Cisco Switching/Routing :: Cannot Create Vlan On 2811
Dec 13, 2012
This is a 2811 rotuer running Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2) Not sure why this isn't working. Can see it expects to parse the command. Can see this device is vtp server. Can see other vlans were defined here.
Router(config)#vlan ?
accounting VLAN accounting configuration
ifdescr VLAN subinterface ifDescr
Router(config)#vlan 35
^
% Invalid input detected at '^' marker.
[code]....
View 5 Replies
ADVERTISEMENT
Jan 10, 2012
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies
View Related
Jan 24, 2012
I have an in production x2 4500's which I would like to add a new vlan and IP address to.
Sample config...
interface Vlan65
ip address 10.100.6.2 255.255.255.248
no ip redirects
no ip unreachables
no ip proxy-arp
standby 65 ip 10.100.6.1
standby 65 timers 1 3
standby 65 preempt delay minimum 120
View 5 Replies
View Related
May 22, 2013
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
View 12 Replies
View Related
Feb 4, 2012
i am stuck in a issue! unable to ping the SVI
i am design a small network for a office.
1 router 2811
1 switch 3750-e
Router is connected to the mpls cloud with ospf.
here re the config.
Router#
int fa0/0
ip 10.10.10.1 255.255.255.252
[Code]....
i connect my laptop and give ip 22.0.68.1 255.255.255.0 and default gateway 22.0.68.251but can not ping SVI VLAN 201 (22.0.68.251) ?
and from the SWITCH i can not ping the 20.20.20.2?
View 38 Replies
View Related
Apr 11, 2012
Is it possible to create a vlan on a standard 3925? We have no addon cards installed.
View 3 Replies
View Related
Jun 23, 2012
I am not able to create more than 256 VLAN in Cisco Nexus 5010 switch. While creating I am getting "No VLAN resources available for VLAN creation" Details below -
Switch model - 5010
Software : NX OS 4.0 (1a)
Error Message:
Nexus_5010(config)# vlan 417
ERROR: No VLAN resource available for VLAN creation.
View 5 Replies
View Related
Feb 7, 2013
Currently have two routers inside our network.
One is the default GW 10.1.1.13
One is Jump Router for ATT 10.1.1.12
Both connected to HP Procurve L2 switch
The ATT Router is 10.1.1.2Want to replace GW and Jump with one 3750 L3 switch.icomplish this with only one port g0/1 connected to HP Procurve?Can I make the switchport 10.1.1.13 and then create a ip vlan999 10.1.1.12?route all to 10.1.1.2Or do I just connect two ports, and hardcode them with an ip?
View 1 Replies
View Related
Aug 23, 2009
Aug 24 11:32:16.275 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to down
Aug 24 11:32:36.827 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to up
Aug 24 11:35:23.854 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/2, changed state to down
Aug 24 11:35:24.854 AEST: %LINK-3-UPDOWN: Interface FastEthernet0/1/2, changed state to downesw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)(code)
When the above problem happens, as work-around, we delete VLAN.DAT file on the Compact Flash of this 2811 router and recopy the VLAN>DAT file back to teh Compact Flash.
Then it runs for a few weeks and the same problem happened.
Then we put a new Compact Flash and recopied VLAN.DAT to new CF and it ran for 3 weeks and same problem started again.
Could be 2811 router motherboard? This customer has thousands of these 2811 routers in identical setups and this is the only router that is having this problem.
View 6 Replies
View Related
Sep 24, 2012
Current Situation:We are able to reach server IP -10.203.206.40 from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.
Requirements
==========
1) Now we would like to add one more L3 interface between 4506 & 4948 for redundancy purpose.
2) Make available Vlan 540 in 4948 from 4506... need to create two trunk links between 4506 & 4948 and allow vlan 540.
