Cisco Switching/Routing :: 3650 - Unable To Add New VLAN

Mar 11, 2012

We have a 3750 and a 3560 defined as a layer 2 switches. One gig port on each switch  is trunked to layer 3 switches, which containall the VLAN definitions etc. The other gig port on the 3650 and 3750 switches are trunked together to provide an alternative path in the event of a failure.

We have added a new device to the 3750 and given it a VLAN 9, and the VLAN added to allowable VLANS on both trunk ports  between the layer 3 and layer 2 devices ie:

switch port trunk allowed vlan 9,10,20,30,40,50,60,90,200,202,206,211,212,700.
From either of the 3750 or the 3560 we can ping any device on any VLAN on any switch in this group with exception ofVLAN 9.  We can however ping the ip address of VLAN 9 on the layer three switches.

View 2 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 3650 PBR Is Not Working

Mar 14, 2013

I have created a PBR in 3650 switch to route traffic from a specific IP address to a specific next hop or IP address(Router)
 
ROM: Bootstrap program is C3560 boot loader
BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
 
SW1 uptime is 6 weeks, 2 days, 16 minutes
System returned to ROM by power-on
[Code]....

View 6 Replies View Related

Cisco Switching/Routing :: Connecting 3750 And 3650 Switches Together

Sep 16, 2012

I have a small network using a 24 port 3750 switch.  I need to add five computers in another room and only have one Cat 6 cable running there and no room left on the 3750.  I got a 3650 to put in the new room with the new computers.  The problem is, whenever I plug the new switch into the 3750, it shuts down the port and gives me an err-disable.  I can do a shut/no shut and re-enable the port.  I searched the web and read about trunking and clusters.  I'm not sure which, if either, is appropriate.  I see various documentation that shows you can put one switch behind the other.  But nothing tells me the configuration which will allow it.

View 9 Replies View Related

Cisco Switching/Routing :: How To Configure RSTP On Catalyst 3650 And 2950

Aug 3, 2011

Configuring a network with Rapid Spanning Tree Protocol. There's a combination of Cisco 3650s, 2950 and 2960 switches. It is a flat Layer 2 network with a single VLAN. CLI configuration?

View 3 Replies View Related

Cisco Switching/Routing :: Static Load Balancing On 3650-X IP Base?

Nov 22, 2011

Does 3650-X IP Base support Static Load Balancing or i should upgrade to ip service SW ?

View 4 Replies View Related

Cisco Switching/Routing :: 3650 / 5505 / 1252 - Access Between VLANs

Dec 22, 2012

I have set up a scenario for a small business and have some questions about how to manage the access between the VLANs. Is there is a better / another way to do it. See the attached picture for the topology / info.
 
My question is:  
My switches is set up with x numbers of VLANs and a routed port (no switch port) to the ASA for internet connectivity. How is the best (or only??) way to manage the access between the VLANs?  Is it ACL's on the switch?
 
And by "managing access" I mean VLAN 50 (public WiFi) only have access to the internet, only management servers have access to management VLAN, Client VLAN only have RDP access to server VLAN and so on. Is there any way to do this in the ASA (or add another (gigabit) router to the topology)) or it the only way to have lots of ACL's on the switch itself? I have thought about "router on a stick", but then I imagine there will be a bottleneck between the switch and the ASA?  

(Equipment is 2 x 3650G, ASA5505, AP1252 - see attached file).         

View 3 Replies View Related

Cisco Switching/Routing :: 3650 - Speed Negotiation In Interface Gigabit

May 18, 2013

I have a question about speed negotiation process between interfaces. I have 3650X Sw and 2960S-48port. All ports of two are GigabitEthernet, however the link between them is only 100Mb/s, Full duplex. I try to set the speed 1000 Mb/s manually in the interface then the interface never up. Its status is down/down. I must set back to speed auto. I show interface Gigabit0/24 in Sw 3650-X and figure out that there are many output drop (over 600000). I clear counter then after two days the output drop is over 70000. This link is trunk link between two switches, all ports of access SW are Gigabit and connect to PC. First, I thinks the 3650X is throttled somewhere in  output direction of trunk link. But there is another trunk link (Gi0/23) to another 2960S-48port and no output drop number in this interface. This Giga 0/23 speed is 1000 Mb/s (auto speed, auto duplex)
 
Does any outside things impact the speed negotiation process between 2 interfaces? And output drop number may caused by abnormal speed between two Gigabit interface?

