This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 RepliesCurrent Situation:We are able to reach server IP -10.203.206.40 from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.
Requirements
==========
1) Now we would like to add one more L3 interface between 4506 & 4948 for redundancy purpose.
2) Make available Vlan 540 in 4948 from 4506... need to create two trunk links between 4506 & 4948 and allow vlan 540.
Currently we have a 6513 core (running IOS and doing limited routing) with VLAN Trunking to about a dozen 3560 edge switches, with various VLANs going to each of the edge switches. All works well. We are downsizing and replacing the 6513 core with a 3750G stack. We have the stack up and running in the lab, and want to slowly (as we move floors) migrate all of the edge switching to the 3750 stack.
The plan is to connect the 3750 stack to the 6513, then slowly migrate the edge switches to the stack (from the 6513). I would like to put in place 4 x 1GB trunk links between the 6513 and the 3750 stack before I start moving edge switches to ensure adequate bandwidth. Once all of the edge switches are on the new 3750 stack, I will start to decommission the 6513.
What is the best way to configure the links between the cores (old 6513 and new 3750 stack)? I can easily get the edge switches configured to the 3750, but am worried about the core links. I really want to avoid having to perform an all-at-once cutover of the cores. Another question is when do I try and migrate the VTP server role from the 6513 to the 3750 stack? I could simply make everything transparent, and ditch server-based VTP, as we rarely change or creat VLANs.
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedI have a 3750 as a core and have a series of HP Procurve switches that are daisy chained using one port. I have two vlans on the port now (6 &9) and everything works fine, all switches communicate and end devices on the switches are also talking. There is a requirement to add a device towards the end of the chain which requires it to connect using Vlan1. Once I add Vlan1 to the port onthe 3750 I lose connectivity to all the HP switches.
View 4 Replies View RelatedCurrently have two routers inside our network.
One is the default GW 10.1.1.13
One is Jump Router for ATT 10.1.1.12
Both connected to HP Procurve L2 switch
The ATT Router is 10.1.1.2Want to replace GW and Jump with one 3750 L3 switch.icomplish this with only one port g0/1 connected to HP Procurve?Can I make the switchport 10.1.1.13 and then create a ip vlan999 10.1.1.12?route all to 10.1.1.2Or do I just connect two ports, and hardcode them with an ip?
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I'm having some trouble getting my head round the following but I think it's routing related?
I have a Cisco 3750 switch with the following configured:
interface Vlan1
ip address 192.168.0.223 255.255.254.0
no ip route-cache
[Code].....
The 3750 is connected to a firewall which handles the routing. From the 3750 I can only ping remote networks from the vlan1 interface not from vlan6,8 or 10 i.e ping 10.34.37.101 (remote network) source 192.168.0.223 (vlan1) works but ping 10.34.37.101 source 10.74.10.1 (vlan10) does not? I can ping 10.34.37.101 from computers on the various vlans but not from the 3750 it self.
I looked at setting a default gateway for the various vlan interfaces
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies View RelatedWhat the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies View Relatedwe are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
i want to create a trunk between 4507 & 3945E router & route two vlans from router 3945E
4507# vlan 99 & 51
# int vlan 99
# ip add 10.22.100.1/24
#int vlan 51
# ip add 10.22.103.1/24
[code].....
4507 version : IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
3945E: 15.1(2)T4 what I am missing?
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedI've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies View Related I used two sf-300 switch and create 4 vlans and intervlan routing is working fine.
Port 1 - 10 -------------> Vlan 1
Port 2 -20----------------> Vlan 2
Port 3 - 30------------------> Vlan 3
Port 4 - 40--------------------> Vlan 4
giga1 -----------------> connected to router (This router used for intervlan routing).
SF-300 Port 1 is connected to Internet Modem. This modem worked as dhcp server also for vlan 1, my problem is that when vlan 1 is not communicate to vlan2,3,4 and 2,3,4 are not communicating.
How i can communicate vlan 1 to 2,3,4 vlan.
how i can connect the modem in switch? Access port or Trunk port ( Presently available in vlan 1 Access port)Any route i need to make? sf-300 or modem or router?
