Cisco Switching/Routing :: Ping From Vlan Interfaces On 3750 Switch
May 27, 2013
I'm having some trouble getting my head round the following but I think it's routing related?
I have a Cisco 3750 switch with the following configured:
interface Vlan1
ip address 192.168.0.223 255.255.254.0
no ip route-cache
[Code].....
The 3750 is connected to a firewall which handles the routing. From the 3750 I can only ping remote networks from the vlan1 interface not from vlan6,8 or 10 i.e ping 10.34.37.101 (remote network) source 192.168.0.223 (vlan1) works but ping 10.34.37.101 source 10.74.10.1 (vlan10) does not? I can ping 10.34.37.101 from computers on the various vlans but not from the 3750 it self.
I looked at setting a default gateway for the various vlan interfaces
View 3 Replies
ADVERTISEMENT
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Nov 9, 2012
I have a Cisco 2921 and a 3750 stack. I want to use both interfaces on the 2921 to connect to the 3750 stack switch 1 and 2. Is this possible using same ip subnet?
View 2 Replies
View Related
Sep 27, 2012
how my switches are configured, a cisco 3750 and a cisco 4506.[code] i can ping the gateway from the 3750 however cannot get anything past that or enything to it.
View 12 Replies
View Related
Sep 17, 2012
I have 2 switches. 2960 and 3750. I have trunk on both ports of the switch. there are couple of vlans and ports are assigned to those vlans. examples are management, voice and data. int vlan 1 has ip there is default gateway the hosts are able to connect to the internet when connected to the switch.
View 5 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Apr 3, 2012
I have one 12-port 3750 switch having one gig connectivity with ASR-9010 router having IOS-XR. I am not able to ping this link with 9000 mtu size. I have enable system mtu jumbo on switch to 9000 and on ASR router interface mtu is set to 9114. At switch side switch interface is configured as a trunk port and one vlan has been passed on that interface. I am not able to ping the ip 172.16.10.2 with 9000 mtu size.
View 6 Replies
View Related
Nov 12, 2011
Why I cannot ping vlan when no port connect to switch.
View 3 Replies
View Related
Mar 6, 2013
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
Nov 14, 2012
What the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies
View Related
Nov 4, 2012
we are using 3750 and 2950 switches both of them do not support vlan up to 4000 .we need vlan about 3000 .Whic cisco series switch do support vlan up to 4000.
2950
S-SW1.3(config-vlan)#exi
Proposed configuration has too many VLANs for this platform. Reduce the number of VLANs proposed.
S-SW1.3(config)#end
3750
SW1(config-vlan)#exi
proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
View 1 Replies
View Related
Jan 9, 2013
I am using an Old 3500XL and I simply created a
interface VLAN 100
Description ***********
ip address 10.0.1.100 255.255.255.248
no ip directed-broadcast
no ip route-cache
shutdown
no matter what I do i cannot get it to come up, the rest of the switch is default config, I know I am just forgetting something, But I don't know what?
View 8 Replies
View Related
Nov 20, 2012
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
View 2 Replies
View Related
Apr 17, 2012
I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
View 1 Replies
View Related
Sep 26, 2012
I would like to do the following architecture with the same C3750 : network X,Y,Z connected to 3750 in VRF D the 3750 uses a routed interface on subnet E for the default route in VRF D on this routed interface a BYPASS EQUIPMENT the other BYPASS EQUIPMENT interface is connected also to another routed interface on subnet E "also" this routed interface is in another VRF C with other network A and B.do you know if it will work because of 2 routed interfaces on the same IP subnet or is there a way to do that ? the only goal for me is to catch traffic from network X,Y,Z on SYN and ACK.
View 5 Replies
View Related
Apr 23, 2013
I have a client with a 3750x stack. We've upgraded it to IP Services. We have a simple PBR setup. One access-list to forward traffic from a specific LAN ip to another gateway on the network.
I go to vlan1 (default vlan) to apply the PBR and the command takes with no errors, but do a "show run" and it doesn't show up under the interface.
I go to vlan1 and apply a PBR that doesn't exist and the command takes with no errors, and is listed under the interface in the config
I can apply the PBR globally and appears to work, but we can't have it there based on other issues it creates.
config: (all tracks are up)
C3750_stack#show sdm prefer
The current template is "desktop routing" template.
[Code]....
View 8 Replies
View Related
Jul 14, 2012
I`m looking to automate some functions in a web application.Functions like enable/disable interfaces on a Cisco 3550 switch.
View 5 Replies
View Related
Mar 5, 2012
I am trying to test the MTU between two 3750 switches I have in the lab. I've set the MTU with the command "system mtu 9000" on both switches and rebooted.
The only connections on the switches are the gig ports connecting the two switches. Each interface is a member of vlan 1.
I am doing an extended ping. I set the datagram size to 2000. When the df bit is set the ping doesn't go through. If the DF bit is not set the ping goes through.
The debug ip icmp shows, 4d00h: ICMP: dst (1.1.1.1): frag. needed and DF set.
Why is fragmentation needed when the MTU is set to 9000?
GigabitEthernet1/0/1 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0015.2b7d.0d01 (bia 0015.2b7d.0d01)
MTU 9000 bytes, BW 1000000 Kbit, DLY 10 usec,
[Code].....