View 1 Replies View Related

Cisco Switching/Routing :: Catalyst 3650 Doesn't Pass Voice?

May 22, 2013

|_voip PBX___|-----|__3650___|------fiber-------------|__3650_____|------|_voipphone__|     I have a case where voipphone is registered on the voippbx but peaple on both end can't hear each other . No ACL on both 3650 , no firewalls between them , distance is about 2 miles . I tried to make  telnet x.x.x.x 1720 or 1719 or 1721 (h323 ports) to opposite switch  -connection refused . How can test if ports are open on the 3650 ? Is it coorect If I  create allowing acl and apply it on both 3650 on the interfaces connected one switch to voippbx "IN" , second switch on the interf connected to voipphone "IN" ?

View 3 Replies View Related

Cisco Switching/Routing :: 3560 - Unable To Perform VLAN Routing

Apr 28, 2012

We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing.  We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.

View 17 Replies View Related

Cisco Switching/Routing :: Can Use Catalyst 3650 With A Fiber Connection To Connect The HBA Esxi Server Card

Sep 20, 2012

I have a question regarding fabric storage and cisco catalyst switch 3650.My plan is connecta a esxi server to a nexus switch and then to a san storage. I want add a new switch to have a redundant link between esxi and the storage.Can I use a cisco catalyst 3650 with a fiber conecction to connect the HBA esxi server card  to 3650 sw and the SAN storage to the 3650 sw ?

View 2 Replies View Related

Cisco Switching/Routing :: SG-300 Vlan Unable To Access Internet

Apr 1, 2013

I am using a Cisco SG-300 28 port switch in layer 3 mode as my default gateway for all my devices. I have two vlans on the switch, vlan 1 and vlan 4. Both are pulling valid IP addresses in their scope from the DHCP server, and both have valid DNS settings. I set a static route to the Internet on the switch to our firewall (192.168.5.254). All devices connected to vlan 1 are able to access the Internet, however all devices connected to vlan 4 cannot get past the switch. A tracert from one of these devices shows it hits the switch as the gateway, but gets no further. [code]

View 4 Replies View Related

Cisco Switching/Routing :: 2811 - Unable To Ping SVI VLAN

Feb 4, 2012

i am stuck in a issue! unable to ping the SVI

i am design a small network for a office.

1 router 2811
1 switch 3750-e

Router is connected to the mpls cloud with ospf.

here re the config.

Router#
int fa0/0
ip 10.10.10.1 255.255.255.252

[Code]....

i connect my laptop and give ip 22.0.68.1 255.255.255.0 and default gateway 22.0.68.251but can not ping SVI VLAN 201 (22.0.68.251) ?

and from the SWITCH i can not ping the 20.20.20.2?

View 38 Replies View Related

Cisco Switching/Routing :: VLAN810 / Same VLAN Host Unable To Pinging

Feb 4, 2013

i configured  the VLAN810, with DHCP services,  while i try to ping the host which is connected to gi 1/0/2 from my gi 1/0/1 , i can't ping the same vlan host , while i try to debug ip icmp its showing ,

C3750XB11#sh running-config
Building configuration... 
Current configuration : 12053 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec

[code]....

View 5 Replies View Related

Cisco Switching/Routing :: 5548 Unable To Communicate With TSM Server That Is On Same VLAN

Apr 6, 2012

I have a Nexus 5548 installed (layer 2 device only) with several 10G ports supporting IBM P770 systems and a TSM (Tivoli Storage Manager) system on a single VLAN. All of the Nexus 5548 ports are configured for jumbo frames. I was ask to install a new server on the same VLAN as the others but as 1G port without jumbo frames to allow communications with the TSM server. I'm assuming that the 1G port for this new server without jumbo frames configured on the Nexus 5548 will not be unable to communicate with the TSM server that is on the same VLAN with it's Nexus 5548 10G port configure using jumbo frames.

View 5 Replies View Related

Cisco Switching/Routing :: Nexus 5010 - Unable To Create More Than 256 VLAN In N5k

Jun 23, 2012

I am not able to create more than 256 VLAN in Cisco Nexus 5010 switch. While creating I am getting "No VLAN resources available for VLAN creation" Details below -
 
Switch model - 5010
Software : NX OS 4.0 (1a)
 
Error Message:
Nexus_5010(config)# vlan 417
ERROR: No VLAN resource available for VLAN creation.