Cisco 4506-E port configuration
WESTERN-4506-01#show int g4/47
GigabitEthernet4/47 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 0022.554c.01fe (
fe)
Description: Trunk to 425
[code]....
Cisco 3750 Configuration
interface FastEthernet1/0/1description 425Linkswitchport trunk encapsulation dot1qswitchport trunk native vlan 30switchport trunk allowed vlan 30,35switchport mode trunkswitchport nonegotiateswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitystorm-control broadcast level pps 300storm-control multicast level pps 300storm-control action trapmacro description cisco-desktopmac access-group AuthorizedHosts in
I have mac address' populated. I can see the device in layout on CNA with the proper name however cannot ping it.
4506 is 10.30.30.1
3750 is 10.30.30.2
I have a couple 3750 switches that I am trying to run VTP Version 3 on.one as primary and the other as "server" which implies secondary from my research. [code]Additionally, running a show VTP devices yields a "No VTP3 devices found" on both devices. Despite ensuring that the domainname and password match.I have a patch cable from Gi1/0/1 on switch one runnning to Gi1/0/1 which from what I read is acceptable on GigE.
View 2 Replies View RelatedI have client who has two distant offices with 3750 L3 as core (do all vlan routing for local office) and multiple L2 access switches with multiple VLAN’s connected to it. First 3750 is hub also connected to internet, second 3750 is spoke and acting as a router on stick. We have eigrp configured on both side ISP provided client 100Mbps link as a trunk with two vlan; vlan10 for voice and vlan20 for data. We assigned two small subnets to these vlans 10.15.17.0/29 and 10.15.17.9/29. Hub addresses are 10.15.17.1 and 10.15.17.9 respectively. How to force voice over VLAN10 and data via vlan20, but still do some load balancing? How to setup default route on second (router on stick) switch?
View 1 Replies View RelatedI have 2 hosts, 1 plugged in fa 0/21 in VLAN 101 and another in fa 0/22 in VLAN 101 on our L2 Cisco 2960. If I try and transfer files from either host the gig 0/1 trunk port on the 2960 leading tot he 3750 fa 0/1 port hits 100mb (using a real time bandwidth monitor tool), but why? This VLAN is on the same switch, why does it go one way up the trunk to the L3 3750 switch? The L3 3750 is the VTP server and the 2960 is a client. I would of thought the traffic stays local. The 2 hosts don't even have a gateway set.To sum up the typology the 2960 and 3750 are trunked using a single cable. The 3750 hangs of a ASA firewall using SVIs.Here is whatthe traffic looks like when copying a file between hosts (2gb file).
3750 L3 Switch (VTP Server)
interface FastEthernet1/0/4
description Trunk to Cisco 2960 Gig 0/1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
[code]....
I need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies View RelatedWe bough an Cisco 2911 router, and as i see the "ip sla monitor" command is not supported. Which license/IOS upgrade should i buy the fullfill this. And i cant add a trunkport to the iunterface even cant add a vlan to interface. How do i a trunkport on the cisco 2911 router. ANd how can i do a vlan on a interface on the router.
View 2 Replies View Relatedwe have a scenario that consists of a Cisco 4507 series core switch with more than 20 vlans which is connected to a C2960G switch( in a nearby building) using a trunk by a fiber connection. Up to this point everyhting is fine . VTP domain is configured on the core switch and we have all of the 20 vlans present correctly on the edge 2960G wich is part of course of this same VTP domain.the fiber connection goes from core switch to a "in the middle location" where we have a fiber patch panel that is connected in a jumper style to another fiber patch panel going to the destination building where the C2960G sits.