View 14 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
Feb 6, 2012
We have Cisco Cat4503 series L3 Switch and Cisco L2 2560 Series Switches, some of the users want to have a dynamic VLAN membership, and connecting with the network as mobile users,
can it possible and create dynamic VLAN for specific group of users.
View 6 Replies
View Related
Jan 11, 2013
I have set up a 2811 with seperate VLANs for phones, and another for computers/printers. Fa0/0 is trunked to a 3560 switch, which has all end devices plugged in. I have enabled the IP Routing commands on both devices, and from advice turned off proxy-arp on the VLANs on the router (unsure if this is causing the issue). The setup is as follows
Computer VLAN = 192.168.20.0
Phone VLAN = 192.168.50.0
Both on the same subnet, along with a router loopback address in the same subnet, at 192.168.10.1.I am having an issue understanding why, but if I try to ping a phone from a PC it times out. Or if I try to type the phone's IP into an internet browser to get the phone's GUI on screen, it fails. This should not be happening as IP routing has been enabled on both, and everything is in the same subnet, correct? PC's can ping other PC's and network printing works fine. Phones register and operate fine, but the two VLAN's will not interoute.Furthermore if I try and ping the router's loopback from the switch, it fails. But the trunk is up and operational because DHCP and devices work within their own VLAN. If I try to ping end devices from the switch, it returns 100%. There seems to be an issue with the router looping the different networks together.
View 35 Replies
View Related
Apr 8, 2013
I used two sf-300 switch and create 4 vlans and intervlan routing is working fine.
Port 1 - 10 -------------> Vlan 1
Port 2 -20----------------> Vlan 2
Port 3 - 30------------------> Vlan 3
Port 4 - 40--------------------> Vlan 4
giga1 -----------------> connected to router (This router used for intervlan routing).
SF-300 Port 1 is connected to Internet Modem. This modem worked as dhcp server also for vlan 1, my problem is that when vlan 1 is not communicate to vlan2,3,4 and 2,3,4 are not communicating.
How i can communicate vlan 1 to 2,3,4 vlan.
how i can connect the modem in switch? Access port or Trunk port ( Presently available in vlan 1 Access port)Any route i need to make? sf-300 or modem or router?
View 1 Replies
View Related
Jan 12, 2012
I want to create a VPN between two PC's, (the server "Data" and "Remote Desktop" check the topology below), the Router Clabeck (cisco 2811 ) is connected to the internet through int f0/0 using a PPPoE connection and connects all the LAN PC's by PAT to the internet (you can see all the configurations in the Show Run below), the "Remote Desktop" is any PC with internet connection.
F0/1 F0/0
DATA--------------------SW-------------------ROUTER(Cisco 2811)---------------------INTERNET---------------REMOTE DESKTOP
192.168.1.51 192.168.1.254 201.122.53.177 192.168.1.1
Current configuration : 2116 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
View 1 Replies
View Related
Dec 20, 2010
what is the simplest way to create backup WAN connection?I have setup 2 WAN connection(2 ISP, 1 is DIA w/ fix ip, 2 is 3G), but if I enable both interface ,then I unplug WAN 1. no traffic goes to WAN 2.I have already have 3G connection enable all the time (w/ command "dialer persistent") Cisco 2811+ Cisco-HWIC-3G,
View 4 Replies
View Related
Mar 14, 2011
I have an ASR 1002. Behind that and across another small MAN network (considered inside) I have an ASA. On the remote end, I have a simple 2811.
I need to create a vpn peer from the remote router to both the ASR (to hand off traffic there) and also a peer at the ASA (to encrypto across the MAN). The ASR1002 has the serial connection (DS3) to our MPLS cloud in which the remote is on the opposite side of.
