Cisco Switching/Routing :: 2811 - Unable To Ping SVI VLAN
Feb 4, 2012
i am stuck in a issue! unable to ping the SVI
i am design a small network for a office.
1 router 2811
1 switch 3750-e
Router is connected to the mpls cloud with ospf.
here re the config.
Router#
int fa0/0
ip 10.10.10.1 255.255.255.252
[Code]....
i connect my laptop and give ip 22.0.68.1 255.255.255.0 and default gateway 22.0.68.251but can not ping SVI VLAN 201 (22.0.68.251) ?
and from the SWITCH i can not ping the 20.20.20.2?
View 38 Replies
ADVERTISEMENT
Aug 23, 2009
Aug 24 11:32:16.275 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to down
Aug 24 11:32:36.827 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to up
Aug 24 11:35:23.854 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/2, changed state to down
Aug 24 11:35:24.854 AEST: %LINK-3-UPDOWN: Interface FastEthernet0/1/2, changed state to downesw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)(code)
When the above problem happens, as work-around, we delete VLAN.DAT file on the Compact Flash of this 2811 router and recopy the VLAN>DAT file back to teh Compact Flash.
Then it runs for a few weeks and the same problem happened.
Then we put a new Compact Flash and recopied VLAN.DAT to new CF and it ran for 3 weeks and same problem started again.
Could be 2811 router motherboard? This customer has thousands of these 2811 routers in identical setups and this is the only router that is having this problem.
View 6 Replies
View Related
Jul 10, 2012
Yesterday I configured the 7010 Nexus switch. I created a VDC and allocated few ports and configured VLAN for testing. After enabling feature interface-vlan i was allowed to configured L3 interface for the vlan. I assigned ip address and connected few server to check the reachability but it says Destination Host Unreachable.
NX OS Ver : n7000-s1-dk9.5.2.4.bin
Configuration of the VDC below.
feature telnet
feature udld
feature interface-vlan
feature lacp
[Code]....
View 2 Replies
View Related
Dec 13, 2012
This is a 2811 rotuer running Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2) Not sure why this isn't working. Can see it expects to parse the command. Can see this device is vtp server. Can see other vlans were defined here.
Router(config)#vlan ?
accounting VLAN accounting configuration
ifdescr VLAN subinterface ifDescr
Router(config)#vlan 35
^
% Invalid input detected at '^' marker.
[code]....
View 5 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
May 22, 2013
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
View 12 Replies
View Related
May 2, 2013
I am trying to config the following setup in the Cisco 1841. Able to ping the IPs of Vlan1(FE0/0/1), Vlan2 (FE0/0/1) and FE0/1 IPs from corresponding networks. But packets are not flowing to other side.
View 3 Replies
View Related
May 30, 2012
I have an ASA that houses 11 VLANs, and I am trying to add a 12th.One of the VLANs is for PCs that have internet only access.The new VLAN will be similar, but for multifunction printers only.VLAN 99 is for internet only and works fine, I can ping the gateway of 10.99.3.33 from any PC in that VLAN.I am creating VLAN 98, modeling it after VLAN 99, and I cannot get a PC in the vlan to ping the gateway of10.98.3.17.Both switch and ASA show the new VLAN 98 as UP, switchport is UP/UP.I have deleted and recreated VLAN 98 a few times, but I cannot get a PC VLAN 98 connectivity.Once it is working on the core switch, I will add it to the trunk to the IDS switches. VTP is not in use, everything is manual. [code]
View 4 Replies
View Related
Oct 15, 2012
I have created two vlans, vlan 1 data and vlan 200 voice. the issue is that when an on one vlan i cannot ping the default gateway of the othe vlan from my PC. An using sge 2010p switches.
below is my configuration
p route 0.0.0.0 0.0.0.0 192.168.0.1
ip dhcp relay address 192.168.0.100
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable(code )
View 3 Replies
View Related
May 26, 2013
I have a cisco 876 with, c870-adventerprisek9-mz.124-6.T9.bin. I have configured a VLAN with ID 230, an SVI with IP 192.168.230.1/24 and I have assigned switch port fa 2 to it…
interface Vlan230
ip address 192.168.230.1 255.255.255.0
VLAN ISL Id: 230
[Code]......
View 5 Replies
View Related
May 27, 2013
I'm having some trouble getting my head round the following but I think it's routing related?
I have a Cisco 3750 switch with the following configured:
interface Vlan1
ip address 192.168.0.223 255.255.254.0
no ip route-cache
[Code].....
The 3750 is connected to a firewall which handles the routing. From the 3750 I can only ping remote networks from the vlan1 interface not from vlan6,8 or 10 i.e ping 10.34.37.101 (remote network) source 192.168.0.223 (vlan1) works but ping 10.34.37.101 source 10.74.10.1 (vlan10) does not? I can ping 10.34.37.101 from computers on the various vlans but not from the 3750 it self.
I looked at setting a default gateway for the various vlan interfaces
View 3 Replies
View Related
Nov 12, 2011
Why I cannot ping vlan when no port connect to switch.
View 3 Replies
View Related
Nov 12, 2012
I have 2 routers, one is an Apple AirPort Extreme with a static outside IP address, I also have a Cisco 871 with a static outside IP address. The Airport Extreme connects to a switch on the private network and has an IP address ending in .1. The Cisco 871 connects to the same Private network and it ends in .2. The 871 is setup as a VPN Server. now when clients connect to the VPN they can ping the VLan IP Address on the 871, but they can t ping any other hosts on the smae network. The hosts on the private network can ping the vlan on the 871.
View 7 Replies
View Related
Apr 28, 2012
We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies
View Related
Jan 9, 2013
I just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
View 4 Replies
View Related
Nov 17, 2012
I have a vlan defined in FWSM for server farm there is a one server with two IP addresses and teaming has done on it how ever from FWSM i am able to ping both IP addresses but from core 6509 switch i am only able to ping one ip address. from FWSM show ARP command displays the same virtual mac addresses against both IPS of the same server.
View 2 Replies
View Related
Sep 20, 2012
I cannot ping and end node on my system from my Cisco 2911. I've tried to configure my computer to ping the device and I am able to. It seems the difference between using my computer and the 2911 is that with my computer I am able to set the default gateway as the end node's ip.
View 1 Replies
View Related
Mar 11, 2012
We have a 3750 and a 3560 defined as a layer 2 switches. One gig port on each switch is trunked to layer 3 switches, which containall the VLAN definitions etc. The other gig port on the 3650 and 3750 switches are trunked together to provide an alternative path in the event of a failure.
We have added a new device to the 3750 and given it a VLAN 9, and the VLAN added to allowable VLANS on both trunk ports between the layer 3 and layer 2 devices ie:
switch port trunk allowed vlan 9,10,20,30,40,50,60,90,200,202,206,211,212,700.
From either of the 3750 or the 3560 we can ping any device on any VLAN on any switch in this group with exception ofVLAN 9. We can however ping the ip address of VLAN 9 on the layer three switches.
View 2 Replies
View Related
May 1, 2013
i have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
View 14 Replies
View Related
Dec 3, 2011
I've got a 2621 configured as my main gateway to the internet - right now it's obtaining a DHCP ip from a the ISP's proprietary router set to bridged mode.
As of now, I'm unable to ping the internal interface of the router. I can ping external IP's only, even though I have DNS servers listed, i am unable to resolve host names. I'm running a few servers to which people are able to connect to my web server, among other services. I even have a crypto map setup to another 2621 across the country and can ping all internal ips on the other end... I JUST CANNOT PING THE INTERNAL INTERFACE of the router!!
I've noticed that when I ping the router during it's boot process (using linux un-interupted) I get a response in a very short window, then dies again. I'll post my config below:
[code]....
View 9 Replies
View Related
Apr 1, 2013
I am using a Cisco SG-300 28 port switch in layer 3 mode as my default gateway for all my devices. I have two vlans on the switch, vlan 1 and vlan 4. Both are pulling valid IP addresses in their scope from the DHCP server, and both have valid DNS settings. I set a static route to the Internet on the switch to our firewall (192.168.5.254). All devices connected to vlan 1 are able to access the Internet, however all devices connected to vlan 4 cannot get past the switch. A tracert from one of these devices shows it hits the switch as the gateway, but gets no further. [code]
View 4 Replies
View Related
Feb 4, 2013
i configured the VLAN810, with DHCP services, while i try to ping the host which is connected to gi 1/0/2 from my gi 1/0/1 , i can't ping the same vlan host , while i try to debug ip icmp its showing ,
C3750XB11#sh running-config
Building configuration...
Current configuration : 12053 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
[code]....
View 5 Replies
View Related
Apr 6, 2012
I have a Nexus 5548 installed (layer 2 device only) with several 10G ports supporting IBM P770 systems and a TSM (Tivoli Storage Manager) system on a single VLAN. All of the Nexus 5548 ports are configured for jumbo frames. I was ask to install a new server on the same VLAN as the others but as 1G port without jumbo frames to allow communications with the TSM server. I'm assuming that the 1G port for this new server without jumbo frames configured on the Nexus 5548 will not be unable to communicate with the TSM server that is on the same VLAN with it's Nexus 5548 10G port configure using jumbo frames.
View 5 Replies
View Related
Jun 23, 2012
I am not able to create more than 256 VLAN in Cisco Nexus 5010 switch. While creating I am getting "No VLAN resources available for VLAN creation" Details below -
Switch model - 5010
Software : NX OS 4.0 (1a)
Error Message:
Nexus_5010(config)# vlan 417
ERROR: No VLAN resource available for VLAN creation.