View 5 Replies View Related

Cisco Switching/Routing :: 3750X - Unable To Access VLAN IP Pool

Mar 19, 2013

I have one issue on Vlan in Cisco 3750X switches , I have 2 Offices  , I am sitting at corp OFfice and i have one 3750 ( 10.10.1.36)Switch at my location , in my remote office i have one more switch 3750 ( 10.10.33.1) and i am able to access the both vlan IPS with out any issue , now i have some network components in Vlan33 ( 10.10.33.1) at my remote office . i am able to ping 10.10.33.1 IP from my corp office , but i am not able to ping any network devices in 10.10.33.5 example : 10.10.33.5 is my Cyberoam IP at remote location and i am not able to ping , i have taken a trace route and not able to find the issue as i am not much femilar , ping 10.10.33.5 at remote location devicec
 
I am giving the Configuration for both locaitons below :
 
10.10.1.36 - Corp Office 3750 Switch:
sh run
L3-#sh running-config
Building configuration...

[Code].....

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 7010 - Unable To Ping Within VLan

Jul 10, 2012

Yesterday I configured the 7010 Nexus switch. I created a VDC and allocated few ports and configured VLAN for testing. After enabling feature interface-​vlan i was allowed to configured L3 interface for the vlan. I assigned ip address and connected few server to check the reachability but it says Destination Host Unreachable.
 
NX OS Ver : n7000-s1-dk9.5.2.4.bin
 
Configuration of the VDC below.
 
feature telnet
feature udld
feature interface-vlan
feature lacp
[Code]....

View 2 Replies View Related

Cisco Switching/Routing :: Unable To Connect A Wi-Fi Modem Within 2960 Switch Having VLAN 1

May 19, 2013

I am unable to connect a Wifi Modem wiith 2960 Switch having VLAN 1,Attached is the network diagram,what configurations i have to modified it,I need to Connect A Wifi Modem on VLAN 1 ,Connectivity is working fine between VLAN 10 and VLAN 1.What should be the next step to Connect Wifi Modem to VLAN 1 so that Users on VLAN 10 should connect to Internet.

View 14 Replies View Related

Cisco Switching/Routing :: Unable To Apply IP Policy Route-Map To VLan 4 In C-3750

Apr 22, 2012

Here is my configuration below , i have upgraded my C-3750 switch IOS from IPbase to IPservices , after upgrading i have tried to apply PBR on my Vlan 4 and failed , when i am tying to apply route-map to Vlan4 the command was taking but i am unable to see the route-map when sh run , i am giving the command as "ip policy route-map TTSL" in my Vlan4 , below is the configuration.
 
In Vlan2 i have connected one ISP and Vlan4 I have connected one ISP , my local subnets are 192.168.1.x and 192.168.2.x , now i want to route the 192.168.1.x traffic from Vlan2 and 192.168.2.x Traffic from Vlan4 .
  
sh boot
coreswitch#sh boot
BOOT path-list      : flash:c3750-ipservices-mz.122-35.SE5/c3750-ipservices-mz.122-35.SE5.bin

[Code].....

View 9 Replies View Related

Cisco Switching/Routing :: ASA 5520 - Unable To Reach VLan System While Connecting From VPN

May 27, 2013

I have a multiple Offices in my location , all my external users are connecting my site using Cisco Client to site VPN and accessing my 2 sites , All users are able to access my 2nd office servers which are in 10.10.0.x pool , I have a different vlan in that same location with 10.10.35.x series and users are not able to access this pool servers , I am not much familiar with Routing . i am using ASA 5520 firewall .

View 11 Replies View Related

Cisco Switching/Routing :: 2811 - Error Unable To Find Entry For VLAN (1)

Aug 23, 2009

Aug 24 11:32:16.275 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to down
Aug 24 11:32:36.827 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to up
Aug 24 11:35:23.854 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/2, changed state to down
Aug 24 11:35:24.854 AEST: %LINK-3-UPDOWN: Interface FastEthernet0/1/2, changed state to downesw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)(code)

When the above problem happens, as work-around, we delete VLAN.DAT file on the Compact Flash of this 2811 router and recopy the VLAN>DAT  file back to teh Compact Flash.
 
Then it runs for a few weeks and the same problem happened.
 
Then we put a new Compact Flash and recopied VLAN.DAT to new CF and it ran for 3 weeks and same problem started again.
 
Could be 2811 router motherboard? This customer has thousands of these 2811 routers in identical setups and this is the only router that is having this problem. 

