While creating I am getting "No VLAN resources available for VLAN creation" Details below -
Switch model - 5010
Software : NX OS 4.0 (1a)
Error Message:
Nexus_5010(config)# vlan 417
ERROR: No VLAN resource available for VLAN creation.
Cisco Switching/Routing :: 3750 - Make Switchport 10.1.1.13 And Then Create IP VLan?
Feb 7, 2013Currently have two routers inside our network.
One is the default GW 10.1.1.13
One is Jump Router for ATT 10.1.1.12
Both connected to HP Procurve L2 switch
The ATT Router is 10.1.1.2Want to replace GW and Jump with one 3750 L3 switch.icomplish this with only one port g0/1 connected to HP Procurve?Can I make the switchport 10.1.1.13 and then create a ip vlan999 10.1.1.12?route all to 10.1.1.2Or do I just connect two ports, and hardcode them with an ip?
Cisco Switching/Routing :: Create Two Trunk Links Between 4506 And 4948 And Allow Vlan 540?
Sep 24, 2012Current Situation:We are able to reach server IP -10.203.206.40 from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.
Requirements
==========
1) Now we would like to add one more L3 interface between 4506 & 4948 for redundancy purpose.
2) Make available Vlan 540 in 4948 from 4506... need to create two trunk links between 4506 & 4948 and allow vlan 540.
Cisco Switching/Routing :: Create New Vlan On 3750 Switch With Trunk Mode
Jan 16, 2013This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies View RelatedCisco Switching/Routing :: 2560 Create Dynamic VLAN For Specific Group Of Users
Feb 6, 2012We have Cisco Cat4503 series L3 Switch and Cisco L2 2560 Series Switches, some of the users want to have a dynamic VLAN membership, and connecting with the network as mobile users,
can it possible and create dynamic VLAN for specific group of users.
Cisco Switching/Routing :: 3925 - How To Add New ACL
Nov 13, 2011I have a question regarding the 3925 router. In the past on my old 3660's, in order to add a new line to an ACL, I would have to remove the entire ACL and readd it when adding new ACL lines to the list. Is this required on the 3925's, or is it like the ASA 5520's where you can just add an ACL any 'ol time without having to remove/add the entire ACL list?
View 2 Replies View RelatedCisco Switching/Routing :: 10.2.2.2 / Can Use Standard ACL In Route-map For BGP Fall-over
Jan 22, 2012I haven't got time to test different configurations yet. Just want to quickly ask here about the fall-over route-map configuration. I saw lots of example using pip prefix-list to specify the next-hop for tracking. Is that the only way you can do it? Can you just use a standard ACL to specify that host like permit host 10.2.2.2? ip prefix-list will do like ip prefix-list seq 5 permit 10.2.2.2/32. And you apply the prefix-list to route-map then. ACL will work?
View 2 Replies View RelatedCisco Switching/Routing :: 3750 / MST Pre-standard And Links Down
Sep 3, 2012Checking the logs we have seen the following messages:
%SPANTREE-3-PRESTD_NEIGH: pre-standard MST interaction not configured (Port-channel3). Please, configure: 'spanning-tree mst pre-standard' on ports connected to MST pre-standard switches.
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel3, changed state to down
%LINK-3-UPDOWN: Interface Port-channel3, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet2/0/1, changed state to down
When this happened, the interface that was actually blocked by STP didn't come to forwarding state, and as a result this switch became isolated.This switch is connected to a switch that runs standard MST, and to some switches that run PVST but have bpdufilter enabled as we don't want them to participate on the STP. It is a 3750 switch with software version 12.2(55)SE5.
As far as I knew, when a MST pre-standard BPDU was received, the interface was able to receive more pre-standard BPDUs, but I didn't know it would turn the link down. Why the links went down, and if there is any way we can configure those links to accept only MST standard BPDUs.
I would also like to know if there is any chance a switch running PVST can send a MST pre-standard BPDU if it has a software version 12.2(25)SEE3.
Cisco Switching/Routing :: To Get CbQos On Asr 1002s With Standard OIDs
Jul 3, 2012I would like to get CbQos on a Cisco ASR 1002S (IOS-XE Software (PPC_LINUX_IOSD-IPBASEK9-M), Version 15.1(1)S1). With the standard OIDs (cbQosIfIndex - 1.3.6.1.4.1.9.9.166.1.1.1.1.4).
View 3 Replies View RelatedCisco Switching/Routing :: Catalyst 2960 POE With Pre Standard IP Phones
Mar 21, 2013I have a Catalyst 2960-S switch and a pre-standard IP Phone (Cisco 7960). When I connect the phone to the switch the switch recognizes the phone and supplies power. I would like to prevent this behaviour. ie. I would like to disable detection of pre-standard equipment. Is there a command I can issue on the 2960-S to do this? For example, on a switch from a different vendor I can issue the command: no power pre-std-detect to prevent it from detecting the 7960 phone, is there an equivalent command on the Catalyst 2960-S ?
View 3 Replies View RelatedCisco Switching/Routing :: 4500 Can Connect 10Gb SFP+ To Standard 1Gb SFP
Nov 15, 2011I'm looking at provisioning a Catalyst 4500 with a WS-X4712-SFP+E module to allow for future 10Gb connectivity via 10Gb SFP+ interfaces. These cards are backwards compatible with standard 1Gb SFP interfaces but I'm wondering about the other way around; ie. can you populate these blades with 10Gb SFP+ interfaces when they connect to Catalysts with only 1Gb SFP interfaces at the other end?
The data sheets don't really explain this. It seems pointless getting 10Gb SFP+ interfaces for the 4500 when it's only 1Gb at the access layer end, but these access switches will be replaced in the near future (~12 months) and if the 10Gb SFP+ interfaces support connections at 1Gb speeds upfront, it would mean I could retain these interfaces when the access switches upgrade to 10Gb connectivity capabilities down the track. Does the 10Gb SFP+ interfaces are compatible with 1Gb SFP's or only other 10Gb SFP+ interfaces?
Cisco Switching/Routing :: Interface Gi On SMES3G-24P 3925
Jun 27, 2010I just receive a new Cisco 3925 with a etherswitch module 24 port :
SM-ES3G-24-P,I successfully boot the switch module and gain access to it.
I found some documentation on CCO but I don't sorted out this small information :,
Switch#sh cdp neig Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone, D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port IDRouter Gig 0/26 143 R S I CISCO3925 Gig 2/0Switch#
The Router is connected to the switch module via a HIMI :
The Cisco enhanced EtherSwitch service modules also provide a physical Gigabit Ethernet serializer/deserializer integrated circuit transceiver (HIMI) interface. In the Cisco 2900 series and Cisco 3900 series routers, the HIMI link on the Cisco enhanced EtherSwitch service modules is connected to the router internal Gigabit Ethernet backplane. This link is used for interconnection between other interface cards or network modules attached to the router Gigabit Ethernet backplane bypassing the router host CPU; thus, increasing CPU performance by decreasing CPU processing.
If I do a sh ip int brief on the switch, I have 26 interface but only 24 are physicaly present on the front.The type of the 0/25 and 0/26 are the same : media type is 1000BaseXThe interface gi 0/26 is up up but the 0/25 is down down.
Cisco Switching/Routing :: Do The Catalyst 2960-S Switches Support Pre-standard PoE?
Jun 14, 2012I have a customer with Cisco 7940 and 7960 IP phones that they do not plan to replace. They do want a new LAN and are looking at the Catalyst WS-C2960S-48FPD-L and WS-C2960S-24PD-L as access layer devices.
these switches support the Cisco pre-standard PoE required by the 7940 and 7960 IP phones.
Cisco Switching/Routing :: Unable To Ping / SSH To Interface On 3925?
Jan 9, 2013I just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
Cisco Switching/Routing :: Difference Between 3925 / 3925E And 3945
Jan 30, 2013terms of Performance for 3925, 3925E and 3945.
didn't see much different between 3925 and 3925E except an additional port.