Now imagine that Fiber connection from this middle location to the destination C2960 edge switch is down for any possible reason meanwhile the fiber connection from Core switch 4507 to the middle location is still intact.In the same time, in this middle location , we do have a wireless connection which links 1 Cisco 3750G switche ( a different infrastructure and different VTP domain) to another C3560G switch which sits on the same Room in the nearby destination building where we have the edge C2960G, An idea came to me is to connect one of the fiber port (core) in the intact fiber patch panel coming from Core switch 4507 TO an access vlan configured switchport in the 3750G switch ( this switchport will belong to a vlan designed only to trasmit the vlans on the trunk coming from 4507 core switch say VLAN 10) then connect one VLAN 10 access switchport to the destination C2960 edge switch ( the switchport on the c2960G is still a trunk)Will this solution work and all of the 20- 4507 core switch vlans arrive to the destination C2960G ? Or we do need something that tags the 2 VLAN 10 switchports like switchport dot1q tunnel like QinQ
I faced with a strange behavior of ME3600.For testing purposes I linked Cat3550 and ME3600 switches via trunk mode. All interfaces are in Up state. But I couldn't ping SVI200 of Cat switch from ME3600 and vice versa. [cde]
This scheme perfectly works with another L3 swithes. For example Catalist3750. I know that ME doesn't support VTP, DTP and so on. Also, I've tried latest software.
Is it possible to rate limit on a L2 trunk port on a 3750?
current port config and ios are as follows;
interface GigabitEthernet1/0/50
description *** Connection to Fiber Link ***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,172
switchport mode trunk
end
flash:c3750-advipservicesk9-mz.122-46.SE.bin
i was wondering if the "srr-queue bandwidth limit 10" command would work to limit the output from this interface to be 10 % of the port bandwidth and then the same command could be done on the other side.
I am taking only undersize errors on catalyst 3750 trunk interface (attached some outputs)...the other end is a 4500 switch and the interface is clean..can this be related to any bug ? this is my root port and often leading to trouble sometimes STP BPDUs transportation are affected..
View 4 Replies View Relatedcan i have 4 links from an ESX server to 6500 , each link represents a trunk link carries each the same 2 VLAN , 100 and 101 , keep port-channel out of the picture , does it work well?
View 12 Replies View RelatedI have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihomed (Broadcom) on the other side an it is supposed to be on this vlan with one of it's network interfaces. We had a pwer outage and now it cannot communicate on this vlan. However, everything else on the vlan can reach all the other nodes accept this server in the front of my building. All the devices in the same room are linked to the same switch which has one port (fa0/17) on vlan0010 and can ping eachother just fine. The server is hooked to port 24 on my server room switch and Gigabit port one goes to a fiber converter all the way to the back. It then gets converted from fiber to cat5e again and links into the switch (2960) in the backroom.
View 5 Replies View RelatedNeed to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
View 1 Replies View Relateda number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies View RelatedWe had a core switch (Cisco 4503), distribution switches(Cisco 3750) and access switches in our network and consists of many vlans. Almost all vlans uses DHCP Pools. But for few vlans DHCP is not yet configured due to initial design poblems. Recently one of the rogue user in vlan 1 connected to one of the access switch send rogue arp packets to the network (suspecting arp packet with interface vlan 1 ip of core switch with wrong mac-address (gateway ip of vlan 1)) and resulted in a prolonged network outage for the vlan 1. Any way we are going to seggregate vlan 1 into different vlans, but before that we need a temporary plan to block such kinds of attack like enabling DAI in the switch. I have checked the DAI implemenation feasibility with my knowledge and found that it is not possible to configure to the access switches(Cisco 2960) in which the user directly connected. But found that Distribution switch connected to that particular access switch seems to be able to configure since DAI commands are available to configure in switch.
Is it possible to block ARP packets with the interface vlan 1 IP Address with rogue mac-address by configuring DAI in the above mentioned Distribution switch and the port connected to the mentioned access switch?
I have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
I need adding a vlan to the trunks bundled in port channel. I know how to add v lans to a port channel with Cisco IOS but with CAT OS.
I have 2 ports bundled to form ether channel in switch which is running CAT OS. There are already few v lans allowed in the trunk of each interface. now I need to add one more v lan.
For Example:-
v lan 135 needs to be added in addition to the existing v lans.
clear trunk1/2 1-112,115,117-134,136-4094
set trunk 1/2 on dot1q 113-114,116,135
and similarly on the 2nd interface
so if I add vlan135 to the trunk one after another will it cause any service disruption?