View 6 Replies View Related

Cisco Switching/Routing :: 3560 Possible To Create Vlan Inside Transport Vlan?

Jan 10, 2012

Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?

View 3 Replies View Related

Cisco Switching/Routing :: 3750 - Extending VLAN To Remote Switch That Already Has VLAN ID In Use

Jan 10, 2013

I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
 
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
 
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
 
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.

View 4 Replies View Related

Cisco Switching/Routing :: Route Data From Vlan 10 To Vlan 20 On 2960s?

Mar 31, 2013

i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
 
Uplink port config for gi 1/0/28 is:
 
switchport mode trunk
switchport trunk alloved vlan 10,11
  
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
 
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10

View 4 Replies View Related

Cisco Switching/Routing :: 3750G / VLAN 1 Is The Only VLAN And Its Disabled

Sep 16, 2012

I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?

View 4 Replies View Related

Cisco Switching/Routing :: L2tpv3 Vlan-to-vlan Tunnel On 890

Jun 13, 2011

I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
 
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
 
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
 
I configured a vlan interface as follows.

(config)#vlan 200
 (config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
 
I don't see the 'xconnect' command in this context. What's wrong with my configuration? 

View 3 Replies View Related

Cisco Switching/Routing :: Low Bandwidth On 3750 From Vlan To Vlan?

Nov 20, 2012

We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
 
Here are the Layer 3 Design:
 
Client     ->     vlan 2 - Switch - vlan 7     ->     vlan 1 - ASA 5505     ->     ISP
 
The Layer 2 Design:
 
Client     ->     Gig2/0/13 - Switch - Gig4/0/43     ->     Eth0/1 ASA5505     ->     ISP
 
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
  
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:

switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
 
And we have following error message in the log from the switch:

%PLATFORM_UCAST-4-PREFIX: 

One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue. 
 
Here are the relevant config:
 
ASA Interface on the Switch:

interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
 
Client Interface on the Switch:

interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable

[code]...

View 2 Replies View Related

Cisco Infrastructure :: 3550 Versus 3650 For Enhanced Image In Terms Of Routing

Apr 9, 2006

How does the 3550 with enhanced image compare to the 3650 with enhanced image in terms of routing functionality?

View 5 Replies View Related

Cisco Switching/Routing :: How To Migrate From Fixed Router To Vlan Routing On 4507

Feb 16, 2012

Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.

View 4 Replies View Related

Cisco Switching/Routing :: Multiple VLAN Routing Tables For 3750 Catalyst

Oct 24, 2012

I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 3750 Multi-cast VLAN Routing

Oct 28, 2012

I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).

View 2 Replies View Related

Cisco Switching/Routing :: Does Catalyst 3550 Support Inter Vlan Routing

Jul 24, 2007

Does Catalyst 3550 switch support inter vlan routing ?

View 12 Replies View Related

Cisco Switching/Routing :: Inter VLAN Routing On N5548P Without L3 Daughter Cards

Jun 1, 2013

I have a DC topology based on 2 layers, access and aggregation, based on 2 pairs of N5548Ps, both without L3 Daugher Cards. My intent is to use the aggregation N5K pair as L3 inter VLAN layer, so I configured all the VLAN default GWs there. The 2 layers are interconnected via vPC, in a double-sided vPC topology for some N2Ks and some vSwitches. The point is that, despite connecitivity is working fairly ok, for some applications, like file transfer via either FTP or HTTP, between hosts in different VLANs, the performance is too poor. The file transfer starts ok, but after a while it becomes lower and lower. ICMP is working, but I can see some strange random behaviour, like having some packets taking more that 20 ms (sometimes 40 or more), whilst average is 2 ms.

I read through some articles saying that until you don´t have the L3 license (the one coming with L3 Daughter Cards) you can expect some weird behaviour on L3 level. Is that true?. What can I do apart of purchasing L3 Daughter Cards?. Can I enable L3 Basic license at the moment (I don´t need dynamic routing for now).
 
Here some excerpts of what I´m saying:
 
PING results:
10000 packets transmitted, 10000 packets received, 0.00% packet loss
round-trip min/avg/max = 0.809/2.496/57.559 ms
 System version: 5.0(3)N2(1)
 
License and features on the N5Ks:
 
switch# sho license usage
Feature                      Ins  Lic   Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
FCOE_NPV_PKG                  No    -   Unused             -
FM_SERVER_PKG                 No    -   Unused             -
ENTERPRISE_PKG                No    -   Unused             -

[code]....

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved