Cisco Switching/Routing :: 3750 - LAN Base License Limitations
Mar 3, 2013
I am bringing up a 3750x and a 2911 to replace a 3745 router with switchport module. I was plannng on moving all the VLAN interfaces off the 3745 onto the 3750x and turning up EIGRP. I discoved the 3750 has the LAN Base license, so I can't run eigrp off of it. My question or worry now is, will the LAN base license prevent the switch from doing interface VLAN routing between the different VLAN's configured on it or will I have keep all the VLAN interfaces on the new router and just have a router on a stick setup?
View 4 Replies
ADVERTISEMENT
Dec 8, 2012
I am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies
View Related
Mar 26, 2013
Would like to ask what is the rigth SKU license for WS-X3750-24P-L for LAN Base to IP Base Upgrade License
View 3 Replies
View Related
Jan 7, 2012
The model WS-C3750X-24T-L is only Lan Base. We need this switch to use EIGRP Protocol. Does it exist a License for supportting IP Base o IP Services Feature Set?
View 4 Replies
View Related
Jul 30, 2012
we recently purchased L3 daughter cards (N55-D160L3-V2) for our 5548UPs along with the LAN Enterprise Services licenses (N55-LAN1K9).
I installed the cards and Ent Svcs lic this past weekend and everything went well excep that I couldn't enable the EIGRP feature .. apparently EIGRP requires the LAN Base (N55-BAS1K9-BUN) license even when you have the Enterprise lic installed, so I was able to dig up that license eventually (which comes with the L3 daughter card, incidentally). Another side effect of not installing the Lan Base lic is that the L3 card/module will be in an "offline" state until the Lan Base lic is installed. Either way, everything was working normally in L2 mode at this time.
So, here I was thinking I was ready to proceed with enabling L3 - this morning I installed the LAN Base license on one of the 5548s which apparently triggered the L3 Daughter card module to go active and triggered a switch reboot. Ok, not that big of a deal, knew that was probably coming. I expected the switch to come back up normally .. NOPE. The switch went into a continual reboot cycle where the console prompt would appear, then about 30 seconds later, would reboot again.
I finally ended up re-installing the original L2 card and the switch came right up. I see that LAN Base and LAN Enterprise are both still installed as well.
What have I done wrong here? Why did the switch go into a continuous reboot cycle once I installed the LAN Base license?
Here are more details :
Software
BIOS: version 3.5.0
loader: version N/A
[Code]....
View 10 Replies
View Related
Oct 29, 2012
I upgraded an image on 3750 from Lan base to IP base, it worked fine. howver im just wondering if there any licensing implications, did the upgrade a few weeks ago, would the switches still work on a temp license somehow?
View 2 Replies
View Related
Feb 25, 2012
I have 3750 Switch and need to activate the ipservices on it , it is need a license file to switch from ipbase to ipservices , if i installed the ipservices image from cisco site , do i still need an activation key to use it??
View 7 Replies
View Related
Aug 14, 2012
I've got a bunch of 3750-X switches all running IP Base and acting as a routed access layer. They run OSPF in a totally stubby area with the distribution layer (Nexus 7K) as the ABR. We also have a physically separate management network into which the fa0 management interface of the 3750-X is connected. The management network itself runs OSPF and has multiple subnets and external access.
On the 3750-X, I'd ideally like to be able to run some sort of separate OSPF process for the management network or at the very least have a static default route for management traffic pointing out the fa0 interface, but clearly not have it interfere with the main default route for data traffic coming from the N7K ABR. Normally I'd just create a management VRF, sling the fa0 interface into it and run a separate OSPF process in that VRF. The problem is you can't create VRFs in IP Base! Surely there must be a way to do this? Cisco don't really expect customers to upgrade to IP Services just to have a working OOB Management network, do they?!
View 4 Replies
View Related
Nov 9, 2011
I have cisco 3750 with ipservices license and I am running with c3750e-universal-mz.122-50.SE2. And I would like to upgrade the IOS " k9" IOS. ie c3750e-universalk9-mz.122-50.SE2. Is there any license required for that ?Also any difference in the IOS upgrade procedure.
