I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 RepliesI attached the terminal to the console port to watch the bootup sequense, but nothing appear the same cable used on athor switches and router without any issue.procedure to access the router noting that Giga ports not working also.
View 2 Replies View RelatedI have issue with Cisco Router 2801's Console Port. My student was doing a lab and he said during configuration, Console Port stopped responding. He was in middle of configuration, so now at present, only telnet is able to login on "R2>" user mode, enable password is not set, so getting "R2>en % No password set R2>" I have tried different terminal software but no output from Console Port, changed the Console Cables, replace with working console cables, change speed (baud) settings. Also tried to connect same console with "AUX" port and got same error mentioned above. AUX Port responds but I am not able to change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically damaged.
View 4 Replies View RelatedI have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
I have a brand new 2911 router out of the box. I attached a terminal to the console port and watched the bootup sequence. I get the "press return to get started" at the end but I can't get any response. I just used the same cable and terminal on a 3750 switch and an ASA. What am I missing?
View 3 Replies View RelatedI not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies View RelatedWhen i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies View RelatedWe have purchased a number of 2911 routers.We got Base & security license as we wanted to enable encryption. However we probably wont use the security.We are replacing 2811 routers.Unfortunately the 2811 routers have FXS ports with 2 - 4 POTS handsets - I completely forgot about these ports when I was ordering.Now I have VIC3-FXS cards which are ok in the 2911 but unfortunately I cant get them to work.I am missing PVDMs (well adapters anyway), and even if I got them the router wont take any commands relating to voice due to the license.Is is possible to 'rehost' the security and turn it into a UC ?I am new to these 2911 and Licensing.
View 1 Replies View RelatedI have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies View RelatedI have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
I have a 2911 router with 15.1(4) Ios Version. I need to enable the evaluation sna feature but when I try to enter the command "license feature snasw" but I get an error, the command "License feature" does not exist.
View 3 Replies View RelatedI am planning on having a contractor in to configure some new routers and would like for him to login using the local account on the routers while company personal continues to use radius is this possible.
View 6 Replies View RelatedMy engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
I am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies View Relatedwhether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies View RelatedWe have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
I am having 2911 router running with C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)IOS and i have configured the following commands for eigrp
-router eigrp 100
-network 10.20.0.0
-no auto-summary
It takes all 3 commands but when i check through show run command i am not seeing no auto-summary command.
how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies View Relatedi have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View RelatedI have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies View RelatedI purchased an old cisco 831 for practical studies for a cisco certification. I purchased the console cable (serial/rj45) and a usb->serial converter cable. However when I open my terminal application (tera term) After I select the right com port (3) and make sure the connection settings are right. It will just sit idle and not show any data from the device. Was I sold a faulty device? It lights up and has three lights on.
Everytime I look at a manual or cisco video I am given the impression the terminal application will just automatically connect. But whenever I try I get nothing.
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
I have a 3560-24ps, and I'm having issues with it booting. When I power the device up all the front panel lights come on like normail, and then the system light starts flashing like normal, but after 5 - 6 seconds the system light goes off. I don't get any output from the console, and the fans still run.
View 5 Replies View RelatedI cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies View RelatedI have two 3560s that i would like to upgrade. But first i would like to make -absolutely- sure i dont wind up in a situation where i have to roll back over a console connection.to the day i still cant understand why oh why someone removed (or chose not to implement it everywhere) tftpdnld from rommon ;)
View 8 Replies View RelatedIs there a way to turn off 802.1x authentication messages to the console of a 3750 switch? The issue we have is that we like to monitor the terminal when remotely configuring our switches. However, every time a computer authenticates to the network we get messages and sometimes quite a few depending on the situation.
View 3 Replies View RelatedI have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
I have 2 3750-x members in a stack running 12.2(58)SE2. I am able to console into the stack master, which happens to be the top switch, but not able to console into the 2nd member. I get the screen stating the console is available but never get the prompt to login. Is this expected behavior?On our stacks of 3750v2's, I'm able to console to any switch in the stack?
View 1 Replies View RelatedI can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies View RelatedI have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies View Related