I cannot ping and end node on my system from my Cisco 2911. I've tried to configure my computer to ping the device and I am able to. It seems the difference between using my computer and the 2911 is that with my computer I am able to set the default gateway as the end node's ip.
View 1 Repliesi have a device connected to 2960 switch. It is an access port and i could ping the device from other switches , also from outside the lan. But i am not able to ping the device from 2960 switch alone. I suspected and checked the arp table and it was showing as incomplete. I created the manual arp entry and tried pinging but no luck.
View 14 Replies View Relatedlast week I installed a new router (2911) in my network.We had to create two different VLANs for the new setup to work as wanted.I have a Windows 2008 R2 which is a Domain Controller for Active Directory on the ip address 192.168.0.195.That server (HP DL180 G6) has two NICs. One has the above IP address and the other one has 192.168.0.199.
On the other VLAN, I have a server, running the same OS, that I want to re-join, as it formerly was, the AD on the first server (192.168.0.195). This server has the new IP address 192.168.10.194.All these are connected to a Cisco switch SG 200-50 Gigabit Smart Switch. That one is connected to a Cisco 2911 router.
The problem is that, once the old 192.168.0.194 got to be 192.168.10.194, the 192.168.0.195 can't ping it anymore... At least not all the time... Sometime it works, sometimes not... Neither can't the 10.194 ping the 0.195 all the time. When one way works the other one doesn't... When one pings the other one successfully, the other one can't...
I have a 2911 router where I was configuring the device to allow remote desktops connections. Everything is working properly, but for some reason my ACL has disappeared.
View 5 Replies View RelatedFrom My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedI have the following setup where the Cisco ME 3400 provided by the ISP.
My Cisco 2911 is configured as below:
CORE_Router#sh run
Building configuration...
Current configuration : 6075 bytes
[Code].....
we have the following setup for our network :
UserNetwork - ASA5550 - WAN Router 2911 - ISP Netowrk - Branch Routers 877s / 1941s
Since last week we started noticing this problem that the branch users started to complain of slow application response.. After verifying it with the ISP and middle network we noticed that if i ping from my machine (ie usernetwork) to the WAN Router interface (facing the ASA) , i get time outs.. which is strange cause this is directly connected to it via ethernet cable.
I have a spare Cisco 857w that I am playing around with to learn.I managed to reset it to default, upgrade the ios to 12.4 However for the llife of me I cannot ping this device.
View 1 Replies View RelatedI have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
I have 2 routers, one is an Apple AirPort Extreme with a static outside IP address, I also have a Cisco 871 with a static outside IP address. The Airport Extreme connects to a switch on the private network and has an IP address ending in .1. The Cisco 871 connects to the same Private network and it ends in .2. The 871 is setup as a VPN Server. now when clients connect to the VPN they can ping the VLan IP Address on the 871, but they can t ping any other hosts on the smae network. The hosts on the private network can ping the vlan on the 871.
View 7 Replies View RelatedI just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
I have a vlan defined in FWSM for server farm there is a one server with two IP addresses and teaming has done on it how ever from FWSM i am able to ping both IP addresses but from core 6509 switch i am only able to ping one ip address. from FWSM show ARP command displays the same virtual mac addresses against both IPS of the same server.
View 2 Replies View Relatedi am stuck in a issue! unable to ping the SVI
i am design a small network for a office.
1 router 2811
1 switch 3750-e
Router is connected to the mpls cloud with ospf.
here re the config.
Router#
int fa0/0
ip 10.10.10.1 255.255.255.252
[Code]....
i connect my laptop and give ip 22.0.68.1 255.255.255.0 and default gateway 22.0.68.251but can not ping SVI VLAN 201 (22.0.68.251) ?
and from the SWITCH i can not ping the 20.20.20.2?
Yesterday I configured the 7010 Nexus switch. I created a VDC and allocated few ports and configured VLAN for testing. After enabling feature interface-vlan i was allowed to configured L3 interface for the vlan. I assigned ip address and connected few server to check the reachability but it says Destination Host Unreachable.
NX OS Ver : n7000-s1-dk9.5.2.4.bin
Configuration of the VDC below.
feature telnet
feature udld
feature interface-vlan
feature lacp
[Code]....
I've got a 2621 configured as my main gateway to the internet - right now it's obtaining a DHCP ip from a the ISP's proprietary router set to bridged mode.
As of now, I'm unable to ping the internal interface of the router. I can ping external IP's only, even though I have DNS servers listed, i am unable to resolve host names. I'm running a few servers to which people are able to connect to my web server, among other services. I even have a crypto map setup to another 2621 across the country and can ping all internal ips on the other end... I JUST CANNOT PING THE INTERNAL INTERFACE of the router!!
I've noticed that when I ping the router during it's boot process (using linux un-interupted) I get a response in a very short window, then dies again. I'll post my config below:
[code]....
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
I have router connected to 2 3550 switches directly. 3550A and B switches are running HSRP. OSPF is running between Router and 2 switches.
From Switch B i can ping the Router Wan interface but not the internet sites. from Switch A i can ping any sites?
Switch B
3550SMIB# sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1
[Code]......
The network is set up like this.
Host -----> 3750 (classic) running IPSERVICES stack ----> 3550 router -----> VPN 3005 Concentrator.
IP routing is disabled on the 3750 (it's acting solely as a switch) IP routing is enabled with an EIGRP process running on the 3550 router that has the network for the 3005 broadcasting.
I can ping the vpn 3005 concentrator from a telnet session in the 3550 but not from the 3750.I can ping between the 3750 and the 3550 vlan management interfaces. Visually speaking it's like this
3750 ------> 3550 [Success!!!!]
3550 ------> VPN 3005 Concentrator [Success!!!!]
3750 ------> 3550 --xxxx--> VPN 3005 Concentrator [Timeout....]
I know this because I tracerout to the 3005 from the 3750 and it resolved the default gateway configured for the 3550 properly but then started timing out.
The 3750 is trunked to the 3550.
3750 is vtp client mode
3550 is vtp server mode
I'm wondering if there's a layer 2 issue involved here as it is a VTP domain and maybe it's not returning properly.
Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedI have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies View RelatedI set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies View RelatedI am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedAfter I changed customer router to CISCO 2911 from H3C firewall, the WAN interface can not ping its gateway after about 10 minites, I do not know why. it works well before I change the device. [code]
View 10 Replies View Relatedi downloaded and transfered the new ios to the 2911, but no install routine started.
View 3 Replies View Relatedafter installation of demo versions of 2900-SEC-TEMP & 2911-2921-SSLVPN-TEMP & rebooting the 2911 router I do not have access SSL commands.Show license indicates that 2900-SEC-TEMP & 2911-2921-SSL-TEMP licenses are active but NOT IN USE.
View 1 Replies View RelatedI am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
I have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
View 21 Replies View RelatedI have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies View RelatedI've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
we are in the planning phase for a network upgrade. We have two C2960 Switches connected via one (L2) Etherchannel (4x1 Gbit/s) which works very well. In the next phase we would like to upgrade our router to an 2911 series which has 3 gb interfaces. and indeed we would like to create an etherchannel as well. our plan is to use 2 of the 2911 to connect to the first 2960 switch and the one left to the other 2960. i think we will achieve some redundancy with this config.
View 6 Replies View Relatedconnected DSL directly to 2900 series router , but as DSL public IP is not static (dynamic) its difficult to access Router when out of home, any other means to access router without static IP
View 2 Replies View Related