View 1 Replies
View Related
Apr 17, 2012
I want to turn on EIGRP functionality on my layer 3 3750 stack. I noticed I was only running an IPBASE license. When I do show license all I notice I have an evaluation of IP SERVICES image (see output below). Can I use this evaluation license? Would it be same as the full license or would it have limited functionality? Also, how do I make it the active license?
Q9-Switch#sh license all
License Store: Primary License Storage
Store Index: 0 Feature: ipbase Version: 1.0
License Type: Permanent
License State: Active, In Use
License Priority: Medium
License Count: Non-Counted
License Store: Evaluation License Storage
Store Index: 0 Feature: ipservices Version: 1.0
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
Evaluation total period: 8 weeks 4 days
Evaluation period left: 8 weeks 4 days
License Priority: None
License Count: Non-Counted
View 4 Replies
View Related
Sep 16, 2008
When installing the license for a 3750-E I get an error that the license doesn't reside on the flash though dir reveals the image in flash. Seen this, know of a resolution?
View 5 Replies
View Related
Dec 6, 2011
I recently added a 3750X-24P-L into a stack of 3750V2 switches. I did so by getting the temporary upgrade license from LAN Base to IP Services; I added the switch no problem. I now have the permanent license and I was wondering if I could install the permanent license without having to remove the switch from the stack. I tried a license install but that failed. The switch is not currently the master but I figured I might promote it and then try the install.
View 4 Replies
View Related
Mar 28, 2012
1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
View 2 Replies
View Related
May 6, 2012
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies
View Related
Nov 14, 2011
can we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies
View Related
Apr 3, 2013
We are trying to migrate WCS base license to NCS 1.1 .We have procured the migration license .In the licensing guide , it is mentioned as "L-WCS-NCS1-M-K9 License first, before adding the licenses migrated from your WCS installation"
1)Whether we need to add this migration license in WCS before genrating XML file or
2)Before adding XML file in NCS we need to add this in NCS ..
View 11 Replies
View Related
Aug 7, 2012
I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
View 4 Replies
View Related
Jan 27, 2013
We have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.
View 1 Replies
View Related
Jan 2, 2012
I've been reading the documentation for the new 3750v2 switch, and I'm wondering is the IPBase license supports FULL OSPF. The product sheet notes that it supports OSPF in the IPBase license, but then further down the page it notes that for advanced routing functions (EIGRP,OSPF) you need the IPServices license. Are there any limitations to the OSPF process on a 3750v2 with the IPBase license?
View 3 Replies
View Related
Dec 13, 2011
Any limitation on building an etherchannel on the abovementioned linecard, when bundling more than one port on the same card? The 4506 is using a 6L-E supervisor engine 12.2(54)SG1.
If it's done on a 6500 with a WS-X6148-GE-TX linecard it effectivley can only reach 1gb throughput.
View 2 Replies
View Related
Jul 17, 2012
I am working on ASA 5505 with Base License that uses 3 VLAN's.
-My VLAN 1 is for used for my home network.
-VLAN 2 is connected to the public Internet and my IP gets assigned by ISP dynamically.
-VLAN 3 is DMZ where I will have few VM's that would need access to and from the Internet.
I am looking to work with following:
1) 172.16.0.2 that sits on DMZ will need to access public Internet over port 80
2) Permit access from the Internet over port 3389 to 172.16.0.2
3) Permit any host on private VLAN (192.168.0.0 network) to access 172.16.0.2 over the port 3389
4) Permit second VM on the DMZ VLAN let say 172.16.0.3 to access public Internet on all ports. Access in to this host is not permitted.
5) For some reason DHCP hosts are NOT getting DNS (8.8.8.8) entry when IP hets assigned or renew. I have a statements below but it is not working.
