I wanted to have 3 vlan for my switch just for security reasons.(We do not want different Vlan members interact with each other)
I created 3 untagged Vlans on 48 port switch.
So ports 1-16 in Vlan 192.168.1.1/25
So ports 17-32 in Vlan 192.168.2.1/25
So ports 33-48 in Vlan 192.168.3.1/25
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedOn our HP switches we have an 'Outside' VLAN where any device connected to these VLAN ports can use the ISP's 'outside' IP addressing for direct Internet access to bypass our firewall. We use this for videoconferencing devices.What is the correct way to do this on a Cisco SF-300-48P??Presently I have ports 1-4 in vlan 50 Outside as 'untagged,' and the same ports as 'forbidden' in vlan 1 Default. Is this the correct configuration?? In HP switches these ports in vlan 1 Default would be configured 'No' and 'untagged' in vlan 50 Outside.Tried talking to Cisco but their phone support is not working.
View 6 Replies View RelatedUser want to create on 5 network , 100.x , 200.x , 210.x , 250.x , 220.x .at the ASA5510, no enough port for 5 network.So I want to create 4 vlans on eth 0/3. I can create vlan but i cannot run this command " switchport mode trunk" " "switchport trunk allowed vlan list" how can be done for that?
Actually i want to use like thisASA5510-----4 vlans on eth 0/3------switch----vlan200,vlan210,vlan250,vlan220.
May I know the reason why we cannot create interface vlan on Cisco ASA 5510?
View 2 Replies View RelatedThis is a 2811 rotuer running Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2) Not sure why this isn't working. Can see it expects to parse the command. Can see this device is vtp server. Can see other vlans were defined here.
Router(config)#vlan ?
accounting VLAN accounting configuration
ifdescr VLAN subinterface ifDescr
Router(config)#vlan 35
^
% Invalid input detected at '^' marker.
[code]....
I have an in production x2 4500's which I would like to add a new vlan and IP address to.
Sample config...
interface Vlan65
ip address 10.100.6.2 255.255.255.248
no ip redirects
no ip unreachables
no ip proxy-arp
standby 65 ip 10.100.6.1
standby 65 timers 1 3
standby 65 preempt delay minimum 120
Is it possible to create a vlan on a standard 3925? We have no addon cards installed.
View 3 Replies View RelatedI have got a wireless project with WLC main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .
ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0
and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.
I need to create a DMZ Vlan. Core switch is a 6509. FW is an ASA5520. Need to create a VLAN for DMZ purposes for outside facing servers. NAT is used on ASA.
View 7 Replies View RelatedUnable to create VLAN interfaces in ASA 5510
View 1 Replies View RelatedI am not able to create more than 256 VLAN in Cisco Nexus 5010 switch. While creating I am getting "No VLAN resources available for VLAN creation" Details below -
Switch model - 5010
Software : NX OS 4.0 (1a)
Error Message:
Nexus_5010(config)# vlan 417
ERROR: No VLAN resource available for VLAN creation.
Currently have two routers inside our network.
One is the default GW 10.1.1.13
One is Jump Router for ATT 10.1.1.12
Both connected to HP Procurve L2 switch
The ATT Router is 10.1.1.2Want to replace GW and Jump with one 3750 L3 switch.icomplish this with only one port g0/1 connected to HP Procurve?Can I make the switchport 10.1.1.13 and then create a ip vlan999 10.1.1.12?route all to 10.1.1.2Or do I just connect two ports, and hardcode them with an ip?
I used two sf-300 switch and create 4 vlans and intervlan routing is working fine.
Port 1 - 10 -------------> Vlan 1
Port 2 -20----------------> Vlan 2
Port 3 - 30------------------> Vlan 3
Port 4 - 40--------------------> Vlan 4
giga1 -----------------> connected to router (This router used for intervlan routing).
SF-300 Port 1 is connected to Internet Modem. This modem worked as dhcp server also for vlan 1, my problem is that when vlan 1 is not communicate to vlan2,3,4 and 2,3,4 are not communicating.
How i can communicate vlan 1 to 2,3,4 vlan.
how i can connect the modem in switch? Access port or Trunk port ( Presently available in vlan 1 Access port)Any route i need to make? sf-300 or modem or router?
Current Situation:We are able to reach server IP -10.203.206.40 from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.
Requirements
==========
1) Now we would like to add one more L3 interface between 4506 & 4948 for redundancy purpose.
2) Make available Vlan 540 in 4948 from 4506... need to create two trunk links between 4506 & 4948 and allow vlan 540.
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies View RelatedWe have Cisco Cat4503 series L3 Switch and Cisco L2 2560 Series Switches, some of the users want to have a dynamic VLAN membership, and connecting with the network as mobile users,
can it possible and create dynamic VLAN for specific group of users.
Is it possible to use 1 or 2 of the 4 gigabit ethernet ports from one ACE straight into the other ACE for redundancy? So ACE_01 gig0/4 to ACE_02 gig0/4.If so, is it a case of just having the layer 3 config instead of trunking etc..Also - is it possible to create a context within the same vlan as the Admin context?
View 4 Replies View RelatedWe are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies View RelatedHow do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies View RelatedI have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies View Relatedi need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies View RelatedI'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
EZVPN_Remote(config-if)#int fa1
EZVPN_Remote(config-if)#dot
EZVPN_Remote(config-if)#dot1?
dot1q
EZVPN_Remote(config-if)#dot1
[code]....
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this
View 10 Replies View RelatedI am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
View 1 Replies View RelatedI've been given the task to clean-up our network config, and have walked into a disaster zone.We have a 4510R on site with everyone using the default VLAN, VLAN 1.I have created 4 new VLANS, VLAN100, VLAN150, VLAN200, VLAN250 I have assigned interface addresses to each VLAN and configured Inter VLAN routing.I can route to and from each new vlan with no problem, i.e VLAN250>VLAN100 VlAN100>VLAN200 etc but I can't route to VLAN 1(Default VLAN) from any of them, I can ping the interface on VLAN 1 from any VLAN , but any hosts are unreachable. On the flip side , from VLAN 1 I can route to all of the VLANS.
View 3 Replies View RelatedI have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
[URL]...