View 4 Replies
View Related
May 2, 2013
I am trying to config the following setup in the Cisco 1841. Able to ping the IPs of Vlan1(FE0/0/1), Vlan2 (FE0/0/1) and FE0/1 IPs from corresponding networks. But packets are not flowing to other side.
View 3 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Sep 28, 2008
On a 3750 switch, is it possible to configure jumbo frames only on certain interfaces and leave the other ones as they are?
View 9 Replies
View Related
Nov 18, 2012
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies
View Related
May 3, 2012
This would probably sound like a stupid question but it took at least 2 hours of my time so far. I have a 3750 switch where a router and a server is connected. From the switch I can ping the router and server with no issue (directely connected). But from the server I am not able to ping the router. The router and the server are in the same subnet. The router is configured as the default router for the server. I am not able to ping the server from the router either. Here's the output of the ip route from the router. The server IP address is 10.1.200.21 and the router IP address is 10.10.200.1
10.0.0.0/8 is variably subnetted, 8 subnets, 3 masks
C 10.1.30.0/24 is directly connected, FastEthernet0/0.30
C 10.1.20.0/24 is directly connected, FastEthernet0/0.20
[Code].....
View 14 Replies
View Related
Oct 24, 2012
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies
View Related
Oct 28, 2012
I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
Feb 4, 2012
i am stuck in a issue! unable to ping the SVI
i am design a small network for a office.
1 router 2811
1 switch 3750-e
Router is connected to the mpls cloud with ospf.
here re the config.
Router#
int fa0/0
ip 10.10.10.1 255.255.255.252
[Code]....
i connect my laptop and give ip 22.0.68.1 255.255.255.0 and default gateway 22.0.68.251but can not ping SVI VLAN 201 (22.0.68.251) ?
and from the SWITCH i can not ping the 20.20.20.2?
View 38 Replies
View Related
Jan 1, 2012
I have a Cisco 3750 with private VLANS configured.. VLAN 2 is the "primary", VLAN 3 is "isolated" and VLAN 4 is "community". This is all working correctly, however I now have the need to another VLAN called "production". I need the production VLAN to be able to reach all the private VLAN hosts (community and Isolated), and vice versa
View 2 Replies
View Related
Dec 8, 2011
I have a quick query which i need ratified before proceeding. I have the following scenario -
Two Cisco 3750v2 switches with stackwiseISP allocated block of /26 (64 addresses)8 customers each with a VLAN and SVIInternet facing VLAN and SVIDefault route to ISP router Lets say the ISP has given me the network range 10.10.10.0/26 (we'll assume this is routable on the internet for the purposes of this example) and a default gateway to the internet of 10.10.10.1 within this range. I have configured a public facing VLAN as follows -
VLAN 300
name PUBLIC
int VLAN 300
IP Address 10.10.10.2 255.255.255.252
I have then created a default route as follows -
ip route 0.0.0.0 0.0.0.0 10.10.10.1
With this configured, the switch can successfully route upstream to the internet with no problems. I have then moved onto the customers and depending on what service they have purchased, I have subnetted the 10.10.10.0/26 range into smaller subnets. See as follows -
Customer A - 10.10.10.4/30
Gateway IP - 10.10.10.5
Useable IPs - 10.10.10.6
Customer B - 10.10.10.8/29
Gateway IP - 10.10.10.9
Useable IPs - 10.10.10.10 - 10.10.10.14
This continues for each customer depending on how many IP's the have purchased. I have then assigned these IP ranges to a customer VLAN and SVI as follows -
Customer A
VLAN 10
name CUST-A-VLAN
int VLAN 10
ip address 10.10.10.5 255.255.255.252
[code].....
It is then up to the customer as to what equipment they use and how they NAT or firewall their internal networks.
View 5 Replies
View Related
Feb 19, 2013
We have a couple of Cisco switches and connected a (Windows 7) laptop to one of them and it gets its IP address from a DHCP server.I can now ping the IP from all of the switches, no problem, also not when I log on to the core switch in the same VLAN as both notebooks. But from my (Windows 7) laptop, which is in the same VLAN as the target laptop, I cannot ping it.
I checked, default gateway is good on both sides, as are DNS servers.
Target notebook ---- Catalyst 3560 V2 switch === Core Catalyst 3750 switch (stack) === Catalyst 3560G switch --- My notebook
View 4 Replies
View Related
May 30, 2012
I have an ASA that houses 11 VLANs, and I am trying to add a 12th.One of the VLANs is for PCs that have internet only access.The new VLAN will be similar, but for multifunction printers only.VLAN 99 is for internet only and works fine, I can ping the gateway of 10.99.3.33 from any PC in that VLAN.I am creating VLAN 98, modeling it after VLAN 99, and I cannot get a PC in the vlan to ping the gateway of10.98.3.17.Both switch and ASA show the new VLAN 98 as UP, switchport is UP/UP.I have deleted and recreated VLAN 98 a few times, but I cannot get a PC VLAN 98 connectivity.Once it is working on the core switch, I will add it to the trunk to the IDS switches. VTP is not in use, everything is manual. [code]
View 4 Replies
View Related
Oct 15, 2012
I have created two vlans, vlan 1 data and vlan 200 voice. the issue is that when an on one vlan i cannot ping the default gateway of the othe vlan from my PC. An using sge 2010p switches.
below is my configuration
p route 0.0.0.0 0.0.0.0 192.168.0.1
ip dhcp relay address 192.168.0.100
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable(code )
View 3 Replies
View Related