Also, if ACL rules for VoIP are written correctly. The goal is to permit these ports (SIP related) to access VoIP router. [code]
View 1 Replies
View Related
Dec 28, 2011
I'm tring to setup a DMZ for a guest wireless off of a 5505. So this device has a base license. It has vlan1 and vlan 2 for inside and outside.Another vlan is configured to be a failover for the currently active wan connection. It is using the "no forward interface" command.Can I add another vlan as a DMZ if I use the "no forward interface" command? [code]
View 6 Replies
View Related
May 11, 2011
I have ASA 5505 with base licence. I configured NATing and VPN(site to site). All are working fine.My ASA is base license so i created 2 VLANS, one is inside and outside.Inside i am using 10.91.40.0/24 serie IP addresses.Below are the new requirements that i need to configre:
1. First 30 IP addresses only needs internet directly.( Servers and Management)
2. If remaining IPs likes to use web then traffic needs to forward one proxy server( where he gives user authentiation)
View 2 Replies
View Related
May 24, 2011
My ASA 5505 base license allows for three VLANs, the third one can only initiate traffic to one other VLAN (as specified by no forward interface vlan <number> on the third VLAN). This doesn't mean it can't "access" the other VLAN, it just can't initiate traffic to it. A lot of people get that wrong.Let's say you've got three VLANs, one is OUTSIDE, two is DMZ, and three is INSIDE. On the second VLAN would I enter the no forward interface as vlan 3, then set the name via the nameif command and everything will work just fine. The DMZ will not be able to initiate traffic to the INSIDE, but will to the outside, and assuming you have your ACLs and NAT set up properly, it will be able to respond to traffic from the INSIDE.
Would that be best practice or would I enter the "no forward" interface as in VLAN 1, thus is being able to respond to traffic from the outside as opposed to the inside.
I had a DMZ set up but since there was an intrusion into my network, I am building it again.
View 2 Replies
View Related
Jun 30, 2012
How to install IP base liecense and Unified communication liecense in 2921 router?
View 1 Replies
View Related
Sep 22, 2012
I have a couple of 5505's with base licenses. One of the two has a limited output when running the sho version command, as it has a restricted license. What license I would need to buy in order to bring it up to "normal" base license ?
View 1 Replies
View Related
Sep 1, 2011
Well, I tried using the cisco configuration for ASA 5505 for blocking P2P: url...but this configuration only is usefull with programs like Kazaa, so I try this configuration to block ARES but the problem is that ARES try to make downloads from different ports, ¿How do I block ARES if there are sereveral ports ?
View 1 Replies
View Related
Dec 18, 2011
we have a cisco ASA5505 with base license and 3 interface configured. Internal 192.168.1.1/24 DMZ 172.16.0.1/24 Outside 20.20.20.20/24 The DMZ is configured to allow the traffic pass to the outside interface only (base license allow only traffic to one interface) in order to let clients on this network to browse internet. On the outside interface there's a nat configuration that let the port 443 to be natted to an in internal server. Is it possible to let the clients in DMZ to access to the internal server on port 443 from the outside interface?
View 3 Replies
View Related
Jul 13, 2012
basic step to blocking site on ASA 5505 version 8.2(1) base license using CLI
View 1 Replies
View Related
Mar 29, 2012
I have a base 5505 and would like to get AnyConnect working. To do that, would I have to first purchase either an essentials or premium license and then purchase the AnyConnect Mobile license?
View 1 Replies
View Related
Oct 24, 2011
we have a customer with a ASA 5510 with a CSC module in it. The device tells us the Base license has expired. The new license has been renewed - after - the grace period. The Trendmicro site tells us the Base license is valid until 21 october 2013 but the CSC refuses to acknowledge this. The module is able to fetch updates form the Internet so it does not look like a connection problem to me (it also has a plus license which is also valid till far into 2013 and that one works).Is it possible that the current license key is "dead" and the CSC expects a new license key because the grace period was expired?
View 1 Replies
View Related
Oct 11, 2011
We want to buy a ISE-3315-K9 for 500 end-devices.In the price-list I found the ISE-3315-K9 but cannot find the base license: L-ISE-BSE-500=. (I think I need this license)Will the shipment of the ISE-3315-K9 includes a 3000 end-points base license (maximum support of the ISE-3315) or do I need to order the base 500 license seperately?
View 1 Replies
View Related
Mar 25, 2013
Getting the following alarm from my ISE:Cause:Base License Enforcement Details: Base concurrent users exceed license allowable count.Currently only using 1656 out of 2000 base licenses so I'm not sure what the issue is. Running 1.1.2.145 patch 3.
View 1 Replies
View Related