Cisco Switching/Routing :: Hostname Error On 3925 Router
Nov 8, 2011I was trying to give the following host name to my 3925 router.Iht comes up with the following error. DRT0(config)#hostname DRT#0 % Hostname contains one or more illegal characters.% Hostname "DRT#0" is not a legal LAT node name, Using "CISCO_000000" DRT#0(config)#
View 2 Replies View RelatedCisco Switching/Routing :: 3925 ISR - Possible To Copy Files Between Flash
Jul 9, 2012I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies View RelatedCisco Switches :: Used Two SF-300 Switch And Create 4 VLans And Inter-VLan Routing
Apr 8, 2013 I used two sf-300 switch and create 4 vlans and intervlan routing is working fine.
Port 1 - 10 -------------> Vlan 1
Port 2 -20----------------> Vlan 2
Port 3 - 30------------------> Vlan 3
Port 4 - 40--------------------> Vlan 4
giga1 -----------------> connected to router (This router used for intervlan routing).
SF-300 Port 1 is connected to Internet Modem. This modem worked as dhcp server also for vlan 1, my problem is that when vlan 1 is not communicate to vlan2,3,4 and 2,3,4 are not communicating.
How i can communicate vlan 1 to 2,3,4 vlan.
how i can connect the modem in switch? Access port or Trunk port ( Presently available in vlan 1 Access port)Any route i need to make? sf-300 or modem or router?
Cisco Switching/Routing :: Enable AutoQoS On Giga Interface On 3925 Router?
Apr 3, 2012I was trying to enable AutoQoS on my router 3925 GE interfaces, but failed to do so !! But I was able to do so on FE interfaces !! I have Security/K9 and Data/K9 license on this router. Or do I still miss out anything ?? I am on IOS 150-1(M4).
I was able to enable AutoQoS on all my Cisco 2811 and 1841 routers !
Cisco Switching/Routing :: 3925 With 48 Port Switch Module Infinite Loop
Jan 19, 2012I have a 3925 Router with a 48 port switch module (part number SM-D-ES3G-48-P). I have no problem accessing the 3925 Router, but when I go into the 48 port, I get an error that reads
Error Hardware not supported by firmware. Try loading a newer software instead. System Resetting...
I know that the wrong IOS is installed on the switch, but the problem is that this is an endless loop. The switch resets then comes back to the same error. How to get the switch out of this loop so that I can load the correct IOS.
Cisco Switching/Routing :: 3750 - Extending VLAN To Remote Switch That Already Has VLAN ID In Use
Jan 10, 2013I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
Cisco Switching/Routing :: Route Data From Vlan 10 To Vlan 20 On 2960s?
Mar 31, 2013i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
Cisco Switching/Routing :: 3750G / VLAN 1 Is The Only VLAN And Its Disabled
Sep 16, 2012I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies View RelatedCisco Switching/Routing :: L2tpv3 Vlan-to-vlan Tunnel On 890
Jun 13, 2011I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
Cisco Switching/Routing :: Low Bandwidth On 3750 From Vlan To Vlan?
Nov 20, 2012We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
Way To Create VLAN
Mar 26, 2012I wanted to have 3 vlan for my switch just for security reasons.(We do not want different Vlan members interact with each other)
I created 3 untagged Vlans on 48 port switch.
So ports 1-16 in Vlan 192.168.1.1/25
So ports 17-32 in Vlan 192.168.2.1/25
So ports 33-48 in Vlan 192.168.3.1/25
Cisco Switching/Routing :: Can Create Svi On ASR 1002
Apr 22, 2013I need to know, can i create svi on the ASR 1002 ?
View 2 Replies View RelatedCisco Switching/Routing :: 3750X Cannot Create A Vrf
Mar 4, 2013I want to confirm this is a licensing issue. On a 3750X with ipbase, I cannot create a vrf. So I would need the universal image, and that is a seperate license, correct?Is there a link that describes the difference bewteen ipbase and univeral images?
View 6 Replies View RelatedCisco Switching/Routing :: Cant Create VRFs On A 3750X?
Mar 1, 2013I am having an odd issue on a couple of new 3750X switches.I am trying to configure VRF-lite and it is not recoginizing the command.Does that make any sense? I have goggled the syntax ans it should be right.
View 12 Replies View Related