View 5 Replies
View Related
Mar 19, 2013
I have one issue on Vlan in Cisco 3750X switches , I have 2 Offices , I am sitting at corp OFfice and i have one 3750 ( 10.10.1.36)Switch at my location , in my remote office i have one more switch 3750 ( 10.10.33.1) and i am able to access the both vlan IPS with out any issue , now i have some network components in Vlan33 ( 10.10.33.1) at my remote office . i am able to ping 10.10.33.1 IP from my corp office , but i am not able to ping any network devices in 10.10.33.5 example : 10.10.33.5 is my Cyberoam IP at remote location and i am not able to ping , i have taken a trace route and not able to find the issue as i am not much femilar , ping 10.10.33.5 at remote location devicec
I am giving the Configuration for both locaitons below :
10.10.1.36 - Corp Office 3750 Switch:
sh run
L3-#sh running-config
Building configuration...
[Code].....
View 1 Replies
View Related
Nov 16, 2011
I have router connected to 2 3550 switches directly. 3550A and B switches are running HSRP. OSPF is running between Router and 2 switches.
From Switch B i can ping the Router Wan interface but not the internet sites. from Switch A i can ping any sites?
Switch B
3550SMIB# sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1
[Code]......
View 7 Replies
View Related
Feb 7, 2012
The network is set up like this.
Host -----> 3750 (classic) running IPSERVICES stack ----> 3550 router -----> VPN 3005 Concentrator.
IP routing is disabled on the 3750 (it's acting solely as a switch) IP routing is enabled with an EIGRP process running on the 3550 router that has the network for the 3005 broadcasting.
I can ping the vpn 3005 concentrator from a telnet session in the 3550 but not from the 3750.I can ping between the 3750 and the 3550 vlan management interfaces. Visually speaking it's like this
3750 ------> 3550 [Success!!!!]
3550 ------> VPN 3005 Concentrator [Success!!!!]
3750 ------> 3550 --xxxx--> VPN 3005 Concentrator [Timeout....]
I know this because I tracerout to the 3005 from the 3750 and it resolved the default gateway configured for the 3550 properly but then started timing out.
The 3750 is trunked to the 3550.
3750 is vtp client mode
3550 is vtp server mode
I'm wondering if there's a layer 2 issue involved here as it is a VTP domain and maybe it's not returning properly.
View 2 Replies
View Related
Apr 6, 2012
Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
View 12 Replies
View Related
May 19, 2013
I am unable to connect a Wifi Modem wiith 2960 Switch having VLAN 1,Attached is the network diagram,what configurations i have to modified it,I need to Connect A Wifi Modem on VLAN 1 ,Connectivity is working fine between VLAN 10 and VLAN 1.What should be the next step to Connect Wifi Modem to VLAN 1 so that Users on VLAN 10 should connect to Internet.
View 14 Replies
View Related
Apr 22, 2012
Here is my configuration below , i have upgraded my C-3750 switch IOS from IPbase to IPservices , after upgrading i have tried to apply PBR on my Vlan 4 and failed , when i am tying to apply route-map to Vlan4 the command was taking but i am unable to see the route-map when sh run , i am giving the command as "ip policy route-map TTSL" in my Vlan4 , below is the configuration.
In Vlan2 i have connected one ISP and Vlan4 I have connected one ISP , my local subnets are 192.168.1.x and 192.168.2.x , now i want to route the 192.168.1.x traffic from Vlan2 and 192.168.2.x Traffic from Vlan4 .
sh boot
coreswitch#sh boot
BOOT path-list : flash:c3750-ipservices-mz.122-35.SE5/c3750-ipservices-mz.122-35.SE5.bin
[Code].....
View 9 Replies
View Related
May 27, 2013
I have a multiple Offices in my location , all my external users are connecting my site using Cisco Client to site VPN and accessing my 2 sites , All users are able to access my 2nd office servers which are in 10.10.0.x pool , I have a different vlan in that same location with 10.10.35.x series and users are not able to access this pool servers , I am not much familiar with Routing . i am using ASA 5520 firewall .
View 11 Replies
View Related
May 30, 2012
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
View 3 Replies
View Related
Jan 11, 2013
I have set up a 2811 with seperate VLANs for phones, and another for computers/printers. Fa0/0 is trunked to a 3560 switch, which has all end devices plugged in. I have enabled the IP Routing commands on both devices, and from advice turned off proxy-arp on the VLANs on the router (unsure if this is causing the issue). The setup is as follows
Computer VLAN = 192.168.20.0
Phone VLAN = 192.168.50.0
Both on the same subnet, along with a router loopback address in the same subnet, at 192.168.10.1.I am having an issue understanding why, but if I try to ping a phone from a PC it times out. Or if I try to type the phone's IP into an internet browser to get the phone's GUI on screen, it fails. This should not be happening as IP routing has been enabled on both, and everything is in the same subnet, correct? PC's can ping other PC's and network printing works fine. Phones register and operate fine, but the two VLAN's will not interoute.Furthermore if I try and ping the router's loopback from the switch, it fails. But the trunk is up and operational because DHCP and devices work within their own VLAN. If I try to ping end devices from the switch, it returns 100%. There seems to be an issue with the router looping the different networks together.
View 35 Replies
View Related
