Cisco Switching/Routing :: 2911 Router With Base And Security
Feb 12, 2013
We have purchased a number of 2911 routers.We got Base & security license as we wanted to enable encryption. However we probably wont use the security.We are replacing 2811 routers.Unfortunately the 2811 routers have FXS ports with 2 - 4 POTS handsets - I completely forgot about these ports when I was ordering.Now I have VIC3-FXS cards which are ok in the 2911 but unfortunately I cant get them to work.I am missing PVDMs (well adapters anyway), and even if I got them the router wont take any commands relating to voice due to the license.Is is possible to 'rehost' the security and turn it into a UC ?I am new to these 2911 and Licensing.
View 1 Replies
ADVERTISEMENT
Mar 28, 2012
1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
View 2 Replies
View Related
May 6, 2012
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies
View Related
Nov 14, 2011
can we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies
View Related
Mar 6, 2012
When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies
View Related
May 19, 2013
I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies
View Related
May 7, 2013
I have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies
View Related
Jan 29, 2012
I have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
View 6 Replies
View Related
Jan 7, 2013
I have a 2911 router with 15.1(4) Ios Version. I need to enable the evaluation sna feature but when I try to enter the command "license feature snasw" but I get an error, the command "License feature" does not exist.
View 3 Replies
View Related
Oct 8, 2012
I am planning on having a contractor in to configure some new routers and would like for him to login using the local account on the routers while company personal continues to use radius is this possible.
View 6 Replies
View Related
Oct 31, 2012
My engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
View 3 Replies
View Related
Dec 30, 2012
I am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies
View Related
Jun 10, 2012
whether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies
View Related
Jan 29, 2013
We have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
View 2 Replies
View Related
Mar 19, 2013
I am having 2911 router running with C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)IOS and i have configured the following commands for eigrp
-router eigrp 100
-network 10.20.0.0
-no auto-summary
It takes all 3 commands but when i check through show run command i am not seeing no auto-summary command.
View 5 Replies
View Related
Sep 4, 2012
how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
View 1 Replies
View Related
Dec 27, 2012
I have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
View 4 Replies
View Related
Jan 7, 2013
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies
View Related
May 16, 2013
i have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
View 6 Replies
View Related
May 27, 2013
i'm trying to install the security licenses on a 2911 router and is giving the error shown in the attached file
View 4 Replies
View Related
Apr 26, 2012
We will deploy several 4507 with 2xsup7 as a L2 access switches for our office.Does LAN_Base IOS version support SSO or we need purchase IP_Base IOS (L3)?
View 1 Replies
View Related
Oct 26, 2011
I have been looking to find out the list of features that the IP Base IOS has for the 3750X series switch. What would be ideal is a comparable list but essentially I need to know which of the LAN Base/IP Base/IP Services has SSH functionality.
View 1 Replies
View Related
Sep 9, 2012
Full feature set for IP Base with the 3750x.I just wanted to verify that I could create a routed port, turn ip routing on, and create static routes as well as a default route. From what I can find, there shouldn't be a problem with this on the IP Base Feature Set, I just wanted to verify. Or any link for the Features of IP Base on the 3750x.
View 3 Replies
View Related
Nov 29, 2012
We have observed increase of CPU utilization of 50% after upgrade from 15.0(1)SE3 to 15.0(2).The SDM template is "desktop default" template.The increase of CPU utilization in Switches with LAN Base after upgrade is about 10%.
How to find the cause for the 50% increase ?This is command is the output of 15.0(2). The calculated sum for 5min process-utilization is 21% plus 1% interrupt is 22 %. Where is the rest ?
switch#sh proc cpu sorted 5min | exc 0.00
CPU utilization for five seconds: 30%/1%; one minute: 29%; five minutes: 28%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
169 135084171 33273787 4059 9.92% 8.94% 8.73% 0 Hulc LED Process
83 80075989 13546109 5911 5.60% 5.39% 5.38% 0 RedEarth Tx Mana
[code].....
View 17 Replies
View Related
Nov 1, 2011
why Cisco make 3560x switches with Lan Base(no routing functions)? What happen if I load an Image L3, previously downloaded? my device lost the warranty? or it doesn matter?
View 1 Replies
View Related
May 8, 2010
I want to block gtalk on my new cisco 2911 security enabled router.
View 3 Replies
View Related
Dec 8, 2012
I am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies
View Related
Mar 26, 2013
Would like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies
View Related
Oct 29, 2012
I upgraded an image on 3750 from Lan base to IP base, it worked fine. howver im just wondering if there any licensing implications, did the upgrade a few weeks ago, would the switches still work on a temp license somehow?
View 2 Replies
View Related
Feb 25, 2012
I have 3750 Switch and need to activate the ipservices on it , it is need a license file to switch from ipbase to ipservices , if i installed the ipservices image from cisco site , do i still need an activation key to use it??
View 7 Replies
View Related
Jul 5, 2012
I would I upgrade this from a LAN base to ip services?
View 2 Replies
View Related
Mar 3, 2013
I am bringing up a 3750x and a 2911 to replace a 3745 router with switchport module. I was plannng on moving all the VLAN interfaces off the 3745 onto the 3750x and turning up EIGRP. I discoved the 3750 has the LAN Base license, so I can't run eigrp off of it. My question or worry now is, will the LAN base license prevent the switch from doing interface VLAN routing between the different VLAN's configured on it or will I have keep all the VLAN interfaces on the new router and just have a router on a stick setup?
View 4 Replies
View Related
Nov 19, 2012
I'd like to know if is it possible to load lan base image on Cisco Switch 2960 TC-S. This model (WS-C2960-48TC-S) come with lan lite image and it's the same (phisically) of the 2960 TC-L (lan base image).If I try to upload the lan base image on flash of 2960 TC-S will works?? ..or the switch goes damaged?
View 2 Replies
View Related