So basically, I've created a single isakmp policy with two crypto map's by the same name but set to different peers and placed on the remote router then applied it to the serial interface. This works fine. Now i throw in the ASA which is behind the ASR. However, the connection still comes through that ASR to get to the ASA.After setting it up, it works as long as I don't have the crypto map applied to the ASR. If i apply the crypto map to the so interface of the ASR, my asa vpn connection stops working.It almost seems as if the crypto map on the ASR is grabbing my enrypted traffic destined for xx.xxx.24.14 and trying to do something with it. [code]
Why can't i peer from my remote router to both the ASA and the ASR on the opposite end of the serial link?
View 1 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Mar 31, 2013
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
View 4 Replies
View Related
Sep 16, 2012
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies
View Related
Jun 13, 2011
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
View 3 Replies
View Related
Nov 20, 2012
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
View 2 Replies
View Related
Mar 26, 2012
I wanted to have 3 vlan for my switch just for security reasons.(We do not want different Vlan members interact with each other)
I created 3 untagged Vlans on 48 port switch.
So ports 1-16 in Vlan 192.168.1.1/25
So ports 17-32 in Vlan 192.168.2.1/25
So ports 33-48 in Vlan 192.168.3.1/25
View 3 Replies
View Related
Oct 23, 2011
I have four 2811 routers with IOS 12.4(15)T installed. Embedded Event Manager was introduced in IOS 12.3(4)T, why do I not have it?! I've been at this for over a month, when I try to see the command 'event manager' I get Unrecognized command? According to all EEM documentation I can find, this should work on our machines!
View 4 Replies
View Related
Apr 22, 2013
I need to know, can i create svi on the ASR 1002 ?
View 2 Replies
View Related
Mar 4, 2013
I want to confirm this is a licensing issue. On a 3750X with ipbase, I cannot create a vrf. So I would need the universal image, and that is a seperate license, correct?Is there a link that describes the difference bewteen ipbase and univeral images?
View 6 Replies
View Related
Jan 4, 2012
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
View 5 Replies
View Related
Oct 31, 2010
[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies
View Related
Jan 24, 2013
Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies
View Related
Aug 10, 2011
I am facing a problem on a 2811 router. The CPU is remaining around 60% and the router throughput is reaching at most 18 MB while according to the data sheet the 2811 maximum throughput is 61MB. I have checked the output interpreter in order to try and figure out the cause of the high CPU and to determine if it is affecting throughput but there are not processes consuming more than 10%. I have attached the show tech-support and the show process cpu history outputs.
View 11 Replies
View Related
Jan 19, 2012
I currently have a 2811 and a LAN setup via a sub-interface FA0/1.3 and using a HWIC-AP I have a sub-interface dot11radio 0/1.5. I have them setup to work and surf the inet great, but I have recently been overly annoyed with the fact that the wifi cannot access windows shares on desktops and visa versa with the laptops.
The trick to make this happen is currently they are not on the same subnet. I know the answer is bridging the interfaces but when I do this using the simple commands:
bridge 1 protocol ieee
interface x & y
bridge-group 1
Although what should be simple has failed (good thing I tftp'd my working config). Here is my current configuration.
interface FastEthernet0/1.30
encapsulation dot1Q 30
ip address 192.168.3.1 255.255.255.0
[Code].....
View 3 Replies
View Related
Feb 17, 2007
Whether Cisco has part number for the large fan in 2811. I know p/n for small fan is already there, but I can't find any for large one( I think it s fan 3).
View 10 Replies
View Related
Sep 25, 2012
We have a site and on that site we have a server which is down form last two days. However , to manage these devices we are not using any tools. We are not able to find this server that where it is located and on which switch it is connected to.
I want to know that the timer for mac address is 5 minutes and arp timeout is 4 hours . Is there any way to find out the mac address of the server . I feel like this can we done with cef ? Is it true or not I am not sure. I am running 3750 stacks and 2811 routers. 3750 stacks are working as layer 3 devices. They are also running the pretty new IOS 12.2(53)SE.
According to my understanding now a days CEF entry does not expire if we are not using them. They remain in cache as we are running with destination base CEF.
View 4 Replies
View Related
